kbd not functioning in 2.5.25-dj2
Same config as in my last post about the issue linking with this kernel. I'm having my keyboard just not respond from boot. I've got Input Device support built in and i had it as module and the keyboard is ps/2. No idea what's going on here
Quoted 5 lines · Ed Sweetman
Same config as in my last post about the issue linking with this kernel. I'm having my keyboard just not respond from boot. I've got Input Device support built in and i had it as module and the keyboard is ps/2. No idea what's going on here
Just a "me too" here.. I've had this problem since around 2.5.15-dj
and later, and have had input and keyboard support compiled into the kernel. Luckily I was able to get into the box via ssh, and check things. both keyboard and mouse are PS/2. If possible, see if you can do this, and check if IRQ 1 is not listed in /proc/interrupts. That is what is happening with me, while my mouse is working. For me to get my keyboard to work, I have to have the following set:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=yCONFIG_INPUT_EVBUG=yCONFIG_SERIO=yCONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_KEYBOARD_XTKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=y
This leaves me without using the new Input API, but with a working
keyboard. with using the new API, mouse will work, keyboard will not. you can try these, and use the old setup (I assume will be made legacy by the time 2.6 comes out), and let me know if they work. The new API seems to be working for some people, but not all.
BL.
Signature · 4 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF
2.5.18 is the last time it worked for me I have basically the same exact config, the new input system seems to have undergone some changes since then though and now it's not behaving. I will try setting the XTKBD setting and PS2SEDKBD or whatever it is.
Quoted 48 lines · A Guy Called Tyketto
Quoted 5 lines · Ed Sweetman
Same config as in my last post about the issue linking with this kernel. I'm having my keyboard just not respond from boot. I've got Input Device support built in and i had it as module and the keyboard is ps/2. No idea what's going on here
Just a "me too" here.. I've had this problem since around 2.5.15-dj
and later, and have had input and keyboard support compiled into the kernel. Luckily I was able to get into the box via ssh, and check things. both keyboard and mouse are PS/2. If possible, see if you can do this, and check if IRQ 1 is not listed in/proc/interrupts. That is what is happening with me, while my mouse is working. For me to get my keyboard to work, I have to have the following set:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=yCONFIG_INPUT_EVBUG=yCONFIG_SERIO=yCONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_KEYBOARD_XTKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=yThis leaves me without using the new Input API, but with a working
keyboard. with using the new API, mouse will work, keyboard will not. you can try these, and use the old setup (I assume will be made legacy by the time 2.6 comes out), and let me know if they work. The new API seems to be working for some people, but not all.BL.Signature · 10 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Nope, failure. I'm not getting any reaction from the kernel at all about the keyboard. I'm including my config
Quoted 57 lines · Ed Sweetman
2.5.18 is the last time it worked for me I have basically the same exact config, the new input system seems to have undergone some changes since then though and now it's not behaving. I will try setting the XTKBD setting and PS2SEDKBD or whatever it is.
Quoted 30 lines · A Guy Called Tyketto
Quoted 5 lines · Ed Sweetman
Same config as in my last post about the issue linking with this kernel. I'm having my keyboard just not respond from boot. I've got Input Device support built in and i had it as module and the keyboard is ps/2. No idea what's going on here
Just a "me too" here.. I've had this problem since around 2.5.15-dj
and later, and have had input and keyboard support compiled into the kernel. Luckily I was able to get into the box via ssh, and check things. both keyboard and mouse are PS/2. If possible, see if you can do this, and check if IRQ 1 is not listed in/proc/interrupts. That is what is happening with me, while my mouse is working. For me to get my keyboard to work, I have to have the following set:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=yCONFIG_INPUT_EVBUG=yCONFIG_SERIO=yCONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_KEYBOARD_XTKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=yQuoted 18 lines
This leaves me without using the new Input API, but with a working
keyboard. with using the new API, mouse will work, keyboard will not. you can try these, and use the old setup (I assume will be made legacy by the time 2.6 comes out), and let me know if they work. The new API seems to be working for some people, but not all.BL.Signature · 10 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
#
# Automatically generated make config: don't edit
#CONFIG_X86=y
# CONFIG_SBUS is not setCONFIG_UID16=y
#
# Code maturity level options
#CONFIG_EXPERIMENTAL=y
#
# General setup
#CONFIG_NET=yCONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not setCONFIG_SYSCTL=y
#
# Loadable module support
#CONFIG_MODULES=y
# CONFIG_MODVERSIONS is not setCONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not setCONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not setCONFIG_X86_WP_WORKS_OK=yCONFIG_X86_INVLPG=yCONFIG_X86_CMPXCHG=yCONFIG_X86_XADD=yCONFIG_X86_BSWAP=yCONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not setCONFIG_RWSEM_XCHGADD_ALGORITHM=yCONFIG_X86_L1_CACHE_SHIFT=7CONFIG_X86_TSC=yCONFIG_X86_GOOD_APIC=yCONFIG_X86_USE_PPRO_CHECKSUM=y
# CONFIG_SMP is not setCONFIG_PREEMPT=yCONFIG_X86_UP_APIC=yCONFIG_X86_UP_IOAPIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_X86_IO_APIC=yCONFIG_X86_MCE=y
# CONFIG_X86_MCE_NONFATAL is not setCONFIG_X86_MCE_P4THERMAL=y
# CONFIG_CPU_FREQ is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not setCONFIG_X86_MSR=mCONFIG_X86_CPUID=mCONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not setCONFIG_MTRR=yCONFIG_HAVE_DEC_LOCK=y
#
# Power management options (ACPI, APM)
#
#
# ACPI Support
#
# CONFIG_ACPI is not set
# CONFIG_PM is not set
# CONFIG_APM is not set
# CONFIG_SOFTWARE_SUSPEND is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not setCONFIG_PCI_GOANY=yCONFIG_PCI_BIOS=yCONFIG_PCI_DIRECT=yCONFIG_PCI_NAMES=y
# CONFIG_ISA is not set
# CONFIG_EISA is not set
# CONFIG_MCA is not setCONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
#
# Executable file formats
#CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not setCONFIG_BINFMT_AOUT=mCONFIG_BINFMT_ELF=yCONFIG_BINFMT_MISC=m
# CONFIG_IKCONFIG is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set
# CONFIG_PNPBIOS is not set
#
# Block devices
#CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not setCONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set
#
# Networking options
#CONFIG_PACKET=yCONFIG_PACKET_MMAP=y
# CONFIG_NETLINK_DEV is not set
# CONFIG_NETFILTER is not set
# CONFIG_FILTER is not setCONFIG_UNIX=yCONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_IPV6 is not set
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
#
# Appletalk devices
#
# CONFIG_DEV_APPLETALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set
#
# ATA/IDE/MFM/RLL support
#CONFIG_IDE=y
# CONFIG_IDE_24 is not setCONFIG_IDE_25=y
#
# ATA and ATAPI Block devices
#CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives #
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set CONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=yCONFIG_IDEDISK_STROKE=y
# CONFIG_BLK_DEV_IDECS is not set CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=m
#
# ATA host chip set support
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
# CONFIG_BLK_DEV_RZ1000 is not set
#
# PCI host chip set support
#
# CONFIG_BLK_DEV_OFFBOARD is not setCONFIG_IDEPCI_SHARE_IRQ=yCONFIG_BLK_DEV_IDEDMA_PCI=yCONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not setCONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_IDE_TCQ_DEFAULT is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_AEC6280_BURST is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not setCONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_SL82C105 is not set
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_IDEDMA_IVB is not setCONFIG_ATAPI=yCONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
#
# SCSI support
#CONFIG_SCSI=m
#
# SCSI support type (disk, tape, CD-ROM)
#
# CONFIG_BROKEN_SCSI_ERROR_HANDLING is not setCONFIG_BLK_DEV_SD=mCONFIG_SD_EXTRA_DEVS=40
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not setCONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not setCONFIG_SR_EXTRA_DEVS=2CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SM is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #CONFIG_SCSI_MULTI_LUN=yCONFIG_SCSI_REPORT_LUNS=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_DEBUG is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Network device support
#CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not setCONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
#
# Ethernet (10 or 100Mbit)
#CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not setCONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not setCONFIG_EEPRO100=mCONFIG_E100=m
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_NEW_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set
#
# Input device support
#CONFIG_INPUT=y
#
# Userland interfaces
#CONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not setCONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not setCONFIG_SOUND_GAMEPORT=y
# CONFIG_GAMEPORT_NS558 is not set
# CONFIG_GAMEPORT_L4 is not set
# CONFIG_GAMEPORT_EMU10K1 is not set
# CONFIG_GAMEPORT_VORTEX is not set
# CONFIG_GAMEPORT_FM801 is not set
# CONFIG_GAMEPORT_CS461X is not setCONFIG_SERIO=y
# CONFIG_SERIO_I8042 is not setCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
#
# Input Device Drivers
#CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_PS2SERKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_JOYSTICK_ANALOG is not set
# CONFIG_JOYSTICK_A3D is not set
# CONFIG_JOYSTICK_ADI is not set
# CONFIG_JOYSTICK_COBRA is not set
# CONFIG_JOYSTICK_GF2K is not set
# CONFIG_JOYSTICK_GRIP is not set
# CONFIG_JOYSTICK_GUILLEMOT is not set
# CONFIG_JOYSTICK_INTERACT is not set
# CONFIG_JOYSTICK_SIDEWINDER is not set
# CONFIG_JOYSTICK_TMDC is not set
# CONFIG_JOYSTICK_IFORCE_USB is not set
# CONFIG_JOYSTICK_IFORCE_232 is not set
# CONFIG_JOYSTICK_WARRIOR is not set
# CONFIG_JOYSTICK_MAGELLAN is not set
# CONFIG_JOYSTICK_SPACEORB is not set
# CONFIG_JOYSTICK_SPACEBALL is not set
# CONFIG_JOYSTICK_STINGER is not set
# CONFIG_JOYSTICK_TWIDDLER is not set
# CONFIG_JOYSTICK_DB9 is not set
# CONFIG_JOYSTICK_GAMECON is not set
# CONFIG_JOYSTICK_TURBOGRAFX is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
#
# Character devices
#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not setCONFIG_UNIX98_PTYS=yCONFIG_UNIX98_PTY_COUNT=256
#
# I2C support
#CONFIG_I2C=mCONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_PHILIPSPAR is not set
# CONFIG_I2C_ELV is not set
# CONFIG_I2C_VELLEMAN is not set
# CONFIG_I2C_ALGOPCF is not setCONFIG_I2C_CHARDEV=mCONFIG_I2C_PROC=m
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_AMD_RNG is not setCONFIG_INTEL_RNG=y
# CONFIG_NVRAM is not setCONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not setCONFIG_AGP=yCONFIG_AGP_INTEL=y
# CONFIG_AGP_I810 is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not setCONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_MWAVE is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_QFMT_V1 is not set
# CONFIG_QFMT_V2 is not set
# CONFIG_AUTOFS_FS is not setCONFIG_AUTOFS4_FS=y
# CONFIG_REISERFS_FS is not set
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not setCONFIG_EXT3_FS=yCONFIG_JBD=y
# CONFIG_JBD_DEBUG is not setCONFIG_FAT_FS=mCONFIG_MSDOS_FS=m
# CONFIG_UMSDOS_FS is not setCONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_TMPFS is not setCONFIG_RAMFS=yCONFIG_ISO9660_FS=mCONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
# CONFIG_JFS_FS is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS_DEBUG is not set
# CONFIG_HPFS_FS is not setCONFIG_PROC_FS=yCONFIG_DEVFS_FS=yCONFIG_DEVFS_MOUNT=y
# CONFIG_DEVFS_DEBUG is not set
# CONFIG_DEVPTS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not setCONFIG_EXT2_FS=m
# CONFIG_SYSV_FS is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_NFS_FS is not set
# CONFIG_NFS_V3 is not set
# CONFIG_ROOT_NFS is not set
# CONFIG_NFSD is not set
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
# CONFIG_SUNRPC is not set
# CONFIG_LOCKD is not set
# CONFIG_EXPORTFS is not setCONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
# CONFIG_ZISOFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not setCONFIG_MSDOS_PARTITION=yCONFIG_SMB_NLS=yCONFIG_NLS=y
#
# Native Language Support
#CONFIG_NLS_DEFAULT="iso8859-1"CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not setCONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Console drivers
#CONFIG_VGA_CONSOLE=yCONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
# CONFIG_FB is not set
#
# Sound
#CONFIG_SOUND=m
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# Advanced Linux Sound Architecture
#CONFIG_SND=m
# CONFIG_SND_SEQUENCER is not setCONFIG_SND_OSSEMUL=yCONFIG_SND_MIXER_OSS=mCONFIG_SND_PCM_OSS=m
# CONFIG_SND_SEQUENCER_OSS is not setCONFIG_SND_RTCTIMER=m
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
# CONFIG_SND_DEBUG_MEMORY is not set
# CONFIG_SND_DEBUG_DETECT is not set
#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_CS46XX is not setCONFIG_SND_EMU10K1=m
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA686 is not set
# CONFIG_SND_VIA8233 is not set
#
# USB support
#CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#CONFIG_USB_DEVICEFS=yCONFIG_USB_LONG_TIMEOUT=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_EHCI_HCD is not set
# CONFIG_USB_OHCI_HCD is not setCONFIG_USB_UHCI_HCD_ALT=m
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not setCONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
#
# USB Human Interface Devices (HID)
#CONFIG_USB_HID=mCONFIG_USB_HIDINPUT=y
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_PWC is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_STV680 is not set
#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19QW is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19QI is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SAFE_PADDED is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_BRLVGER is not set
#
# Bluetooth support
#
# CONFIG_BLUEZ is not set
#
# Kernel hacking
#CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_OBSOLETE is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_IOVIRT is not setCONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_486_STRING is not set
# CONFIG_FRAME_POINTER is not set
#
# Library routines
#CONFIG_CRC32=y
# CONFIG_ZLIB_INFLATE is not set
# CONFIG_ZLIB_DEFLATE is not set
Hi!
