Skip to contentSkip to conversation

HDSP CardBus issue - lspci -vv output

DISCUSSION Thomas Charbonnel 3 participants 3 messages May 17, 2002 – May 18, 2002

lore
Share & tools
lore
#0 lore raw

Paul, here are the results of the commands you asked.
One strange thing with my particular laptop is that IRQ 10 seems widely shared.

Thomas

Without the card lspci -vv gives:

00:00.0 Host bridge: Intel Corp.: Unknown device 3575 (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

        Latency: 0
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [40] #09 [0105]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
                Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corp.: Unknown device 3576 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 96
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        Memory behind bridge: d1000000-d1ffffff
        Prefetchable memory behind bridge: f0000000-f7ffffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1d.0 USB Controller: Intel Corp.: Unknown device 2482 (rev 01) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1800 [size=32]

00:1d.1 USB Controller: Intel Corp.: Unknown device 2484 (rev 01) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1820 [size=32]

00:1d.2 USB Controller: Intel Corp.: Unknown device 2487 (rev 01) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at 1840 [size=32]

00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (-M) (rev
41) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: d2000000-d20fffff
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp.: Unknown device 248c (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:1f.1 IDE interface: Intel Corp.: Unknown device 248a (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 0
        Interrupt: pin A routed to IRQ 5
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374
        Region 4: I/O ports at 1860 [size=16]
        Region 5: Memory at d0000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corp.: Unknown device 2483 (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 1880 [size=32]

00:1f.5 Multimedia audio controller: Intel Corp. AC'97 Audio Controller (rev
01) Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Interrupt: pin B routed to IRQ 10
        Region 0: I/O ports at 1c00 [size=256]
        Region 1: I/O ports at 18c0 [size=64]

00:1f.6 Modem: Intel Corp.: Unknown device 2486 (rev 01) (prog-if 00
[Generic]) Subsystem: Toshiba America Info Systems: Unknown device
0001
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Interrupt: pin B routed to IRQ 10
        Region 0: I/O ports at 2400 [size=256]
        Region 1: I/O ports at 2000 [size=128]

01:00.0 VGA compatible controller: nVidia Corporation GeForce2 Go (rev b2) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>

02:00.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8023 (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d2004000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at d2004800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:04.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d2005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001

02:04.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 10
Region 0: Memory at d2006000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001

02:06.0 System peripheral: Toshiba America Info Systems: Unknown device 0804 (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 0: Memory at d2004c00 (32-bit, non-prefetchable) [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1+,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

With the card inserted:

00:00.0 Host bridge: Intel Corp.: Unknown device 3575 (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

        Latency: 0
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [40] #09 [0105]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
                Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corp.: Unknown device 3576 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 96
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        Memory behind bridge: d1000000-d1ffffff
        Prefetchable memory behind bridge: f0000000-f7ffffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1d.0 USB Controller: Intel Corp.: Unknown device 2482 (rev 01) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1800 [size=32]

00:1d.1 USB Controller: Intel Corp.: Unknown device 2484 (rev 01) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1820 [size=32]

00:1d.2 USB Controller: Intel Corp.: Unknown device 2487 (rev 01) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at 1840 [size=32]

00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (-M) (rev
41) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: d2000000-d20fffff
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp.: Unknown device 248c (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:1f.1 IDE interface: Intel Corp.: Unknown device 248a (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 0
        Interrupt: pin A routed to IRQ 5
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374
        Region 4: I/O ports at 1860 [size=16]
        Region 5: Memory at d0000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corp.: Unknown device 2483 (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 1880 [size=32]

00:1f.5 Multimedia audio controller: Intel Corp. AC'97 Audio Controller (rev
01) Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Interrupt: pin B routed to IRQ 10
        Region 0: I/O ports at 1c00 [size=256]
        Region 1: I/O ports at 18c0 [size=64]

00:1f.6 Modem: Intel Corp.: Unknown device 2486 (rev 01) (prog-if 00
[Generic]) Subsystem: Toshiba America Info Systems: Unknown device
0001
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Interrupt: pin B routed to IRQ 10
        Region 0: I/O ports at 2400 [size=256]
        Region 1: I/O ports at 2000 [size=128]

01:00.0 VGA compatible controller: nVidia Corporation GeForce2 Go (rev b2) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>

02:00.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8023 (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d2004000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at d2004800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:04.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d2005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001

02:04.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 10
Region 0: Memory at d2006000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001

02:06.0 System peripheral: Toshiba America Info Systems: Unknown device 0804 (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device ff00
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 0: Memory at d2004c00 (32-bit, non-prefetchable) [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1+,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:00.0 Multimedia audio controller: Xilinx, Inc.: Unknown device 3fc5 (rev 0a)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: [virtual] Memory at d2400000 (32-bit, non-prefetchable)

_______________________________________________________________

Hundreds of nodes, one monster rendering program.
Now that’s a super model! Visit http://clustering.foundries.sf.net/

#1 lore raw
Quoted 3 lines · Thomas Charbonnel

Paul, here are the results of the commands you asked.
One strange thing with my particular laptop is that IRQ 10 seems widely shared.

that's usually due to ACPI .. I've seen this all over the place, but it generally doesn't seem to cause any problems ..

later,
Steve

_______________________________________________________________

Hundreds of nodes, one monster rendering program.
Now that’s a super model! Visit http://clustering.foundries.sf.net/

#2 lore raw
In reply to Thomas Charbonnel
Quoted 3 lines

Paul, here are the results of the commands you asked.
One strange thing with my particular laptop is that IRQ 10 seems widely shared.

ok, now i'd like to see the contents of /proc/ioports and /proc/iomem before and after card insertion.

--p

_______________________________________________________________
Hundreds of nodes, one monster rendering program.
Now that's a super model! Visit http://clustering.foundries.sf.net/