Skip to contentSkip to conversation

gcc-3.2 experimental debs

parisc-linux Joel Soete 5 participants 10 messages Apr 21, 2002 – Apr 24, 2002

lore
Share & tools
lore

Joel Soete

author
#0 lore raw

Hi Randolph,

I try my hown gcc-3.2 (+ binutils, glibc) against kernel 2.4.18-pa19 (not yet take the risc with pa20).

It compiles as well as with gcc3.0.x. It boots also but as soon as I try to connect it remotly with telnet or ssh (I forget to test ftp) the system crash:
"Stack pointer and cr30 do not correspond!
Dumping virtual address stack instead

Dumping Stack from ... to ...:

...

[those tree line seems to be repeated infinitely. well after 5 minutes I had to unplug the power supply to reboot]

Humm as it appends as well with telnet as ssh I suspect a inetd problem?

Any idea?

Thanks,
Joel

PS: I will try your dpkg asap

#1 lore raw
Quoted 6 lines · Joel Soete

"Stack pointer and cr30 do not correspond!
Dumping virtual address stack instead

Dumping Stack from ... to ...:

Humm as it appends as well with telnet as ssh I suspect a inetd problem?

I'd bet on gcc-3.2 miscompiling something in the network part of the kernel, personally.

Signature · 1 line
Revolutions do not require corporate support.
#2 lore raw
Quoted 10 lines
Quoted 6 lines

"Stack pointer and cr30 do not correspond!
Dumping virtual address stack instead

Dumping Stack from ... to ...:

Humm as it appends as well with telnet as ssh I suspect a inetd problem?

I'd bet on gcc-3.2 miscompiling something in the network part of the kernel, personally.

Tested today.

Happens in the 3.1 main branch aswell (don't remember it previously happening). Maybe I shouldn't be recommending the use of 3.1 as a cross compiler? ;)

I'll kdb on a serial tommorow morning and see what is causing it to die.

Oddly enough, I run diskless systems and they run off NFS perfectly fine... so everything can't be that broke.

c.

#3 lore raw

Hello Carlos,

Quoting "Carlos O'Donell Jr." <[email protected]>:

Quoted 13 lines
Quoted 6 lines
Quoted 6 lines

"Stack pointer and cr30 do not correspond!
Dumping virtual address stack instead

Dumping Stack from ... to ...:

Humm as it appends as well with telnet as ssh I suspect a inetd

problem?

Quoted 2 lines

I'd bet on gcc-3.2 miscompiling something in the network part of the

kernel,

Quoted 2 lines

personally.

Quoted 6 lines

Tested today.

Happens in the 3.1 main branch aswell (don't remember it previously happening).
Maybe I shouldn't be recommending the use of 3.1 as a cross compiler? ;)

I also notice it on 3.1 about two mount ago (that is why I do another try with 3.2)

Quoted 4 lines

I'll kdb on a serial tommorow morning and see what is causing it to die.

I would also to do so. But I had the bad idea to co the last gcc release (yesterday and today) to rebuild the toolchain.
But gcc build seems to be broken (step 4.2 of your procedure):

gcc -c -DIN_GCC -g -O2 -W -Wall -Wwrite-strings -Wstrict-prototypes
-Wmissing-prototypes -DHAVE_CONFIG_H -I. -Ijava
-I/GNU-Dev/parisc-linux/src/gcc/gcc -I/GNU-Dev/parisc-linux/src/gcc/gcc/java -I/GNU-Dev/parisc-linux/src/gcc/gcc/config -I/GNU-Dev/parisc-linux/src/gcc/gcc/../include /GNU-Dev/parisc-linux/src/gcc/gcc/java/parse.c -o java/parse.o /tmp/ccj2Nlrs.s: Assembler messages:
/tmp/ccj2Nlrs.s:148746: Error: Field out of range [-262144..262143] (-263392). make[1]: *** [java/parse.o] Error 1
make[1]: Leaving directory `/GNU-Dev/parisc-linux/build/gcc/gcc'
make: *** [all-gcc] Error 2

Last week co did not try to build any java.
Any idea or work-around?

Joel

PS1: about step 4.2 of your howto-xc, I notice a small difference between html and pdf (in html you use gcc option "enable-shared" in pdf "disable-shared"). But this not the cause of the above problem.

PS2: I also make an apt-get dist-upgrade (with ftp.de.debian.org) so that native gcc is now 3.0.4-5 (I think it was already installed last week)

-------------------------------------------------
This mail sent through Tiscali Webmail (http://webmail.tiscali.be)

#4 lore raw
Quoted 16 lines

I would also to do so. But I had the bad idea to co the last gcc release (yesterday and today) to rebuild the toolchain.
But gcc build seems to be broken (step 4.2 of your procedure):

gcc -c -DIN_GCC -g -O2 -W -Wall -Wwrite-strings -Wstrict-prototypes

(quoted diff) +0 -4
-Wmissing-prototypes   -DHAVE_CONFIG_H    -I. -Ijava
-I/GNU-Dev/parisc-linux/src/gcc/gcc -I/GNU-Dev/parisc-linux/src/gcc/gcc/java
-I/GNU-Dev/parisc-linux/src/gcc/gcc/config
-I/GNU-Dev/parisc-linux/src/gcc/gcc/../include

/GNU-Dev/parisc-linux/src/gcc/gcc/java/parse.c -o java/parse.o /tmp/ccj2Nlrs.s: Assembler messages:
/tmp/ccj2Nlrs.s:148746: Error: Field out of range [-262144..262143] (-263392). make[1]: *** [java/parse.o] Error 1
make[1]: Leaving directory `/GNU-Dev/parisc-linux/build/gcc/gcc'
make: *** [all-gcc] Error 2

Quoted 2 lines

Last week co did not try to build any java.
Any idea or work-around?

