Warning, 2.5.3 eats filesystems
Hi!
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
Pavel
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: PCI device 10b9:1647 (Acer Laboratories Inc. [ALi]) (rev 4).
Prefetchable 32 bit memory at 0xf0000000 [0xf3ffffff].
Bus 0, device 1, function 0:
PCI bridge: Acer Laboratories Inc. [ALi] M5247 (rev 0).
Master Capable. No bursts. Min Gnt=12.
Bus 0, device 2, function 0:
USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 3).
IRQ 9.
Master Capable. Latency=16. Max Lat=80.
Non-prefetchable 32 bit memory at 0xfff70000 [0xfff70fff].
Bus 0, device 4, function 0:
CardBus bridge: Texas Instruments PCI1420 (rev 0).
IRQ 11.
Master Capable. Latency=168. Min Gnt=192.Max Lat=5.
Non-prefetchable 32 bit memory at 0x10000000 [0x10000fff].
Bus 0, device 4, function 1:
CardBus bridge: Texas Instruments PCI1420 (#2) (rev 0).
IRQ 11.
Master Capable. Latency=168. Min Gnt=192.Max Lat=5.
Non-prefetchable 32 bit memory at 0x10001000 [0x10001fff].
Bus 0, device 6, function 0:
Bridge: Acer Laboratories Inc. [ALi] M7101 PMU (rev 0).
Bus 0, device 7, function 0:
ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV] (rev 0).
Bus 0, device 8, function 0:
Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 18).
IRQ 5.
Master Capable. Latency=64. Min Gnt=2.Max Lat=24.
I/O at 0x1400 [0x14ff].
Bus 0, device 8, function 1:
Communication controller: ESS Technology ESS Modem (rev 18).
IRQ 5.
I/O at 0x1800 [0x18ff].
Bus 0, device 15, function 0:
IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev 195).
Master Capable. Latency=64. Min Gnt=2.Max Lat=4.
I/O at 0x1000 [0x100f].
Bus 0, device 16, function 0:
Ethernet controller: Accton Technology Corporation EN-1216 Ethernet Adapter (rev 17).
IRQ 11.
Master Capable. Latency=64. Min Gnt=255.Max Lat=255.
I/O at 0x1c00 [0x1cff].
Non-prefetchable 32 bit memory at 0xea001000 [0xea0013ff].
Bus 1, device 0, function 0:
VGA compatible controller: Trident Microsystems CyberBlade/XP (rev 99).
IRQ 11.
Master Capable. Latency=64.
Non-prefetchable 32 bit memory at 0xee000000 [0xefffffff].
Non-prefetchable 32 bit memory at 0xea400000 [0xea7fffff].
Non-prefetchable 32 bit memory at 0xec000000 [0xedffffff].
Non-prefetchable 32 bit memory at 0xea100000 [0xea107fff].Signature · 2 lines
(about SSSCA) "I don't say this lightly. However, I really think that the U.S. no longer is classifiable as a democracy, but rather as a plutocracy." --hpa
Quoted 4 lines · Pavel Machek
Hi!
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
The box has been rock solid before this. Configuration:
00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01)
ext3 filesystem, data=journal mode. P-II 400, 288MB.
Daniel
Signature · 3 lines
C makes it easy to shoot yourself in the foot.
C++ makes it harder, but when you do, it blows away your whole leg.
-- Bjarne Stroustrup-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 10 lines · Daniel Pittman
Quoted 4 lines · Pavel Machek
Hi!
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
I can confirm inode errors also. However, I can't be sure it's 2.5.3 that did it.
All of the errors I've had all seemed to be files included in the pre-patch that broke Configure.help into pieces. I don't know the code well enough, but if the errors could only have happened at file creation then that would rule out 2.5.3.
- --
Skip ID: 0x7EDDDB0A
-----BEGIN PGP SIGNATURE-----
iEYEARECAAYFAjxgf/EACgkQBMKxVH7d2wppeACg3g9HDKuibe/u0rpFlU4u+xrb pzAAoKfOKnvXJTzGYfUzs+/YeVDDVyMP
=UhON
-----END PGP SIGNATURE-----
Quoted 2 lines · Skip Ford
I can confirm inode errors also. However, I can't be sure it's 2.5.3 that did it.
Recall that pre3/pre4/pre5 had the missing ext2_inode_info initialisation bug. If you booted any of those, and have only just done a fsck, it could be a leftover artifact of a now-fixed bug.
Quoted 4 lines
All of the errors I've had all seemed to be files included in the pre-patch that broke Configure.help into pieces. I don't know the code well enough, but if the errors could only have happened at file creation then that would rule out 2.5.3.