Okay, I wrote all these input drivers. So I'd like to see them working. ;)
All you should need for proper function of both keyboard and mouse on a all-input-driver based system (like -dj kernels, or linux-input BK tree are) is:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_SERIO=yCONFIG_SERIO_I8042=yCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=y
So I guess your problem is not enabling the i8042 module.
This code will also hopefully be enabled in 2.5.26 (though it'll be optional with the old driver still there).
Quoted 1,092 lines · Ed Sweetman
Nope, failure. I'm not getting any reaction from the kernel at all about the keyboard. I'm including my config
Quoted 57 lines · Ed Sweetman
2.5.18 is the last time it worked for me I have basically the same exact config, the new input system seems to have undergone some changes since then though and now it's not behaving. I will try setting the XTKBD setting and PS2SEDKBD or whatever it is.
Quoted 30 lines · A Guy Called Tyketto
Quoted 5 lines · Ed Sweetman
Same config as in my last post about the issue linking with this kernel. I'm having my keyboard just not respond from boot. I've got Input Device support built in and i had it as module and the keyboard is ps/2. No idea what's going on here
Just a "me too" here.. I've had this problem since around 2.5.15-dj
and later, and have had input and keyboard support compiled into the kernel. Luckily I was able to get into the box via ssh, and check things. both keyboard and mouse are PS/2. If possible, see if you can do this, and check if IRQ 1 is not listed in/proc/interrupts. That is what is happening with me, while my mouse is working. For me to get my keyboard to work, I have to have the following set:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=yCONFIG_INPUT_EVBUG=yCONFIG_SERIO=yCONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_KEYBOARD_XTKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=yQuoted 18 lines
This leaves me without using the new Input API, but with a working
keyboard. with using the new API, mouse will work, keyboard will not. you can try these, and use the old setup (I assume will be made legacy by the time 2.6 comes out), and let me know if they work. The new API seems to be working for some people, but not all.BL.Signature · 10 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/Quoted 5 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/#
# Automatically generated make config: don't edit
#CONFIG_X86=y
#CONFIG_SBUSis not setCONFIG_UID16=y#
# Code maturity level options
#CONFIG_EXPERIMENTAL=y#
# General setup
#CONFIG_NET=yCONFIG_SYSVIPC=y
#CONFIG_BSD_PROCESS_ACCTis not setCONFIG_SYSCTL=y#
# Loadable module support
#CONFIG_MODULES=y
#CONFIG_MODVERSIONSis not setCONFIG_KMOD=y#
# Processor type and features
#
#CONFIG_M386is not set
#CONFIG_M486is not set
#CONFIG_M586is not set
#CONFIG_M586TSCis not set
#CONFIG_M586MMXis not set
#CONFIG_M686is not set
#CONFIG_MPENTIUMIIIis not setCONFIG_MPENTIUM4=y
#CONFIG_MK6is not set
#CONFIG_MK7is not set
#CONFIG_MELANis not set
#CONFIG_MCRUSOEis not set
#CONFIG_MWINCHIPC6is not set
#CONFIG_MWINCHIP2is not set
#CONFIG_MWINCHIP3Dis not set
#CONFIG_MCYRIXIIIis not setCONFIG_X86_WP_WORKS_OK=yCONFIG_X86_INVLPG=yCONFIG_X86_CMPXCHG=yCONFIG_X86_XADD=yCONFIG_X86_BSWAP=yCONFIG_X86_POPAD_OK=y
#CONFIG_RWSEM_GENERIC_SPINLOCKis not setCONFIG_RWSEM_XCHGADD_ALGORITHM=yCONFIG_X86_L1_CACHE_SHIFT=7CONFIG_X86_TSC=yCONFIG_X86_GOOD_APIC=yCONFIG_X86_USE_PPRO_CHECKSUM=y
#CONFIG_SMPis not setCONFIG_PREEMPT=yCONFIG_X86_UP_APIC=yCONFIG_X86_UP_IOAPIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_X86_IO_APIC=yCONFIG_X86_MCE=y
#CONFIG_X86_MCE_NONFATALis not setCONFIG_X86_MCE_P4THERMAL=y
#CONFIG_CPU_FREQis not set
#CONFIG_TOSHIBAis not set
#CONFIG_I8Kis not set
#CONFIG_MICROCODEis not setCONFIG_X86_MSR=mCONFIG_X86_CPUID=mCONFIG_NOHIGHMEM=y
#CONFIG_HIGHMEM4Gis not set
#CONFIG_HIGHMEM64Gis not set
#CONFIG_MATH_EMULATIONis not setCONFIG_MTRR=yCONFIG_HAVE_DEC_LOCK=y#
# Power management options (ACPI, APM)
##
# ACPI Support
#
#CONFIG_ACPIis not set
#CONFIG_PMis not set
#CONFIG_APMis not set
#CONFIG_SOFTWARE_SUSPENDis not set#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#CONFIG_PCI=y
#CONFIG_PCI_GOBIOSis not set
#CONFIG_PCI_GODIRECTis not setCONFIG_PCI_GOANY=yCONFIG_PCI_BIOS=yCONFIG_PCI_DIRECT=yCONFIG_PCI_NAMES=y
#CONFIG_ISAis not set
#CONFIG_EISAis not set
#CONFIG_MCAis not setCONFIG_HOTPLUG=y#
# PCMCIA/CardBus support
#
#CONFIG_PCMCIAis not set#
# PCI Hotplug Support
#
#CONFIG_HOTPLUG_PCIis not set
#CONFIG_HOTPLUG_PCI_COMPAQis not set
#CONFIG_HOTPLUG_PCI_COMPAQ_NVRAMis not set
#CONFIG_HOTPLUG_PCI_IBMis not set#
# Executable file formats
#CONFIG_KCORE_ELF=y
#CONFIG_KCORE_AOUTis not setCONFIG_BINFMT_AOUT=mCONFIG_BINFMT_ELF=yCONFIG_BINFMT_MISC=m
#CONFIG_IKCONFIGis not set#
# Memory Technology Devices (MTD)
#
#CONFIG_MTDis not set#
# Parallel port support
#
#CONFIG_PARPORTis not set#
# Plug and Play configuration
#
#CONFIG_PNPis not set
#CONFIG_ISAPNPis not set
#CONFIG_PNPBIOSis not set#
# Block devices
#CONFIG_BLK_DEV_FD=y
#CONFIG_BLK_DEV_XDis not set
#CONFIG_PARIDEis not set
#CONFIG_BLK_CPQ_DAis not set
#CONFIG_BLK_CPQ_CISS_DAis not set
#CONFIG_CISS_SCSI_TAPEis not set
#CONFIG_BLK_DEV_DAC960is not set
#CONFIG_BLK_DEV_UMEMis not setCONFIG_BLK_DEV_LOOP=m
#CONFIG_BLK_DEV_NBDis not set
#CONFIG_BLK_DEV_RAMis not set
#CONFIG_BLK_DEV_INITRDis not set#
# Multi-device support (RAID and LVM)
#
#CONFIG_MDis not set
#CONFIG_BLK_DEV_MDis not set
#CONFIG_MD_LINEARis not set
#CONFIG_MD_RAID0is not set
#CONFIG_MD_RAID1is not set
#CONFIG_MD_RAID5is not set
#CONFIG_MD_MULTIPATHis not set
#CONFIG_BLK_DEV_LVMis not set#
# Networking options
#CONFIG_PACKET=yCONFIG_PACKET_MMAP=y
#CONFIG_NETLINK_DEVis not set
#CONFIG_NETFILTERis not set
#CONFIG_FILTERis not setCONFIG_UNIX=yCONFIG_INET=y
#CONFIG_IP_MULTICASTis not set
#CONFIG_IP_ADVANCED_ROUTERis not set
#CONFIG_IP_PNPis not set
#CONFIG_NET_IPIPis not set
#CONFIG_NET_IPGREis not set
#CONFIG_ARPDis not set
#CONFIG_INET_ECNis not set
#CONFIG_SYN_COOKIESis not set
#CONFIG_IPV6is not set
#CONFIG_KHTTPDis not set
#CONFIG_ATMis not set
#CONFIG_VLAN_8021Qis not set#
#
#
#CONFIG_IPXis not set
#CONFIG_ATALKis not set#
# Appletalk devices
#
#CONFIG_DEV_APPLETALKis not set
#CONFIG_DECNETis not set
#CONFIG_BRIDGEis not set
#CONFIG_X25is not set
#CONFIG_LAPBis not set
#CONFIG_LLCis not set
#CONFIG_NET_DIVERTis not set
#CONFIG_ECONETis not set
#CONFIG_WAN_ROUTERis not set
#CONFIG_NET_FASTROUTEis not set
#CONFIG_NET_HW_FLOWCONTROLis not set#
# QoS and/or fair queueing
#
#CONFIG_NET_SCHEDis not set#
# Telephony Support
#
#CONFIG_PHONEis not set
#CONFIG_PHONE_IXJis not set
#CONFIG_PHONE_IXJ_PCMCIAis not set#
# ATA/IDE/MFM/RLL support
#CONFIG_IDE=y
#CONFIG_IDE_24is not setCONFIG_IDE_25=y#
# ATA and ATAPI Block devices
#CONFIG_BLK_DEV_IDE=y#
# Please seeDocumentation/ide.txtfor help/info on IDE drives #
#CONFIG_BLK_DEV_HD_IDEis not set
#CONFIG_BLK_DEV_HDis not setCONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=yCONFIG_IDEDISK_STROKE=y
#CONFIG_BLK_DEV_IDECSis not setCONFIG_BLK_DEV_IDECD=m
#CONFIG_BLK_DEV_IDETAPEis not set
#CONFIG_BLK_DEV_IDEFLOPPYis not setCONFIG_BLK_DEV_IDESCSI=m#
# ATA host chip set support
#
#CONFIG_BLK_DEV_CMD640is not set
#CONFIG_BLK_DEV_CMD640_ENHANCEDis not set
#CONFIG_BLK_DEV_ISAPNPis not set
#CONFIG_BLK_DEV_RZ1000is not set#
# PCI host chip set support
#
#CONFIG_BLK_DEV_OFFBOARDis not setCONFIG_IDEPCI_SHARE_IRQ=yCONFIG_BLK_DEV_IDEDMA_PCI=yCONFIG_IDEDMA_PCI_AUTO=y
#CONFIG_IDEDMA_ONLYDISKis not setCONFIG_BLK_DEV_IDEDMA=y
#CONFIG_BLK_DEV_IDE_TCQis not set
#CONFIG_BLK_DEV_IDE_TCQ_DEFAULTis not set
#CONFIG_IDEDMA_NEW_DRIVE_LISTINGSis not set
#CONFIG_BLK_DEV_AEC62XXis not set
#CONFIG_AEC6280_BURSTis not set
#CONFIG_BLK_DEV_ALI15X3is not set
#CONFIG_WDC_ALI15X3is not set