"make bootstrap".

Dave

Signature · 2 lines
J. David Anglin                                  [email protected]
National Research Council of Canada              (613) 990-0752 (FAX: 952-6605)
#5 lore raw
In reply to [email protected]
Quoted 11 lines

Joel

PS1: about step 4.2 of your howto-xc, I notice a small difference between html and pdf (in html you use gcc option "enable-shared" in pdf "disable-shared"). But this not the cause of the above problem.

PS2: I also make an apt-get dist-upgrade (with ftp.de.debian.org) so that native gcc is now 3.0.4-5 (I think it was already installed last week)

Both the HTML and PDF version are the same (just double checked).

http://www.baldric.uwo.ca/~carlos/HOWTO-Parisc/index.html
http://www.baldric.uwo.ca/~carlos/HOWTO-Parisc/HOWTO-Building_PARISC-LINUX_CrossCompiler.pdf

In section 4.2 you are bootstraping the C compiler without glibc so you must use --disable-shared.

In section 4.5 you have already built glibc and you can turn shared support back on with --enable-shared.

c.

p.s. The HTML and PDF do have some formatting differences...

     I'll get around to making them look similar later :}
     Dang... just noticed I missed one of the path changes in
     the pdf...
#6 lore raw

Quoting "Carlos O'Donell Jr." <[email protected]>:

Quoted 10 lines
Quoted 4 lines

Joel

PS1: about step 4.2 of your howto-xc, I notice a small difference

between html

Quoted 1 line

and pdf (in html you use gcc option "enable-shared" in pdf

"disable-shared").

Quoted 3 lines

But this not the cause of the above problem.

PS2: I also make an apt-get dist-upgrade (with ftp.de.debian.org) so

Quoted 9 lines

that native

Quoted 3 lines

gcc is now 3.0.4-5 (I think it was already installed last week)

Both the HTML and PDF version are the same (just double checked).

http://www.baldric.uwo.ca/~carlos/HOWTO-Parisc/index.html

http://www.baldric.uwo.ca/~carlos/HOWTO-Parisc/HOWTO-Building_PARISC-LINUX_CrossCompiler.pdf

Quoted 8 lines

In section 4.2 you are bootstraping the C compiler without glibc so you must use --disable-shared.

In section 4.5 you have already built glibc and you can turn shared support back on with --enable-shared.

c.

Yes you have right (as it is my html which was wrong I do have forgot to 'reload' the page). Sorry for confusion.

Thanks also for explanation and attention.
Joel

Quoted 7 lines

p.s. The HTML and PDF do have some formatting differences...

     I'll get around to making them look similar later :}
     Dang... just noticed I missed one of the path changes in
     the pdf...

-------------------------------------------------
This mail sent through Tiscali Webmail (http://webmail.tiscali.be)

#7 lore raw
In reply to [email protected]

Quoting [email protected]:

Quoted 7 lines

gcc -c -DIN_GCC -g -O2 -W -Wall -Wwrite-strings -Wstrict-prototypes

(quoted diff) +0 -5
-Wmissing-prototypes   -DHAVE_CONFIG_H    -I. -Ijava
-I/GNU-Dev/parisc-linux/src/gcc/gcc
-I/GNU-Dev/parisc-linux/src/gcc/gcc/java
-I/GNU-Dev/parisc-linux/src/gcc/gcc/config
-I/GNU-Dev/parisc-linux/src/gcc/gcc/../include
Quoted 7 lines

/GNU-Dev/parisc-linux/src/gcc/gcc/java/parse.c -o java/parse.o /tmp/ccj2Nlrs.s: Assembler messages:
/tmp/ccj2Nlrs.s:148746: Error: Field out of range [-262144..262143] (-263392).
make[1]: *** [java/parse.o] Error 1
make[1]: Leaving directory `/GNU-Dev/parisc-linux/build/gcc/gcc'
make: *** [all-gcc] Error 2

Forget. The actual problem was again typo: in configure step I type 'enable-langages=c' in place of 'enable-languages=c' (lack of a u between g & a).

Sorry for mistakes.
Joel

-------------------------------------------------
This mail sent through Tiscali Webmail (http://webmail.tiscali.be)

#8 lore raw
In reply to Joel Soete
Quoted 6 lines

I try my hown gcc-3.2 (+ binutils, glibc) against kernel 2.4.18-pa19 (not yet take the risc with pa20).

It compiles as well as with gcc3.0.x. It boots also but as soon as I try to connect it remotly with telnet or ssh (I forget to test ftp) the system crash:

if you still feel adventurous, check out the kdb cvs branch of the kernel and you'll at least be able to tell where it crashed... :-)

randolph

#9 lore raw

Quoting Randolph Chung <[email protected]>:

Quoted 4 lines
Quoted 4 lines

I try my hown gcc-3.2 (+ binutils, glibc) against kernel 2.4.18-pa19 (not yet take the risc with pa20).

It compiles as well as with gcc3.0.x. It boots also but as soon as I

Quoted 10 lines

try

Quoted 2 lines

to connect it remotly with telnet or ssh (I forget to test ftp) the system crash:

if you still feel adventurous, check out the kdb cvs branch of the kernel and you'll at least be able to tell where it crashed... :-)

randolph

Yes I will also try (and find out howto use)

Joel

-------------------------------------------------
This mail sent through Tiscali Webmail (http://webmail.tiscali.be)