Indeed, that change was in pre5, which was the last pre to feature aforementioned buglet.
Signature · 2 lines
| Dave Jones. http://www.codemonkey.org.uk | SuSE Labs
Quoted 7 lines · Dave Jones
Quoted 2 lines · Skip Ford
I can confirm inode errors also. However, I can't be sure it's 2.5.3 that did it.
Recall that pre3/pre4/pre5 had the missing
ext2_inode_infoinitialisation bug. If you booted any of those, and have only just done a fsck, it could be a leftover artifact of a now-fixed bug.
I jumped directly from 2.4.18pre1 to 2.5.3, and I didn't see any issues with the 2.4 kernel in the time I ran it.
This doesn't rule out a pre-existing corruption, of course, but it seems to me unlikely in the extreme. Er, in my case, of course. I can't speak for others.
Daniel
Signature · 4 lines
Yes, I hate that. You spend all this time trying to explain to people that
they don't *have* to hammer nails into their own heads all the time, only to
discover that they *like* it because it's all they've ever known.
Tim Bradshaw, _comp.lang.lisp_Quoted 5 lines · Pavel Machek
Hi!
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
Pavel
/me too. 2.5.3 ate my bookmarks.html (and perhaps other files too, I did not check yet). I just ran it up to the 1st freeze, then switched back to 2.4.17. Reiserfs then did a rather long log replay...
Olaf
Hi!
Quoted 2 lines
I can confirm inode errors also. However, I can't be sure it's 2.5.3 that did it.
I *know* it is 2.5.3.
Pavel
Signature · 2 lines
Philips Velo 1: 1"x4"x8", 300gram, 60, 12MB, 40bogomips, linux, mutt, details at http://atrey.karlin.mff.cuni.cz/~pavel/velo/index.html.
Quoted 7 lines · Daniel Pittman
Quoted 2 lines
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
Exactly the same thing here, and I bet it _is_ 2.5.3 and not a relict from a 2.5.3-pre patch because I switched directly from 2.4.17 to 2.5.3 without ever using any pre patch at this machine.
Signature · 1 line
# Heinz Diehl, 68259 Mannheim, Germany
Quoted 5 lines · Heinz Diehl
Quoted 2 lines · Daniel Pittman
Quoted 2 lines
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
Quoted 8 lines
Quoted 4 lines
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
Exactly the same thing here, and I bet it _is_ 2.5.3 and not a relict from a 2.5.3-pre patch because I switched directly from 2.4.17 to 2.5.3 without ever using any pre patch at this machine.
Very interesting. Which filesystems are mounted (other than ext2) and are you been able to reproduce it on 2.5.3-pre6?
Quoted 2 lines · Alexander Viro
Very interesting. Which filesystems are mounted (other than ext2) and are you been able to reproduce it on 2.5.3-pre6?
There are only ext2 filesystems available and one cd-rom.
I installed 2.5.3-pre6 and the machine runs for about 6 hours now (heavy load) and no error occured yet.
Signature · 1 line
# Heinz Diehl, 68259 Mannheim, Germany
Hi!
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 2 lines
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
Quoted 6 lines
Quoted 3 lines
Exactly the same thing here, and I bet it _is_ 2.5.3 and not a relict from a 2.5.3-pre patch because I switched directly from 2.4.17 to 2.5.3 without ever using any pre patch at this machine.
Very interesting. Which filesystems are mounted (other than ext2) and are you been able to reproduce it on 2.5.3-pre6?
For me, mounted filesystems look like this:
none on /proc type proc (rw)
none on /proc type proc (rw)
none on /proc type proc (rw)/dev/hda3 on /suse type ext2 (rw)
none on /proc type proc (rw)
none on /proc/bus/usb type usbdevfs (rw)/dev/cfs0 on /overlay type coda (rw)
Pavel
Signature · 2 lines
(about SSSCA) "I don't say this lightly. However, I really think that the U.S. no longer is classifiable as a democracy, but rather as a plutocracy." --hpa
Hi!
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 2 lines
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
Quoted 6 lines
Quoted 3 lines
Exactly the same thing here, and I bet it _is_ 2.5.3 and not a relict from a 2.5.3-pre patch because I switched directly from 2.4.17 to 2.5.3 without ever using any pre patch at this machine.
Very interesting. Which filesystems are mounted (other than ext2) and are you been able to reproduce it on 2.5.3-pre6?
Mounted filesystems:
/dev/hda2 on / type ext2 (rw)
none on /proc type proc (rw)
...
none on /proc type proc (rw)/dev/hda3 on /suse type ext2 (rw)
none on /proc type proc (rw)
none on /proc/bus/usb type usbdevfs (rw)/dev/cfs0 on /overlay type coda (rw)
(I wander what is responsible for mounting /proc hundred times?)