#CONFIG_BLK_DEV_AMD74XXis not set
#CONFIG_BLK_DEV_CMD64Xis not set
#CONFIG_BLK_DEV_CY82C693is not set
#CONFIG_BLK_DEV_CS5530is not set
#CONFIG_BLK_DEV_HPT34Xis not set
#CONFIG_HPT34X_AUTODMAis not set
#CONFIG_BLK_DEV_HPT366is not setCONFIG_BLK_DEV_PIIX=y
#CONFIG_BLK_DEV_NS87415is not set
#CONFIG_BLK_DEV_OPTI621is not set
#CONFIG_BLK_DEV_PDC202XXis not set
#CONFIG_PDC202XX_BURSTis not set
#CONFIG_PDC202XX_FORCEis not set
#CONFIG_BLK_DEV_SVWKSis not set
#CONFIG_BLK_DEV_SIS5513is not set
#CONFIG_BLK_DEV_TRM290is not set
#CONFIG_BLK_DEV_VIA82CXXXis not set
#CONFIG_BLK_DEV_SL82C105is not set
#CONFIG_IDE_CHIPSETSis not set
#CONFIG_IDEDMA_IVBis not setCONFIG_ATAPI=yCONFIG_IDEDMA_AUTO=y
#CONFIG_BLK_DEV_ATARAIDis not set
#CONFIG_BLK_DEV_ATARAID_PDCis not set
#CONFIG_BLK_DEV_ATARAID_HPTis not set#
# SCSI support
#CONFIG_SCSI=m#
# SCSI support type (disk, tape, CD-ROM)
#
#CONFIG_BROKEN_SCSI_ERROR_HANDLINGis not setCONFIG_BLK_DEV_SD=mCONFIG_SD_EXTRA_DEVS=40
#CONFIG_CHR_DEV_STis not set
#CONFIG_CHR_DEV_OSSTis not setCONFIG_BLK_DEV_SR=m
#CONFIG_BLK_DEV_SR_VENDORis not setCONFIG_SR_EXTRA_DEVS=2CONFIG_CHR_DEV_SG=m
#CONFIG_CHR_DEV_SMis not set#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #CONFIG_SCSI_MULTI_LUN=yCONFIG_SCSI_REPORT_LUNS=y
#CONFIG_SCSI_CONSTANTSis not set
#CONFIG_SCSI_LOGGINGis not set#
# SCSI low-level drivers
#
#CONFIG_BLK_DEV_3W_XXXX_RAIDis not set
#CONFIG_SCSI_7000FASSTis not set
#CONFIG_SCSI_ACARDis not set
#CONFIG_SCSI_AIC7XXXis not set
#CONFIG_SCSI_AIC7XXX_OLDis not set
#CONFIG_SCSI_DPT_I2Ois not set
#CONFIG_SCSI_ADVANSYSis not set
#CONFIG_SCSI_IN2000is not set
#CONFIG_SCSI_AM53C974is not set
#CONFIG_SCSI_MEGARAIDis not set
#CONFIG_SCSI_BUSLOGICis not set
#CONFIG_SCSI_CPQFCTSis not set
#CONFIG_SCSI_DMX3191Dis not set
#CONFIG_SCSI_DTC3280is not set
#CONFIG_SCSI_EATAis not set
#CONFIG_SCSI_EATA_DMAis not set
#CONFIG_SCSI_EATA_PIOis not set
#CONFIG_SCSI_FUTURE_DOMAINis not set
#CONFIG_SCSI_GDTHis not set
#CONFIG_SCSI_GENERIC_NCR5380is not set
#CONFIG_SCSI_IPSis not set
#CONFIG_SCSI_INITIOis not set
#CONFIG_SCSI_INIA100is not set
#CONFIG_SCSI_NCR53C406Ais not set
#CONFIG_SCSI_NCR53C7xxis not set
#CONFIG_SCSI_SYM53C8XX_2is not set
#CONFIG_SCSI_NCR53C8XXis not set
#CONFIG_SCSI_SYM53C8XXis not set
#CONFIG_SCSI_PAS16is not set
#CONFIG_SCSI_PCI2000is not set
#CONFIG_SCSI_PCI2220Iis not set
#CONFIG_SCSI_PSI240Iis not set
#CONFIG_SCSI_QLOGIC_FASis not set
#CONFIG_SCSI_QLOGIC_ISPis not set
#CONFIG_SCSI_QLOGIC_FCis not set
#CONFIG_SCSI_QLOGIC_1280is not set
#CONFIG_SCSI_SYM53C416is not set
#CONFIG_SCSI_DC390Tis not set
#CONFIG_SCSI_T128is not set
#CONFIG_SCSI_U14_34Fis not set
#CONFIG_SCSI_DEBUGis not set#
# Fusion MPT device support
#
#CONFIG_FUSIONis not set
#CONFIG_FUSION_BOOTis not set
#CONFIG_FUSION_ISENSEis not set
#CONFIG_FUSION_CTLis not set
#CONFIG_FUSION_LANis not set#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
#CONFIG_IEEE1394is not set#
# I2O device support
#
#CONFIG_I2Ois not set
#CONFIG_I2O_PCIis not set
#CONFIG_I2O_BLOCKis not set
#CONFIG_I2O_LANis not set
#CONFIG_I2O_SCSIis not set
#CONFIG_I2O_PROCis not set#
# Network device support
#CONFIG_NETDEVICES=y#
# ARCnet devices
#
#CONFIG_ARCNETis not setCONFIG_DUMMY=m
#CONFIG_BONDINGis not set
#CONFIG_EQUALIZERis not set
#CONFIG_TUNis not set
#CONFIG_ETHERTAPis not set#
# Ethernet (10 or 100Mbit)
#CONFIG_NET_ETHERNET=y
#CONFIG_SUNLANCEis not set
#CONFIG_HAPPYMEALis not set
#CONFIG_SUNBMACis not set
#CONFIG_SUNQEis not set
#CONFIG_SUNGEMis not set
#CONFIG_NET_VENDOR_3COMis not set
#CONFIG_LANCEis not set
#CONFIG_NET_VENDOR_SMCis not set
#CONFIG_NET_VENDOR_RACALis not set
#CONFIG_HP100is not set
#CONFIG_NET_ISAis not setCONFIG_NET_PCI=y
#CONFIG_PCNET32is not set
#CONFIG_ADAPTEC_STARFIREis not set
#CONFIG_APRICOTis not set
#CONFIG_CS89x0is not set
#CONFIG_DGRSis not setCONFIG_EEPRO100=mCONFIG_E100=m
#CONFIG_LNE390is not set
#CONFIG_FEALNXis not set
#CONFIG_NATSEMIis not set
#CONFIG_NE2K_PCIis not set
#CONFIG_NE3210is not set
#CONFIG_ES3210is not set
#CONFIG_8139CPis not set
#CONFIG_8139TOOis not set
#CONFIG_8139TOO_PIOis not set
#CONFIG_8139TOO_TUNE_TWISTERis not set
#CONFIG_8139TOO_8129is not set
#CONFIG_8139_NEW_RX_RESETis not set
#CONFIG_SIS900is not set
#CONFIG_EPIC100is not set
#CONFIG_SUNDANCEis not set
#CONFIG_TLANis not set
#CONFIG_VIA_RHINEis not set
#CONFIG_VIA_RHINE_MMIOis not set
#CONFIG_NET_POCKETis not set#
# Ethernet (1000 Mbit)
#
#CONFIG_ACENICis not set
#CONFIG_DL2Kis not set
#CONFIG_E1000is not set
#CONFIG_MYRI_SBUSis not set
#CONFIG_NS83820is not set
#CONFIG_HAMACHIis not set
#CONFIG_YELLOWFINis not set
#CONFIG_SK98LINis not set
#CONFIG_TIGON3is not set
#CONFIG_FDDIis not set
#CONFIG_HIPPIis not set
#CONFIG_PLIPis not set
#CONFIG_PPPis not set
#CONFIG_SLIPis not set#
# Wireless LAN (non-hamradio)
#
#CONFIG_NET_RADIOis not set#
# Token Ring devices
#
#CONFIG_TRis not set
#CONFIG_NET_FCis not set
#CONFIG_RCPCIis not set
#CONFIG_SHAPERis not set#
# Wan interfaces
#
#CONFIG_WANis not set#
# Tulip family network device support
#
#CONFIG_NET_TULIPis not set#
# Amateur Radio support
#
#CONFIG_HAMRADIOis not set#
# IrDA (infrared) support
#
#CONFIG_IRDAis not set#
# ISDN subsystem
#
#CONFIG_ISDN_BOOLis not set#
# Input device support
#CONFIG_INPUT=y#
# Userland interfaces
#CONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#CONFIG_INPUT_JOYDEVis not set
#CONFIG_INPUT_TSDEVis not setCONFIG_INPUT_EVDEV=y
#CONFIG_INPUT_EVBUGis not set#
# Input I/O drivers
#
#CONFIG_GAMEPORTis not setCONFIG_SOUND_GAMEPORT=y
#CONFIG_GAMEPORT_NS558is not set
#CONFIG_GAMEPORT_L4is not set
#CONFIG_GAMEPORT_EMU10K1is not set
#CONFIG_GAMEPORT_VORTEXis not set
#CONFIG_GAMEPORT_FM801is not set
#CONFIG_GAMEPORT_CS461Xis not setCONFIG_SERIO=y
#CONFIG_SERIO_I8042is not setCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12
#CONFIG_SERIO_SERPORTis not set
#CONFIG_SERIO_CT82C710is not set
#CONFIG_SERIO_PARKBDis not set#
# Input Device Drivers
#CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=y
#CONFIG_KEYBOARD_SUNKBDis not set
#CONFIG_KEYBOARD_PS2SERKBDis not set
#CONFIG_KEYBOARD_XTKBDis not set
#CONFIG_INPUT_MOUSEis not set
#CONFIG_MOUSE_PS2is not set
#CONFIG_MOUSE_SERIALis not set
#CONFIG_MOUSE_INPORTis not set
#CONFIG_MOUSE_LOGIBMis not set
#CONFIG_MOUSE_PC110PADis not set
#CONFIG_INPUT_JOYSTICKis not set
#CONFIG_JOYSTICK_ANALOGis not set
#CONFIG_JOYSTICK_A3Dis not set
#CONFIG_JOYSTICK_ADIis not set
#CONFIG_JOYSTICK_COBRAis not set
#CONFIG_JOYSTICK_GF2Kis not set
#CONFIG_JOYSTICK_GRIPis not set
#CONFIG_JOYSTICK_GUILLEMOTis not set
#CONFIG_JOYSTICK_INTERACTis not set
#CONFIG_JOYSTICK_SIDEWINDERis not set
#CONFIG_JOYSTICK_TMDCis not set
#CONFIG_JOYSTICK_IFORCE_USBis not set
#CONFIG_JOYSTICK_IFORCE_232is not set
#CONFIG_JOYSTICK_WARRIORis not set
#CONFIG_JOYSTICK_MAGELLANis not set
#CONFIG_JOYSTICK_SPACEORBis not set
#CONFIG_JOYSTICK_SPACEBALLis not set
#CONFIG_JOYSTICK_STINGERis not set
#CONFIG_JOYSTICK_TWIDDLERis not set
#CONFIG_JOYSTICK_DB9is not set
#CONFIG_JOYSTICK_GAMECONis not set
#CONFIG_JOYSTICK_TURBOGRAFXis not set
#CONFIG_INPUT_TOUCHSCREENis not set
#CONFIG_TOUCHSCREEN_GUNZEis not set#
# Character devices
#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_SERIAL=y
#CONFIG_SERIAL_CONSOLEis not set
#CONFIG_SERIAL_EXTENDEDis not set
#CONFIG_SERIAL_NONSTANDARDis not setCONFIG_UNIX98_PTYS=yCONFIG_UNIX98_PTY_COUNT=256#
# I2C support
#CONFIG_I2C=mCONFIG_I2C_ALGOBIT=m
#CONFIG_I2C_PHILIPSPARis not set
#CONFIG_I2C_ELVis not set
#CONFIG_I2C_VELLEMANis not set
#CONFIG_I2C_ALGOPCFis not setCONFIG_I2C_CHARDEV=mCONFIG_I2C_PROC=m
#CONFIG_QIC02_TAPEis not set#
# Watchdog Cards
#
#CONFIG_WATCHDOGis not set
#CONFIG_AMD_RNGis not setCONFIG_INTEL_RNG=y
#CONFIG_NVRAMis not setCONFIG_RTC=y
#CONFIG_DTLKis not set
#CONFIG_R3964is not set
#CONFIG_APPLICOMis not set
#CONFIG_SONYPIis not set#
# Ftape, the floppy tape device driver
#
#CONFIG_FTAPEis not setCONFIG_AGP=yCONFIG_AGP_INTEL=y
