Skip to contentSkip to conversation

Connecting through parallel port

DISCUSSION Paulo J. Matos 4 participants 6 messages Feb 20, 2002 – Feb 21, 2002

lore
Share & tools
lore
#0 lore raw

Hi all,

I have a LAN at home and know I just got another computer to connect to the LAN, I also found a parallel-parallel cable. The network is ethernet, is it possible to connect the new computer using the parallel ports of the computers to the server of the LAN so that this new computer is able to have access to the internet and the rest of stuff?
What do I need to configure in the kernel?
Is there any how-to out there that answers this question?

Best regards,

Signature · 7 lines
Paulo J. Matos : pocm(_at_)rnl.ist.utl.pt
Instituto Superior Tecnico - Lisbon    
Software & Computer Engineering - A.I.
 - > http://www.rnl.ist.utl.pt/~pocm 
 ---	
	Yes, God had a deadline...
		So, He wrote it all in Lisp!
#1 lore raw

Hello,

There is a PLIP Howto in linuxdoc.

But i haven't been able to use plip after 2.4.17 even after the patch that should have resolved all the known issues.

Has anybody a clue?

#2 lore raw
In reply to Paulo J. Matos
Quoted 8 lines · Paulo J. Matos

I have a LAN at home and know I just got another computer to connect to the LAN, I also found a parallel-parallel cable. The network is ethernet, is it possible to connect the new computer using the parallel ports of the computers to the server of the LAN so that this new computer is able to have access to the internet and the rest of stuff?
What do I need to configure in the kernel?
Is there any how-to out there that answers this question?

There was a protocol called PLIP which did just what you want. I've used it many times for laptop install (Patrick even fixed it in Slackware at my request).

Unfortunately, while the feature is still in recent 2.[45] kernels, it appears to be broken. The last laptop I installed needed a network card to get working.

Note that using good cable and short runs you can push PPP over the serial ports at 230400bps, and possibly even use the bonding driver (or EQL) to hang several in parallel. I would think that was fast enough for casual use, although PL/IP was faster. I think the parport stuff is the cause, and it may be that only the config info need be changed, I just haven't chased it.

Anyone having a fix or info that there's a workaround, fel free to expand on this!

Signature · 3 lines
bill davidsen <[email protected]>
  CTO, TMR Associates, Inc
Doing interesting things with little computers since 1979.
#3 lore raw
In reply to Paulo J. Matos
Quoted 26 lines · Bill Davidsen
Quoted 8 lines · Paulo J. Matos

I have a LAN at home and know I just got another computer to connect to the LAN, I also found a parallel-parallel cable. The network is ethernet, is it possible to connect the new computer using the parallel ports of the computers to the server of the LAN so that this new computer is able to have access to the internet and the rest of stuff?
What do I need to configure in the kernel?
Is there any how-to out there that answers this question?

There was a protocol called PLIP which did just what you want. I've used it many times for laptop install (Patrick even fixed it in Slackware at my request).

Unfortunately, while the feature is still in recent 2.[45] kernels, it appears to be broken. The last laptop I installed needed a network card to get working.

Note that using good cable and short runs you can push PPP over the serial ports at 230400bps, and possibly even use the bonding driver (or EQL) to hang several in parallel. I would think that was fast enough for casual use, although PL/IP was faster. I think the parport stuff is the cause, and it may be that only the config info need be changed, I just haven't chased it.

Quoted 2 lines

Anyone having a fix or info that there's a workaround, fel free to expand on this!

This was interesting when NIC (network interface cards) cost $100. Nowadays, they are a lot less costly and interest in the PLIP solution has evaporated.

john

#4 lore raw
Quoted 7 lines · John Alvord
Quoted 4 lines · Bill Davidsen

There was a protocol called PLIP which did just what you want. I've used it many times for laptop install (Patrick even fixed it in Slackware at my request).

Quoted 7 lines
Quoted 3 lines

Unfortunately, while the feature is still in recent 2.[45] kernels, it appears to be broken. The last laptop I installed needed a network card to get working.

This was interesting when NIC (network interface cards) cost $100. Nowadays, they are a lot less costly and interest in the PLIP solution has evaporated.

Unless cards now come with their own slot, this is still very useful. A system without parallel is very unusual, while one without network is far more common, and one without a place to even add a network is not that hard to find. While a home user with only a few systems which he can configure at will has no trouble adding a NIC, business use in many places doesn't work that way, and honestly I have a hard time telling someone to buy NICs, cables, a hub, etc, when a $7 cable will work between systems with a functional PL/IP kernel.

Considering the low use things supported in the kernel, I see no reason to think PL/IP is less so. Not a lot of TokenRing out there these days, even in an IBM shop;-)

Signature · 3 lines
bill davidsen <[email protected]>
  CTO, TMR Associates, Inc
Doing interesting things with little computers since 1979.
#5 lore raw
In reply to John Alvord
Quoted 26 lines · Bill Davidsen
Quoted 7 lines · John Alvord
Quoted 4 lines · Bill Davidsen

There was a protocol called PLIP which did just what you want. I've used it many times for laptop install (Patrick even fixed it in Slackware at my request).

Quoted 7 lines
Quoted 3 lines

Unfortunately, while the feature is still in recent 2.[45] kernels, it appears to be broken. The last laptop I installed needed a network card to get working.

This was interesting when NIC (network interface cards) cost $100. Nowadays, they are a lot less costly and interest in the PLIP solution has evaporated.

Unless cards now come with their own slot, this is still very useful. A system without parallel is very unusual, while one without network is far more common, and one without a place to even add a network is not that hard to find. While a home user with only a few systems which he can configure at will has no trouble adding a NIC, business use in many places doesn't work that way, and honestly I have a hard time telling someone to buy NICs, cables, a hub, etc, when a $7 cable will work between systems with a functional PL/IP kernel.

Quoted 3 lines

Considering the low use things supported in the kernel, I see no reason to think PL/IP is less so. Not a lot of TokenRing out there these days, even in an IBM shop;-)

I guess the only remaining problem is finding someone to support the code as Linux winds its way onward through the years. Or someone paying to do that work.

john