But... you should know that I'm strongly suspecting ide subsystem:
Feb 8 12:08:02 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:08:02 amd kernel: hda: drive not ready for command
Feb 8 12:08:02 amd kernel: ide0: reset: success
Feb 8 12:09:26 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:09:26 amd kernel: hda: drive not ready for command
Feb 8 12:09:26 amd kernel: ide0: reset: success
Feb 8 12:12:27 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:12:27 amd kernel: hda: drive not ready for command
Feb 8 12:12:27 amd kernel: ide0: reset: successI'm trying to test it with md5sum, but so far it behaves ok. [I wonder what directory I'll loose this time ... :-(]
Pavel
Signature · 2 lines
(about SSSCA) "I don't say this lightly. However, I really think that the U.S. no longer is classifiable as a democracy, but rather as a plutocracy." --hpa
Quoted 42 lines · Pavel Machek
Hi!
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 2 lines
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
Quoted 6 lines
Quoted 3 lines
Exactly the same thing here, and I bet it _is_ 2.5.3 and not a relict from a 2.5.3-pre patch because I switched directly from 2.4.17 to 2.5.3 without ever using any pre patch at this machine.
Very interesting. Which filesystems are mounted (other than ext2) and are you been able to reproduce it on 2.5.3-pre6?
Mounted filesystems:
/dev/hda2on / type ext2 (rw)
none on /proc type proc (rw)
...
none on /proc type proc (rw)/dev/hda3on /suse type ext2 (rw)
none on /proc type proc (rw)
none on/proc/bus/usbtype usbdevfs (rw)/dev/cfs0on /overlay type coda (rw)(I wander what is responsible for mounting /proc hundred times?)
But... you should know that I'm strongly suspecting ide subsystem:
Feb 8 12:08:02 amd kernel: hda: status timeout: status=0xd0 { Busy } Feb 8 12:08:02 amd kernel: hda: drive not ready for command Feb 8 12:08:02 amd kernel: ide0: reset: success Feb 8 12:09:26 amd kernel: hda: status timeout: status=0xd0 { Busy } Feb 8 12:09:26 amd kernel: hda: drive not ready for command Feb 8 12:09:26 amd kernel: ide0: reset: success Feb 8 12:12:27 amd kernel: hda: status timeout: status=0xd0 { Busy } Feb 8 12:12:27 amd kernel: hda: drive not ready for command Feb 8 12:12:27 amd kernel: ide0: reset: success
Quoted 13 lines
I'm trying to test it with md5sum, but so far it behaves ok. [I wonder what directory I'll loose this time ... :-(]
PavelSignature · 7 lines
(about SSSCA) "I don't say this lightly. However, I really think that the U.S. no longer is classifiable as a democracy, but rather as a plutocracy." --hpa - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Yep I warned about multmode pio.
I think I finally have a fix which does not use a copy of the request.
Andre Hedrick
Linux Disk Certification Project Linux ATA Development
WARNING: 2.5.3 -- IDE damages data! [was Re: Warning, 2.5.3 eats filesystems]
In reply to Heinz DiehlHi!
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 2 lines
2.5.3 managed to damage my ext2 filesystem (few lost directories); beware.
I can confirm that there are filesystem corruption issues with 2.5.3; after this message I rebooted and did a forced fsck which turned up around a half dozen inodes where the block count in the inode itself was too high.
Quoted 6 lines
Quoted 3 lines
Exactly the same thing here, and I bet it _is_ 2.5.3 and not a relict from a 2.5.3-pre patch because I switched directly from 2.4.17 to 2.5.3 without ever using any pre patch at this machine.
Very interesting. Which filesystems are mounted (other than ext2) and are you been able to reproduce it on 2.5.3-pre6?
[This is ext2 machine, IDE is
Bus 0, device 15, function 0:
IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev 195).
Master Capable. Latency=64. Min Gnt=2.Max Lat=4. I/O at 0x1000 [0x100f].