#CONFIG_AGP_I810is not set
#CONFIG_AGP_VIAis not set
#CONFIG_AGP_AMDis not set
#CONFIG_AGP_SISis not set
#CONFIG_AGP_ALIis not set
#CONFIG_AGP_SWORKSis not setCONFIG_DRM=y
#CONFIG_DRM_TDFXis not set
#CONFIG_DRM_GAMMAis not set
#CONFIG_DRM_R128is not set
#CONFIG_DRM_RADEONis not set
#CONFIG_DRM_I810is not set
#CONFIG_DRM_I830is not set
#CONFIG_DRM_MGAis not set
#CONFIG_DRM_SISis not set
#CONFIG_MWAVEis not set#
# Multimedia devices
#
#CONFIG_VIDEO_DEVis not set#
# File systems
#
#CONFIG_QUOTAis not set
#CONFIG_QFMT_V1is not set
#CONFIG_QFMT_V2is not set
#CONFIG_AUTOFS_FSis not setCONFIG_AUTOFS4_FS=y
#CONFIG_REISERFS_FSis not set
#CONFIG_REISERFS_CHECKis not set
#CONFIG_REISERFS_PROC_INFOis not set
#CONFIG_ADFS_FSis not set
#CONFIG_ADFS_FS_RWis not set
#CONFIG_AFFS_FSis not set
#CONFIG_HFS_FSis not set
#CONFIG_BFS_FSis not setCONFIG_EXT3_FS=yCONFIG_JBD=y
#CONFIG_JBD_DEBUGis not setCONFIG_FAT_FS=mCONFIG_MSDOS_FS=m
#CONFIG_UMSDOS_FSis not setCONFIG_VFAT_FS=m
#CONFIG_EFS_FSis not set
#CONFIG_JFFS_FSis not set
#CONFIG_JFFS2_FSis not set
#CONFIG_CRAMFSis not set
#CONFIG_TMPFSis not setCONFIG_RAMFS=yCONFIG_ISO9660_FS=mCONFIG_JOLIET=y
#CONFIG_ZISOFSis not set
#CONFIG_JFS_FSis not set
#CONFIG_JFS_DEBUGis not set
#CONFIG_JFS_STATISTICSis not set
#CONFIG_MINIX_FSis not set
#CONFIG_VXFS_FSis not set
#CONFIG_NTFS_FSis not set
#CONFIG_NTFS_DEBUGis not set
#CONFIG_HPFS_FSis not setCONFIG_PROC_FS=yCONFIG_DEVFS_FS=yCONFIG_DEVFS_MOUNT=y
#CONFIG_DEVFS_DEBUGis not set
#CONFIG_DEVPTS_FSis not set
#CONFIG_QNX4FS_FSis not set
#CONFIG_QNX4FS_RWis not set
#CONFIG_ROMFS_FSis not setCONFIG_EXT2_FS=m
#CONFIG_SYSV_FSis not set
#CONFIG_UDF_FSis not set
#CONFIG_UDF_RWis not set
#CONFIG_UFS_FSis not set
#CONFIG_UFS_FS_WRITEis not set#
# Network File Systems
#
#CONFIG_CODA_FSis not set
#CONFIG_INTERMEZZO_FSis not set
#CONFIG_NFS_FSis not set
#CONFIG_NFS_V3is not set
#CONFIG_ROOT_NFSis not set
#CONFIG_NFSDis not set
#CONFIG_NFSD_V3is not set
#CONFIG_NFSD_TCPis not set
#CONFIG_SUNRPCis not set
#CONFIG_LOCKDis not set
#CONFIG_EXPORTFSis not setCONFIG_SMB_FS=y
#CONFIG_SMB_NLS_DEFAULTis not set
#CONFIG_NCP_FSis not set
#CONFIG_NCPFS_PACKET_SIGNINGis not set
#CONFIG_NCPFS_IOCTL_LOCKINGis not set
#CONFIG_NCPFS_STRONGis not set
#CONFIG_NCPFS_NFS_NSis not set
#CONFIG_NCPFS_OS2_NSis not set
#CONFIG_NCPFS_SMALLDOSis not set
#CONFIG_NCPFS_NLSis not set
#CONFIG_NCPFS_EXTRASis not set
#CONFIG_ZISOFS_FSis not set#
# Partition Types
#
#CONFIG_PARTITION_ADVANCEDis not setCONFIG_MSDOS_PARTITION=yCONFIG_SMB_NLS=yCONFIG_NLS=y#
# Native Language Support
#CONFIG_NLS_DEFAULT="iso8859-1"CONFIG_NLS_CODEPAGE_437=y
#CONFIG_NLS_CODEPAGE_737is not set
#CONFIG_NLS_CODEPAGE_775is not set
#CONFIG_NLS_CODEPAGE_850is not set
#CONFIG_NLS_CODEPAGE_852is not set
#CONFIG_NLS_CODEPAGE_855is not set
#CONFIG_NLS_CODEPAGE_857is not set
#CONFIG_NLS_CODEPAGE_860is not set
#CONFIG_NLS_CODEPAGE_861is not set
#CONFIG_NLS_CODEPAGE_862is not set
#CONFIG_NLS_CODEPAGE_863is not set
#CONFIG_NLS_CODEPAGE_864is not set
#CONFIG_NLS_CODEPAGE_865is not set
#CONFIG_NLS_CODEPAGE_866is not set
#CONFIG_NLS_CODEPAGE_869is not set
#CONFIG_NLS_CODEPAGE_936is not set
#CONFIG_NLS_CODEPAGE_950is not set
#CONFIG_NLS_CODEPAGE_932is not set
#CONFIG_NLS_CODEPAGE_949is not set
#CONFIG_NLS_CODEPAGE_874is not set
#CONFIG_NLS_ISO8859_8is not set
#CONFIG_NLS_CODEPAGE_1250is not set
#CONFIG_NLS_CODEPAGE_1251is not setCONFIG_NLS_ISO8859_1=y
#CONFIG_NLS_ISO8859_2is not set
#CONFIG_NLS_ISO8859_3is not set
#CONFIG_NLS_ISO8859_4is not set
#CONFIG_NLS_ISO8859_5is not set
#CONFIG_NLS_ISO8859_6is not set
#CONFIG_NLS_ISO8859_7is not set
#CONFIG_NLS_ISO8859_9is not set
#CONFIG_NLS_ISO8859_13is not set
#CONFIG_NLS_ISO8859_14is not set
#CONFIG_NLS_ISO8859_15is not set
#CONFIG_NLS_KOI8_Ris not set
#CONFIG_NLS_KOI8_Uis not set
#CONFIG_NLS_UTF8is not set#
# Console drivers
#CONFIG_VGA_CONSOLE=yCONFIG_VIDEO_SELECT=y
#CONFIG_MDA_CONSOLEis not set#
# Frame-buffer support
#
#CONFIG_FBis not set#
# Sound
#CONFIG_SOUND=m#
# Open Sound System
#
#CONFIG_SOUND_PRIMEis not set#
# Advanced Linux Sound Architecture
#CONFIG_SND=m
#CONFIG_SND_SEQUENCERis not setCONFIG_SND_OSSEMUL=yCONFIG_SND_MIXER_OSS=mCONFIG_SND_PCM_OSS=m
#CONFIG_SND_SEQUENCER_OSSis not setCONFIG_SND_RTCTIMER=m
#CONFIG_SND_VERBOSE_PRINTKis not set
#CONFIG_SND_DEBUGis not set
#CONFIG_SND_DEBUG_MEMORYis not set
#CONFIG_SND_DEBUG_DETECTis not set#
# Generic devices
#
#CONFIG_SND_DUMMYis not set
#CONFIG_SND_VIRMIDIis not set
#CONFIG_SND_MTPAVis not set
#CONFIG_SND_SERIAL_U16550is not set
#CONFIG_SND_MPU401is not set#
# PCI devices
#
#CONFIG_SND_ALI5451is not set
#CONFIG_SND_CS46XXis not setCONFIG_SND_EMU10K1=m
#CONFIG_SND_KORG1212is not set
#CONFIG_SND_NM256is not set
#CONFIG_SND_RME32is not set
#CONFIG_SND_RME96is not set
#CONFIG_SND_RME9652is not set
#CONFIG_SND_HDSPis not set
#CONFIG_SND_TRIDENTis not set
#CONFIG_SND_YMFPCIis not set
#CONFIG_SND_ALS4000is not set
#CONFIG_SND_CMIPCIis not set
#CONFIG_SND_ENS1370is not set
#CONFIG_SND_ENS1371is not set
#CONFIG_SND_ES1938is not set
#CONFIG_SND_ES1968is not set
#CONFIG_SND_MAESTRO3is not set
#CONFIG_SND_FM801is not set
#CONFIG_SND_ICE1712is not set
#CONFIG_SND_INTEL8X0is not set
#CONFIG_SND_SONICVIBESis not set
#CONFIG_SND_VIA686is not set
#CONFIG_SND_VIA8233is not set#
# USB support
#CONFIG_USB=m
#CONFIG_USB_DEBUGis not set#
# Miscellaneous USB options
#CONFIG_USB_DEVICEFS=yCONFIG_USB_LONG_TIMEOUT=y
#CONFIG_USB_BANDWIDTHis not set
#CONFIG_USB_DYNAMIC_MINORSis not set#
# USB Host Controller Drivers
#
#CONFIG_USB_EHCI_HCDis not set
#CONFIG_USB_OHCI_HCDis not setCONFIG_USB_UHCI_HCD_ALT=m#
# USB Device Class drivers
#
#CONFIG_USB_AUDIOis not set
#CONFIG_USB_BLUETOOTH_TTYis not set
#CONFIG_USB_MIDIis not set
#CONFIG_USB_ACMis not set
#CONFIG_USB_PRINTERis not setCONFIG_USB_STORAGE=m
#CONFIG_USB_STORAGE_DEBUGis not set
#CONFIG_USB_STORAGE_DATAFABis not set
#CONFIG_USB_STORAGE_FREECOMis not set
#CONFIG_USB_STORAGE_ISD200is not set
#CONFIG_USB_STORAGE_DPCMis not set
#CONFIG_USB_STORAGE_HP8200eis not set
#CONFIG_USB_STORAGE_SDDR09is not set
#CONFIG_USB_STORAGE_SDDR55is not set
#CONFIG_USB_STORAGE_JUMPSHOTis not set#
# USB Human Interface Devices (HID)
#CONFIG_USB_HID=mCONFIG_USB_HIDINPUT=y
#CONFIG_USB_HIDDEVis not set
#CONFIG_USB_KBDis not set
#CONFIG_USB_MOUSEis not set
#CONFIG_USB_AIPTEKis not set
#CONFIG_USB_WACOMis not set#
# USB Imaging devices
#
#CONFIG_USB_MDC800is not set
#CONFIG_USB_SCANNERis not set
#CONFIG_USB_MICROTEKis not set
#CONFIG_USB_HPUSBSCSIis not set#
# USB Multimedia devices
#
#CONFIG_USB_DABUSBis not set#
# Video4Linux support is needed for USB Multimedia device support
#
#CONFIG_USB_VICAMis not set
#CONFIG_USB_DSBRis not set
#CONFIG_USB_IBMCAMis not set
#CONFIG_USB_KONICAWCis not set
#CONFIG_USB_OV511is not set
#CONFIG_USB_PWCis not set
#CONFIG_USB_SE401is not set
#CONFIG_USB_STV680is not set#
# USB Network adaptors
#
#CONFIG_USB_CATCis not set
#CONFIG_USB_CDCETHERis not set
#CONFIG_USB_KAWETHis not set
#CONFIG_USB_PEGASUSis not set
#CONFIG_USB_RTL8150is not set
#CONFIG_USB_USBNETis not set#
# USB port drivers
#
#CONFIG_USB_USS720is not set#
# USB Serial Converter support
#
#CONFIG_USB_SERIALis not set
#CONFIG_USB_SERIAL_GENERICis not set
#CONFIG_USB_SERIAL_BELKINis not set
#CONFIG_USB_SERIAL_WHITEHEATis not set
#CONFIG_USB_SERIAL_DIGI_ACCELEPORTis not set
#CONFIG_USB_SERIAL_EMPEGis not set
#CONFIG_USB_SERIAL_FTDI_SIOis not set
#CONFIG_USB_SERIAL_VISORis not set
#CONFIG_USB_SERIAL_IPAQis not set
#CONFIG_USB_SERIAL_IRis not set
#CONFIG_USB_SERIAL_EDGEPORTis not set
#CONFIG_USB_SERIAL_KEYSPAN_PDAis not set
#CONFIG_USB_SERIAL_KEYSPANis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28is not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28Xis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28XAis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28XBis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19is not set
#CONFIG_USB_SERIAL_KEYSPAN_USA18Xis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19Wis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19QWis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19QIis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA49Wis not set
#CONFIG_USB_SERIAL_KLSIis not set
#CONFIG_USB_SERIAL_MCT_U232is not set
#CONFIG_USB_SERIAL_PL2303is not set
#CONFIG_USB_SERIAL_SAFEis not set
#CONFIG_USB_SERIAL_SAFE_PADDEDis not set
#CONFIG_USB_SERIAL_CYBERJACKis not set
#CONFIG_USB_SERIAL_XIRCOMis not set
#CONFIG_USB_SERIAL_OMNINETis not set#
# USB Miscellaneous drivers
#
#CONFIG_USB_EMI26is not set
#CONFIG_USB_TIGLis not set
#CONFIG_USB_AUERSWALDis not set
#CONFIG_USB_RIO500is not set
#CONFIG_USB_BRLVGERis not set#
# Bluetooth support
#
#CONFIG_BLUEZis not set#
# Kernel hacking
#CONFIG_DEBUG_KERNEL=y
#CONFIG_DEBUG_OBSOLETEis not set
#CONFIG_DEBUG_SLABis not set
#CONFIG_DEBUG_IOVIRTis not setCONFIG_MAGIC_SYSRQ=y
#CONFIG_DEBUG_SPINLOCKis not set
#CONFIG_DEBUG_486_STRINGis not set
#CONFIG_FRAME_POINTERis not set#
# Library routines
#CONFIG_CRC32=y
#CONFIG_ZLIB_INFLATEis not set
#CONFIG_ZLIB_DEFLATEis not set
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 8 lines · Vojtech Pavlik
Hi!
Okay, I wrote all these input drivers. So I'd like to see them working. ;)
All you should need for proper function of both keyboard and mouse on a all-input-driver based system (like -dj kernels, or linux-input BK tree are) is:
Quoted 15 lines
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_SERIO=yCONFIG_SERIO_I8042=yCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=y
I just gave this a try with 2.5.25-dj2, and I still don't have a
working keyboard. Mouse works fine; no response from the keyboard. revelant parts of .config below:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not setCONFIG_GAMEPORT=mCONFIG_SOUND_GAMEPORT=mCONFIG_GAMEPORT_FM801=mCONFIG_SERIO=yCONFIG_SERIO_I8042=yCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12CONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=y
/proc/interrupts shows:
CPU0
0: 108187 XT-PIC timer 2: 0 XT-PIC cascade 4: 182 XT-PIC serial 5: 1 XT-PIC parport0 8: 1 XT-PIC rtc 10: 530 XT-PIC eth0 12: 830 XT-PIC i8042 14: 3754 XT-PIC ide0 15: 1 XT-PIC ide1 NMI: 0 LOC: 108090 ERR: 124 MIS: 0
From the above part of .config, IRQ1 should be set for the keyboard,
while IRQ 12 for the AUX port. 12 is set, 1 is not. dmesg shows:
Linux version 2.5.25-dj2 (root@bellicha) (gcc version 2.95.3 20010315 (release)) #1 Sat Jul 13 14:30:44 PDT 2002
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
user-defined physical RAM map:
user: 0000000000000000 - 000000000009fc00 (usable)
user: 000000000009fc00 - 00000000000a0000 (reserved)
user: 00000000000f0000 - 0000000000100000 (reserved)
user: 0000000000100000 - 000000001fff0000 (usable)
user: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
user: 000000001fff3000 - 0000000020000000 (ACPI data)
user: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=unix ro root=301 ether=0,0,0,eth0 ether=0,0,0,eth1 mem=512m devfs=mount video=aty128fb:mode:1280x1024,font:SUN12x22 Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1133.544 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2228.22 BogoMIPS
Memory: 516620k/524224k available (1183k kernel code, 7216k reserved, 345k data, 244k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000 CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000 CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1133.0220 MHz.
..... host bus clock speed is 266.0640 MHz.
cpu: 0, clocks: 266640, slice: 133320 CPU0<T0:266640,T1:133312,D:8,S:133320,C:266640>
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec: init pool 0, 1 entries, 12 bytes
biovec: init pool 1, 4 entries, 48 bytes
biovec: init pool 2, 16 entries, 192 bytes
biovec: init pool 3, 64 entries, 768 bytes
biovec: init pool 4, 128 entries, 1536 bytes
biovec: init pool 5, 256 entries, 3072 bytes
Journalled Block Device driver loaded
devfs: v1.17 (20020514) Richard Gooch ([email protected])
devfs: devfs_debug: 0x0
devfs: boot_options: 0x1
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
aty128fb: Rage128 BIOS located at segment C00C0000
aty128fb: Rage128 Pro TF (AGP) [chip rev 0x4] 32M 128-bit SDR SGRAM (1:1)
Console: switching to colour frame buffer device 80x30
fb0: ATY Rage128 frame buffer device on PCI
aty128fb: Rage128 MTRR set to ON
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.11
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
[drm] AGP 0.99 on VIA Apollo KT133 @ 0xd0000000 64MB
[drm] Initialized r128 2.2.0 20010917 on minor 0
[drm] AGP 0.99 on VIA Apollo KT133 @ 0xd0000000 64MB
[drm] Initialized radeon 1.3.1 20020611 on minor 1
block: 256 slots per queue, batch=32
ATA/ATAPI device driver v7.0.0
ATA: PCI bus speed 33.3MHz
ATA: VIA Technologies, Inc. Bus Master IDE, PCI slot 00:07.1
ATA: chipset rev.: 6
ATA: non-legacy mode: IRQ probe delayedVP_IDE: VIA vt82c686b (rev 40) ATA UDMA100 controller on PCI 00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:piohda: Maxtor 91531U3, DISK drive
hdb: WDC WD200AB-00BVA0, DISK drive
hdc: CD-W54E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 30015216 sectors w/512KiB Cache, CHS=29777/16/63, UDMA(66)
/dev/ide/host0/bus0/target0/lun0: [PTBL] [1868/255/63] p1 p2 p3 p4 < p5 p6 p7 p8 >
hdb: 39102336 sectors w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
/dev/ide/host0/bus0/target1/lun0: [PTBL] [2434/255/63] p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 >
mice: PS/2 mouse device common for all mice
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 244k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding 1028120k swap on /dev/hdb1. Priority:-1 extents:1
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,67), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,67)) for (ide0(3,67))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,71), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,71)) for (ide0(3,71))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,70), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,70)) for (ide0(3,70))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,7), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,7)) for (ide0(3,7))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,69), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,69)) for (ide0(3,69))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,5), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,5)) for (ide0(3,5))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,66), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,66)) for (ide0(3,66))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,6), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,6)) for (ide0(3,6))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,72), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,72)) for (ide0(3,72))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,73), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,73)) for (ide0(3,73))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,74), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,74)) for (ide0(3,74))
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device ide0(3,8), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (ide0(3,8)) for (ide0(3,8))
Using r5 hash to sort names
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.htmleepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
PCI: Found IRQ 10 for device 00:08.0
eth0: Intel Corp. 82557 [Ethernet Pro 100], 00:90:27:10:08:1C, IRQ 10.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 689661-004, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x24c9f043).