]
I did more testing, and yes, 2.5.3 does data corruption. This appeared in syslog:
Feb 8 12:08:02 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:08:02 amd kernel: hda: drive not ready for command
Feb 8 12:08:02 amd kernel: ide0: reset: success
Feb 8 12:09:26 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:09:26 amd kernel: hda: drive not ready for command
Feb 8 12:09:26 amd kernel: ide0: reset: success
Feb 8 12:12:27 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:12:27 amd kernel: hda: drive not ready for command
Feb 8 12:12:27 amd kernel: ide0: reset: success
Feb 8 12:13:05 amd log1n[103]: ROOT LOGIN on `tty6'
Feb 8 12:15:00 amd sendmail[150]: alias database /etc/aliases.db out
of date
Feb 8 12:15:00 amd sendmail[150]: MAA00150: from=pavel, size=2519,
class=0, pri=62519, nrcpts=2, msgid=<[email protected]>,
relay=pavel@localhost
Feb 8 12:15:04 amd sendmail[152]: MAA00150:[email protected],[email protected], ctladdr=pavel (8/100), delay=00:00:04, xdelay=00:00:04, mailer=relay, relay=[10.0.0.1] [10.0.0.1], stat=Sent (MAA10440 Message accepted for delivery)
Feb 8 12:18:17 amd kernel: hda: status timeout: status=0xd0 { Busy }
Feb 8 12:18:17 amd kernel: hda: drive not ready for command
Feb 8 12:18:18 amd kernel: ide0: reset: master: error (0x00?)And this happened on console:
croot@amd:~# cat /dev/urandom > /tmp/delme
root@amd:~# ls -al /tmp/delme -rw-r--r-- 1 root root 246845440 Feb 8 12:11 /tmp/delme root@amd:~# cp /tmp/delme /tmp/delme2 root@amd:~# cp /tmp/delme /tmp/delme3 root@amd:~# cp /tmp/delme /tmp/delme4 root@amd:~# md5sum /tmp/delme* 2da1568c45e298938353672d3a642714 /tmp/delme bc99762f3cf9a104e58e3f5708eeba99 /tmp/delme2 2da1568c45e298938353672d3a642714 /tmp/delme3 2da1568c45e298938353672d3a642714 /tmp/delme4 root@amd:~# cd /tmp root@amd:/tmp# ls -al delme delme2 delme3 -rw-r--r-- 1 root root 246845440 Feb 8 12:11 delme -rw-r--r-- 1 root root 246845440 Feb 8 12:14 delme2 -rw-r--r-- 1 root root 246845440 Feb 8 12:17 delme3 root@amd:/tmp#
As you can see, delme2 was damaged. I tried to do some heavy reads, but those seem to be okay.
root@amd:/tmp# hdparm /dev/hda
/dev/hda:
multcount = 0 (off) I/O support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) nowerr = 0 (off) readonly = 0 (off) readahead = 8 (on)
geometry = 2432/255/63, sectors = 39070080, start = 0
busstate = 1 (on)
root@amd:/tmp#
Pavel
Signature · 2 lines
(about SSSCA) "I don't say this lightly. However, I really think that the U.S. no longer is classifiable as a democracy, but rather as a plutocracy." --hpa
Quoted 1 line · Pavel Machek
For me, mounted filesystems look like this:
[....]
Yep. I sent the "mount" output already to Alexander Viro, unfortunately I did not Cc: the mail to lkml.
/dev/hda1 on / type ext2 (rw)
proc on /proc type proc (rw)/dev/hda6 on /usr type ext2 (rw)/dev/hda5 on /home type ext2 (rw)/dev/hdb5 on /var/spool/news type ext2 (rw)
tmpfs on /dev/shm type shm (rw)
tmpfs on /tmp type tmpfs (rw)
tmpfs on /var/tmp type tmpfs (rw)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev06)
(prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 64
I/O ports at e000 [size=16]
[....]
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modesVP_IDE: IDE controller on PCI bus 00 dev 39VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs laterVP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DHEA-36481, ATA DISK drive
hdb: Conner Peripherals 1275MB - CFS1275A, ATA DISK drive
hdc: CD-540E, ATAPI CD/DVD-ROM drive
hdd: CD-W54E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 12692736 sectors (6499 MB) w/472KiB Cache, CHS=790/255/63, UDMA(33)
hdb: 2496876 sectors (1278 MB) w/64KiB Cache, CHS=2477/16/63, DMA [....]
chiara:~ # hdparm /dev/hda /dev/hdb/dev/hda:
multcount = 16 (on) I/O support = 3 (32-bit w/sync) unmaskirq = 1 (on) using_dma = 1 (on) keepsettings = 0 (off) nowerr = 0 (off) readonly = 0 (off) readahead = 8 (on)
geometry = 790/255/63, sectors = 12692736, start = 0
/dev/hdb:
multcount = 8 (on) I/O support = 3 (32-bit w/sync) unmaskirq = 1 (on) using_dma = 1 (on) keepsettings = 0 (off) nowerr = 0 (off) readonly = 0 (off) readahead = 8 (on)
geometry = 619/64/63, sectors = 2496876, start = 0
Signature · 1 line
# Heinz Diehl, 68259 Mannheim, Germany