Receiver lock-up workaround activated.
parport0: PC-style at 0x278, irq 5 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).ip_tables: (C) 2000-2002 Netfilter core teamip_conntrack version 2.0 (4095 buckets, 32760 max) - 292 bytes per conntrack
ASSERT ip_conntrack_core.c:544 &ip_conntrack_lock not readlocked
Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 1
So I don't really know what is causing my keyboard (PS/2) to not work
with the new API. I also don't know how others are getting it to work.. any insight?
BL.
Signature · 4 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF
Quoted 16 lines · A Guy Called Tyketto
I just gave this a try with 2.5.25-dj2, and I still don't have a
working keyboard. Mouse works fine; no response from the keyboard. revelant parts of .config below:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=m
#CONFIG_INPUT_EVBUGis not setCONFIG_GAMEPORT=mCONFIG_SOUND_GAMEPORT=mCONFIG_GAMEPORT_FM801=mCONFIG_SERIO=yCONFIG_SERIO_I8042=y
Quoted 8 lines
CONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12CONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=y
The .config is OK.
Quoted 11 lines
/proc/interruptsshows:CPU0
0: 108187 XT-PIC timer 2: 0 XT-PIC cascade 4: 182 XT-PIC serial 5: 1 XT-PIC parport0 8: 1 XT-PIC rtc 10: 530 XT-PIC eth0 12: 830 XT-PIC i8042 14: 3754 XT-PIC ide0
Unfortunately this doesn't list interrupts, which happened, but are no longer claimed by any driver - and the i8042 driver frees the interrupt when it detects no device.
Quoted 7 lines
From the above part of .config, IRQ1 should be set for the keyboard,
while IRQ 12 for the AUX port. 12 is set, 1 is not. dmesg shows:mice: PS/2 mouse device common for all mice
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
So it detected both the KBD and AUX ports properly, but for some reason it couldn't identify the attached keyboard.
Can you #define ATKBD_DEBUG in drivers/input/keyboard/atkbd.c? Then you'll see what happened in' dmesg'.
Quoted 3 lines
So I don't really know what is causing my keyboard (PS/2) to not work
with the new API. I also don't know how others are getting it to work.. any insight?
Most likely you have a somewhat unusual keyboard - it may be responding too slow perhaps, so that the driver times out - or doesn't support some of the commands the driver expects to use.
Or the mouse kills the keyboard. This also can happen - they share common resources. This would need more debugging then.
So, what's the keyboard, what's the mouse, and what's the mainboard exactly?
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 4 lines · Vojtech Pavlik
Unfortunately this doesn't list interrupts, which happened, but are no longer claimed by any driver - and the i8042 driver frees the interrupt when it detects no device.
Interesting.. it detects it, as per dmesg below, but then it frees
it.. really interesting..
Quoted 8 lines
Quoted 7 lines
From the above part of .config, IRQ1 should be set for the keyboard,
while IRQ 12 for the AUX port. 12 is set, 1 is not. dmesg shows:mice: PS/2 mouse device common for all mice
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
Quoted 5 lines
So it detected both the KBD and AUX ports properly, but for some reason it couldn't identify the attached keyboard.
Can you #define
ATKBD_DEBUGindrivers/input/keyboard/atkbd.c? Then you'll see what happened in' dmesg'.
Just did. dmesg follows:
Linux version 2.5.25-dj2 (root@bellicha) (gcc version 2.95.3 20010315 (release)) #1 Sun Jul 14 01:50:09 PDT 2002
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
user-defined physical RAM map:
user: 0000000000000000 - 000000000009fc00 (usable)
user: 000000000009fc00 - 00000000000a0000 (reserved)
user: 00000000000f0000 - 0000000000100000 (reserved)
user: 0000000000100000 - 000000001fff0000 (usable)
user: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
user: 000000001fff3000 - 0000000020000000 (ACPI data)
user: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=unix ro root=301 ether=0,0,0,eth0 ether=0,0,0,eth1 mem=512m devfs=mount video=aty128fb:mode:1280x1024,font:SUN12x22 Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1133.510 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2228.22 BogoMIPS
Memory: 516620k/524224k available (1183k kernel code, 7216k reserved, 345k data, 244k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000 CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000 CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1133.0164 MHz.
..... host bus clock speed is 266.0626 MHz.
cpu: 0, clocks: 266626, slice: 133313 CPU0<T0:266624,T1:133296,D:15,S:133313,C:266626>
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
spurious 8259A interrupt: IRQ7.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec: init pool 0, 1 entries, 12 bytes
biovec: init pool 1, 4 entries, 48 bytes
biovec: init pool 2, 16 entries, 192 bytes
biovec: init pool 3, 64 entries, 768 bytes
biovec: init pool 4, 128 entries, 1536 bytes
biovec: init pool 5, 256 entries, 3072 bytes
Journalled Block Device driver loaded
devfs: v1.17 (20020514) Richard Gooch ([email protected])
devfs: devfs_debug: 0x0
devfs: boot_options: 0x1
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
aty128fb: Rage128 BIOS located at segment C00C0000
aty128fb: Rage128 Pro TF (AGP) [chip rev 0x4] 32M 128-bit SDR SGRAM (1:1)
Console: switching to colour frame buffer device 80x30
fb0: ATY Rage128 frame buffer device on PCI
aty128fb: Rage128 MTRR set to ON
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.11
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
[drm] AGP 0.99 on VIA Apollo KT133 @ 0xd0000000 64MB
[drm] Initialized r128 2.2.0 20010917 on minor 0
[drm] AGP 0.99 on VIA Apollo KT133 @ 0xd0000000 64MB
[drm] Initialized radeon 1.3.1 20020611 on minor 1
block: 256 slots per queue, batch=32
ATA/ATAPI device driver v7.0.0
ATA: PCI bus speed 33.3MHz
ATA: VIA Technologies, Inc. Bus Master IDE, PCI slot 00:07.1
ATA: chipset rev.: 6
ATA: non-legacy mode: IRQ probe delayedVP_IDE: VIA vt82c686b (rev 40) ATA UDMA100 controller on PCI 00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:piohda: Maxtor 91531U3, DISK drive
hdb: WDC WD200AB-00BVA0, DISK drive
hdc: CD-W54E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 30015216 sectors w/512KiB Cache, CHS=29777/16/63, UDMA(66) /dev/ide/host0/bus0/target0/lun0: [PTBL] [1868/255/63] p1 p2 p3 p4 < p5 p6 p7 p8 >
hdb: 39102336 sectors w/2048KiB Cache, CHS=38792/16/63, UDMA(100) /dev/ide/host0/bus0/target1/lun0: [PTBL] [2434/255/63] p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 >
mice: PS/2 mouse device common for all miceatkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
.
.
.
.
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.
htmleepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
PCI: Found IRQ 10 for device 00:08.0
eth0: Intel Corp. 82557 [Ethernet Pro 100], 00:90:27:10:08:1C, IRQ 10.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 689661-004, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x24c9f043).
Receiver lock-up workaround activated.
parport0: PC-style at 0x278, irq 5 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
Quoted 9 lines
Most likely you have a somewhat unusual keyboard - it may be responding too slow perhaps, so that the driver times out - or doesn't support some of the commands the driver expects to use.
Or the mouse kills the keyboard. This also can happen - they share common resources. This would need more debugging then.
So, what's the keyboard, what's the mouse, and what's the mainboard exactly?
I've tried this with 3 different keyboards, 3 different mice, and 3
combinations of each: wireless 104-key ps/2 keyboard. PS/2 cord from the box to the keyboard base, actual keyboard is wireless. bought it 4 years ago; 104-key keybord (w/power, sleep, and wake keys) bought 3 weeks ago, 104-key acer keyboard from a P100 from 7 years ago. all 3 mice are PS/2 mice; Acer mouse to go along with the Acer box and Acer keyboard, Microsoft PS/2 mouse, and MS Optical wheel mouse. The Acer and MS PS/2 mouse are straight PS/2. The optical is IMPS/2. motherboard is a Tyan S2390B, VIA82c686b chipset.
All 9 different combinations gave the same result. Mouse working,
keyboard not working.
BL.
Signature · 4 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF
Quoted 4 lines · A Guy Called Tyketto
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1
I've seen this when I was first looking into the input stuff recently. I think it was caused by the keyboard getting confused after I was testing the data and clock lines on the interface.
One fix I came up with (and discarded) was to try to reset the keyboard 3 times, and only fail if it failed all 3 times. The other fix (the one I ended up using) doesn't make sense to i8042 keyboard controllers.
Signature · 2 lines
Russell King ([email protected]) The developer of ARM Linux http://www.arm.linux.org.uk/personal/aboutme.html
Quoted 25 lines · A Guy Called Tyketto
Quoted 4 lines · Vojtech Pavlik
Unfortunately this doesn't list interrupts, which happened, but are no longer claimed by any driver - and the i8042 driver frees the interrupt when it detects no device.
Interesting.. it detects it, as per dmesg below, but then it frees
it.. really interesting..Quoted 8 lines
Quoted 7 lines
From the above part of .config, IRQ1 should be set for the keyboard,
while IRQ 12 for the AUX port. 12 is set, 1 is not. dmesg shows:mice: PS/2 mouse device common for all mice
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12Quoted 5 lines
So it detected both the KBD and AUX ports properly, but for some reason it couldn't identify the attached keyboard.
Can you #define
ATKBD_DEBUGindrivers/input/keyboard/atkbd.c? Then you'll see what happened in' dmesg'.Just did. dmesg follows:
Quoted 8 lines
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
NET4: Linux TCP/IP 1.0 for NET4.0
Ok. So this is the cause. The driver gets a '0xfe' response, which means "error, command not supported, or device not present'.
A keyboard must support the 0xf5 command ('reset').
So, the error response might be coming either from the mouse, or the controller, and somehow gets passed to the keyboard (they unfortunately share the same registers), or the response somes from the mouse driver first trying to probe for a mouse on the port.
So, please #define I8042_DEBUG_IO in drivers/input/serio/i8042.h as well, and try again. Then we'll know more.
Quoted 19 lines
Quoted 9 lines
Most likely you have a somewhat unusual keyboard - it may be responding too slow perhaps, so that the driver times out - or doesn't support some of the commands the driver expects to use.
Or the mouse kills the keyboard. This also can happen - they share common resources. This would need more debugging then.
So, what's the keyboard, what's the mouse, and what's the mainboard exactly?
I've tried this with 3 different keyboards, 3 different mice, and 3
combinations of each: wireless 104-key ps/2 keyboard. PS/2 cord from the box to the keyboard base, actual keyboard is wireless. bought it 4 years ago; 104-key keybord (w/power, sleep, and wake keys) bought 3 weeks ago, 104-key acer keyboard from a P100 from 7 years ago. all 3 mice are PS/2 mice; Acer mouse to go along with the Acer box and Acer keyboard, Microsoft PS/2 mouse, and MS Optical wheel mouse. The Acer and MS PS/2 mouse are straight PS/2. The optical is IMPS/2. motherboard is a Tyan S2390B, VIA82c686b chipset.
Quoted 2 lines
All 9 different combinations gave the same result. Mouse working,
keyboard not working.
Very intersting. It works for me on my via82c686b.
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 9 lines · Vojtech Pavlik
Quoted 4 lines
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1Ok. So this is the cause. The driver gets a '
0xfe' response, which means "error, command not supported, or device not present'.A keyboard must support the
0xf5command ('reset').
I have not followed the discussion and probably say something entirely out of context. But from the good old days I seem to recall commands 0xff "reset", 0xf5 "set defaults and deactivate" and reply 0xfe "please resend".
In principle nothing is wrong when one gets a 0xfe. The request is just: please say that again.
Andries
Quoted 12 lines · Andries Brouwer
Quoted 9 lines · Vojtech Pavlik
Quoted 4 lines
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1Ok. So this is the cause. The driver gets a '
0xfe' response, which means "error, command not supported, or device not present'.A keyboard must support the
0xf5command ('reset').
Quoted 7 lines
I have not followed the discussion and probably say something entirely out of context. But from the good old days I seem to recall commands
0xff"reset",0xf5"set defaults and deactivate" and reply0xfe"please resend".In principle nothing is wrong when one gets a
0xfe. The request is just: please say that again.
Commands:
0xf5 - n/a - Keyboard
Reset and disable keyboard. The keyboard performs a reset to a power
on state (without affecting the LEDs) and stops generating events.
0xff - 1*R - Keyboard / Mouse
Reset and perform the Basic Assurance Test (BAT). Device returns a
BAT completion code 0xaa. If it's a keyboard, then switches to scancode set 2. If it's a mouse, it also sends 0x00, 0x03 or 0x04 after 0xaa. Since BAT is also triggered on power-on, a device will send 0xaa immediately after being plugged in.
Responses:
0xfe
Resend. Keyboard will send this if it didn't receive the last command
correctly.
Unfortunately, 0xfe also happens when you send a command to a keyboard that's not plugged, or when the keyboard doesn't understand the command. Resending in those cases (which are the most common) would cause an infinite loop ...
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 4 lines · Vojtech Pavlik
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1
[...]
Quoted 10 lines
Responses:
0xfe
Resend. Keyboard will send this if it didn't receive the last command
correctly.Unfortunately,
0xfealso happens when you send a command to a keyboard that's not plugged, or when the keyboard doesn't understand the command. Resending in those cases (which are the most common) would cause an infinite loop ...
Not if implemented correctly.
Set the retry counter to 5 at the beginning.
if you get 0xfe: decrement retry counter,
if 0 :
no keyboard connected. Give up.
else
Just immediately resend the last command
else
set the retry counter to 5 again. process returned code
Roger.
Signature · 4 lines
** [email protected] ** http://www.BitWizard.nl/ ** +31-15-2137555 ** *-- BitWizard writes Linux device drivers for any device you may have! --* * There are old pilots, and there are bold pilots. * There are also old, bald pilots.
Quoted 21 lines · Rogier Wolff
Quoted 4 lines · Vojtech Pavlik
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1[...]
Quoted 10 lines
Responses:
0xfe
Resend. Keyboard will send this if it didn't receive the last command
correctly.Unfortunately,
0xfealso happens when you send a command to a keyboard that's not plugged, or when the keyboard doesn't understand the command. Resending in those cases (which are the most common) would cause an infinite loop ...Not if implemented correctly.
Set the retry counter to 5 at the beginning.
Quoted 8 lines
if you get
0xfe: decrement retry counter,
if 0 :
no keyboard connected. Give up.
else
Just immediately resend the last command
else
set the retry counter to 5 again. process returned code
Yes. Sure. I knew someone will suggest that. :) The only problem is, I've never seen a keyboard sending 0xfe because it wants the command sent again. Under normal circumstances, there aren't bit errors on the cable.
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 4 lines · Vojtech Pavlik
Yes. Sure. I knew someone will suggest that. :) The only problem is, I've never seen a keyboard sending
0xfebecause it wants the command sent again. Under normal circumstances, there aren't bit errors on the cable.
I think you missed my mail at the beginning of this thread.
Signature · 2 lines
Russell King ([email protected]) The developer of ARM Linux http://www.arm.linux.org.uk/personal/aboutme.html
Quoted 7 lines · Russell King
Quoted 4 lines · Vojtech Pavlik
Yes. Sure. I knew someone will suggest that. :) The only problem is, I've never seen a keyboard sending
0xfebecause it wants the command sent again. Under normal circumstances, there aren't bit errors on the cable.I think you missed my mail at the beginning of this thread.
I read it. Well, let's first see where the 0xfe really comes from. :)
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 10 lines · Vojtech Pavlik
Quoted 7 lines · Russell King
Quoted 4 lines · Vojtech Pavlik
Yes. Sure. I knew someone will suggest that. :) The only problem is, I've never seen a keyboard sending
0xfebecause it wants the command sent again. Under normal circumstances, there aren't bit errors on the cable.I think you missed my mail at the beginning of this thread.
I read it. Well, let's first see where the
0xfereally comes from. :)
Err, the keyboard. The hardware I saw it on was with just a plain PS/2 port with zero inteligence within; it's effectively a serial port talking direct to the keyboard.
Signature · 2 lines
Russell King ([email protected]) The developer of ARM Linux http://www.arm.linux.org.uk/personal/aboutme.html
Quoted 8 lines · Russell King
Quoted 7 lines · Vojtech Pavlik
Quoted 6 lines · Russell King
Quoted 4 lines · Vojtech Pavlik
Yes. Sure. I knew someone will suggest that. :) The only problem is, I've never seen a keyboard sending
0xfebecause it wants the command sent again. Under normal circumstances, there aren't bit errors on the cable.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
I think you missed my mail at the beginning of this thread.
I read it. Well, let's first see where the
0xfereally comes from. :)Err, the keyboard. The hardware I saw it on was with just a plain PS/2 port with zero inteligence within; it's effectively a serial port talking direct to the keyboard.
I was talking about the one from Tyketto, yours was most likely happening because the keyboard considered the line testing as a beginning of a character being sent, then attached the rest of the initial 0xf5 to it and got a nonsense. This is not exactly a bit error on the wire.
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 9 lines · Vojtech Pavlik
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
atkbd.c: Sent: f5atkbd.c: Received feOk. So this is the cause. The driver gets a '
0xfe' response, which means "error, command not supported, or device not present'.In principle nothing is wrong when one gets a
0xfe. The request is just: please say that again.
Quoted 8 lines
0xfe
Resend. Keyboard will send this if it didn't receive the last command
correctly.Unfortunately,
0xfealso happens when you send a command to a keyboard that's not plugged, or when the keyboard doesn't understand the command. Resending in those cases (which are the most common) would cause an infinite loop ...
Not so pessimistic. The first resend may be needed because the keyboard does not stabilize so quickly after power on.
You wait 25 ms and try again. Wait 500 ms and try again. Give up.
But if this is really the first command sent to the keyboard, then I think 0xf5 is uncommon.
One usually sees a sequence like:
Send 0xaa to port 64. Wait for the 0x55 ack.
Do things to enable A20, IRQ1, set scancode translation.
Send 0xff to port 60. Wait for the 0xfa ack. Wait for the 0xaa good status.
When 0xf5 fails, one might consider trying a more standard sequence.
Andries
Quoted 24 lines · Andries Brouwer
Quoted 9 lines · Vojtech Pavlik
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
atkbd.c: Sent: f5atkbd.c: Received feOk. So this is the cause. The driver gets a '
0xfe' response, which means "error, command not supported, or device not present'.In principle nothing is wrong when one gets a
0xfe. The request is just: please say that again.Quoted 8 lines
0xfe
Resend. Keyboard will send this if it didn't receive the last command
correctly.Unfortunately,
0xfealso happens when you send a command to a keyboard that's not plugged, or when the keyboard doesn't understand the command. Resending in those cases (which are the most common) would cause an infinite loop ...Not so pessimistic. The first resend may be needed because the keyboard does not stabilize so quickly after power on.
You wait 25 ms and try again. Wait 500 ms and try again. Give up.
Quoted 7 lines
But if this is really the first command sent to the keyboard, then I think
0xf5is uncommon.One usually sees a sequence like:
Send0xaato port 64. Wait for the0x55ack.
Do things to enable A20, IRQ1, set scancode translation.
Send0xffto port 60. Wait for the0xfaack. Wait for the0xaagood status.
The problem is that 0xff takes too long to finish to be done while Linux is booting, and it has already been done by the BIOS.
Quoted 1 line
When
0xf5fails, one might consider trying a more standard sequence.
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 5 lines · Vojtech Pavlik
Quoted 1 line · Andries Brouwer
Send
0xffto port 60. Wait for the0xfaack. Wait for the0xaagood status.The problem is that
0xfftakes too long to finish to be done while Linux is booting, and it has already been done by the BIOS.
Ah hem, "bios". Do we trust that hunk of proprietary code now? Note also that pc_keyb.c allowed for embedded devices where there is no BIOS. That said, not sending 0xff seems to be fine on the keyboards I have here. I wouldn't like to guarantee that it's fine across all keyboards though, just like sending 0xAA on reconnect isn't guaranteed.
Signature · 2 lines
Russell King ([email protected]) The developer of ARM Linux http://www.arm.linux.org.uk/personal/aboutme.html
Quoted 4 lines · Russell King
Quoted 3 lines · Vojtech Pavlik
Quoted 1 line · Andries Brouwer
Send
0xffto port 60. Wait for the0xfaack. Wait for the0xaagood status.
Quoted 8 lines
Quoted 2 lines
The problem is that
0xfftakes too long to finish to be done while Linux is booting, and it has already been done by the BIOS.Ah hem, "bios". Do we trust that hunk of proprietary code now? Note also that
pc_keyb.callowed for embedded devices where there is no BIOS. That said, not sending0xffseems to be fine on the keyboards I have here. I wouldn't like to guarantee that it's fine across all keyboards though, just like sending0xAAon reconnect isn't guaranteed.
Well, so far I've tested with about 20 different weird keyboards ... let's see. If the future shows we need 0xff, there's no problem adding it.
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 2 lines · Vojtech Pavlik
The problem is that
0xfftakes too long to finish to be done while Linux is booting, and it has already been done by the BIOS.
Certainly, you don't have to poll, do you? Just send the command and let
the kernel proceed. Resume initialization in the IRQ handler, when a response arrives (or never).
Signature · 3 lines
+ Maciej W. Rozycki, Technical University of Gdansk, Poland + +--------------------------------------------------------------+ + e-mail: [email protected], PGP key available +
Quoted 17 lines · Vojtech Pavlik
Quoted 11 lines
Just did. dmesg follows:
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
NET4: Linux TCP/IP 1.0 for NET4.0Ok. So this is the cause. The driver gets a '
0xfe' response, which means "error, command not supported, or device not present'.A keyboard must support the
0xf5command ('reset').
Quoted 8 lines
So, the error response might be coming either from the mouse, or the controller, and somehow gets passed to the keyboard (they unfortunately share the same registers), or the response somes from the mouse driver first trying to probe for a mouse on the port.
So, please #define
I8042_DEBUG_IOindrivers/input/serio/i8042.has well, and try again. Then we'll know more.
Just gave that a go.. no change in the dmesg output. Nothing written
out to stdout or anything via syslogd/klogd. See above for that output.
BL.
Signature · 4 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF
Quoted 23 lines · A Guy Called Tyketto
Quoted 22 lines · Vojtech Pavlik
Quoted 11 lines
Just did. dmesg follows:
mice: PS/2 mouse device common for all mice
atkbd.c: Sent: f5atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
NET4: Linux TCP/IP 1.0 for NET4.0Ok. So this is the cause. The driver gets a '
0xfe' response, which means "error, command not supported, or device not present'.A keyboard must support the
0xf5command ('reset').So, the error response might be coming either from the mouse, or the controller, and somehow gets passed to the keyboard (they unfortunately share the same registers), or the response somes from the mouse driver first trying to probe for a mouse on the port.
Quoted 6 lines
Quoted 3 lines
So, please #define
I8042_DEBUG_IOindrivers/input/serio/i8042.has well, and try again. Then we'll know more.Just gave that a go.. no change in the dmesg output. Nothing written
out to stdout or anything via syslogd/klogd. See above for that output.
Are you sure you didn't leave the #undef in that file?
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 7 lines · Vojtech Pavlik
Quoted 7 lines
Quoted 7 lines
A keyboard must support the
0xf5command ('reset').So, the error response might be coming either from the mouse, or the controller, and somehow gets passed to the keyboard (they unfortunately share the same registers), or the response somes from the mouse driver first trying to probe for a mouse on the port.
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
So, please #define
I8042_DEBUG_IOindrivers/input/serio/i8042.has well, and try again. Then we'll know more.Just gave that a go.. no change in the dmesg output. Nothing written
out to stdout or anything via syslogd/klogd. See above for that output.Are you sure you didn't leave the #undef in that file?
Sorry about that.. I defined before the #undef. made the change and
recompiled. dmesg is below:
block: 256 slots per queue, batch=32
ATA/ATAPI device driver v7.0.0
ATA: PCI bus speed 33.3MHz
ATA: VIA Technologies, Inc. Bus Master IDE, PCI slot 00:07.1
ATA: chipset rev.: 6
ATA: non-legacy mode: IRQ probe delayedVP_IDE: VIA vt82c686b (rev 40) ATA UDMA100 controller on PCI 00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:piohda: Maxtor 91531U3, DISK drive
hdb: WDC WD200AB-00BVA0, DISK drive
hdc: CD-W54E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 30015216 sectors w/512KiB Cache, CHS=29777/16/63, UDMA(66) /dev/ide/host0/bus0/target0/lun0: [PTBL] [1868/255/63] p1 p2 p3 p4 < p5 p6 p7 p8 >
hdb: 39102336 sectors w/2048KiB Cache, CHS=38792/16/63, UDMA(100) /dev/ide/host0/bus0/target1/lun0: [PTBL] [2434/255/63] p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 >
mice: PS/2 mouse device common for all micei8042.c: 20 -> i8042 (command) [0]i8042.c: 47 <- i8042 (return) [0]i8042.c: 60 -> i8042 (command) [0]i8042.c: 56 -> i8042 (parameter) [0]i8042.c: 60 -> i8042 (command) [0]i8042.c: 47 -> i8042 (parameter) [0]i8042.c: f6 -> i8042 (kbd-data) [0]i8042.c: fa <- i8042 (interrupt-kbd) [3]i8042.c: f2 -> i8042 (kbd-data) [3]i8042.c: fa <- i8042 (interrupt-kbd) [6]i8042.c: ab <- i8042 (interrupt-kbd) [7]i8042.c: 60 -> i8042 (command) [7]i8042.c: 56 -> i8042 (parameter) [7]i8042.c: 60 -> i8042 (command) [7]i8042.c: 47 -> i8042 (parameter) [7]atkbd.c: Sent: f5i8042.c: f5 -> i8042 (kbd-data) [7]i8042.c: 60 -> i8042 (command) [17]i8042.c: 56 -> i8042 (parameter) [17]i8042.c: fe <- i8042 (interrupt-kbd) [18]atkbd.c: Received fe
serio: i8042 KBD port at 0x60,0x64 irq 1i8042.c: d3 -> i8042 (command) [20]i8042.c: 5a -> i8042 (parameter) [20]i8042.c: a5 <- i8042 (return) [20]i8042.c: a9 -> i8042 (command) [20]i8042.c: 00 <- i8042 (return) [20]i8042.c: a7 -> i8042 (command) [20]i8042.c: 20 -> i8042 (command) [20]i8042.c: 76 <- i8042 (return) [20]i8042.c: a9 -> i8042 (command) [20]i8042.c: 00 <- i8042 (return) [20]i8042.c: a8 -> i8042 (command) [20]i8042.c: 20 -> i8042 (command) [20]i8042.c: 56 <- i8042 (return) [20]i8042.c: 60 -> i8042 (command) [20]i8042.c: 74 -> i8042 (parameter) [20]i8042.c: 60 -> i8042 (command) [20]i8042.c: 56 -> i8042 (parameter) [20]i8042.c: d4 -> i8042 (command) [20]i8042.c: f6 -> i8042 (parameter) [20]i8042.c: 60 -> i8042 (command) [20]i8042.c: 56 -> i8042 (parameter) [20]i8042.c: fa <- i8042 (interrupt-aux) [21]i8042.c: d4 -> i8042 (command) [21]i8042.c: f2 -> i8042 (parameter) [21]i8042.c: 60 -> i8042 (command) [21]i8042.c: 56 -> i8042 (parameter) [21]i8042.c: fa <- i8042 (interrupt-aux) [22]i8042.c: 00 <- i8042 (interrupt-aux) [23]i8042.c: d4 -> i8042 (command) [23]i8042.c: e8 -> i8042 (parameter) [23]i8042.c: 60 -> i8042 (command) [23]i8042.c: 56 -> i8042 (parameter) [23]i8042.c: fa <- i8042 (interrupt-aux) [24]i8042.c: d4 -> i8042 (command) [24]i8042.c: 03 -> i8042 (parameter) [24]i8042.c: 60 -> i8042 (command) [24]i8042.c: 56 -> i8042 (parameter) [24]i8042.c: fa <- i8042 (interrupt-aux) [25]i8042.c: d4 -> i8042 (command) [26]i8042.c: e6 -> i8042 (parameter) [26]i8042.c: 60 -> i8042 (command) [26]i8042.c: 56 -> i8042 (parameter) [26]i8042.c: fa <- i8042 (interrupt-aux) [27]i8042.c: d4 -> i8042 (command) [27]i8042.c: e6 -> i8042 (parameter) [27]i8042.c: 60 -> i8042 (command) [27]i8042.c: 56 -> i8042 (parameter) [27]i8042.c: fa <- i8042 (interrupt-aux) [28]i8042.c: d4 -> i8042 (command) [28]i8042.c: e6 -> i8042 (parameter) [28]i8042.c: 60 -> i8042 (command) [28]i8042.c: 56 -> i8042 (parameter) [28]i8042.c: fa <- i8042 (interrupt-aux) [29]i8042.c: d4 -> i8042 (command) [29]i8042.c: e9 -> i8042 (parameter) [29]i8042.c: 60 -> i8042 (command) [29]i8042.c: 56 -> i8042 (parameter) [29]i8042.c: fa <- i8042 (interrupt-aux) [30]i8042.c: 00 <- i8042 (interrupt-aux) [31]i8042.c: 03 <- i8042 (interrupt-aux) [32]i8042.c: 64 <- i8042 (interrupt-aux) [33]i8042.c: d4 -> i8042 (command) [33]i8042.c: e8 -> i8042 (parameter) [33]i8042.c: 60 -> i8042 (command) [33]i8042.c: 56 -> i8042 (parameter) [33]i8042.c: fa <- i8042 (interrupt-aux) [34]i8042.c: d4 -> i8042 (command) [34]i8042.c: 00 -> i8042 (parameter) [34]i8042.c: 60 -> i8042 (command) [34]i8042.c: 56 -> i8042 (parameter) [34]i8042.c: fa <- i8042 (interrupt-aux) [35]i8042.c: d4 -> i8042 (command) [35]i8042.c: e6 -> i8042 (parameter) [35]i8042.c: 60 -> i8042 (command) [35]i8042.c: 56 -> i8042 (parameter) [35]i8042.c: fa <- i8042 (interrupt-aux) [36]i8042.c: d4 -> i8042 (command) [36]i8042.c: e6 -> i8042 (parameter) [36]i8042.c: 60 -> i8042 (command) [36]i8042.c: 56 -> i8042 (parameter) [36]i8042.c: fa <- i8042 (interrupt-aux) [37]i8042.c: d4 -> i8042 (command) [37]i8042.c: e6 -> i8042 (parameter) [37]i8042.c: 60 -> i8042 (command) [37]i8042.c: 56 -> i8042 (parameter) [37]i8042.c: fa <- i8042 (interrupt-aux) [38]i8042.c: d4 -> i8042 (command) [38]i8042.c: e9 -> i8042 (parameter) [38]i8042.c: 60 -> i8042 (command) [38]i8042.c: 56 -> i8042 (parameter) [38]i8042.c: fa <- i8042 (interrupt-aux) [39]i8042.c: 00 <- i8042 (interrupt-aux) [40]i8042.c: 00 <- i8042 (interrupt-aux) [41]i8042.c: 64 <- i8042 (interrupt-aux) [42]i8042.c: d4 -> i8042 (command) [42]i8042.c: f3 -> i8042 (parameter) [42]i8042.c: 60 -> i8042 (command) [42]i8042.c: 56 -> i8042 (parameter) [42]i8042.c: fa <- i8042 (interrupt-aux) [43]i8042.c: d4 -> i8042 (command) [43]i8042.c: c8 -> i8042 (parameter) [43]i8042.c: 60 -> i8042 (command) [43]i8042.c: 56 -> i8042 (parameter) [43]i8042.c: fa <- i8042 (interrupt-aux) [44]i8042.c: d4 -> i8042 (command) [44]i8042.c: f3 -> i8042 (parameter) [44]i8042.c: 60 -> i8042 (command) [44]i8042.c: 56 -> i8042 (parameter) [44]i8042.c: fa <- i8042 (interrupt-aux) [45]i8042.c: d4 -> i8042 (command) [45]i8042.c: 64 -> i8042 (parameter) [45]i8042.c: 60 -> i8042 (command) [45]i8042.c: 56 -> i8042 (parameter) [45]i8042.c: fa <- i8042 (interrupt-aux) [46]i8042.c: d4 -> i8042 (command) [46]i8042.c: f3 -> i8042 (parameter) [46]i8042.c: 60 -> i8042 (command) [46]i8042.c: 56 -> i8042 (parameter) [46]i8042.c: fa <- i8042 (interrupt-aux) [47]i8042.c: d4 -> i8042 (command) [47]i8042.c: 50 -> i8042 (parameter) [47]i8042.c: 60 -> i8042 (command) [47]i8042.c: 56 -> i8042 (parameter) [47]i8042.c: fa <- i8042 (interrupt-aux) [48]i8042.c: d4 -> i8042 (command) [48]i8042.c: f2 -> i8042 (parameter) [48]i8042.c: 60 -> i8042 (command) [48]i8042.c: 56 -> i8042 (parameter) [48]i8042.c: fa <- i8042 (interrupt-aux) [49]i8042.c: 03 <- i8042 (interrupt-aux) [50]i8042.c: d4 -> i8042 (command) [50]i8042.c: f3 -> i8042 (parameter) [50]i8042.c: 60 -> i8042 (command) [50]i8042.c: 56 -> i8042 (parameter) [50]i8042.c: fa <- i8042 (interrupt-aux) [51]i8042.c: d4 -> i8042 (command) [51]i8042.c: c8 -> i8042 (parameter) [51]i8042.c: 60 -> i8042 (command) [51]i8042.c: 56 -> i8042 (parameter) [51]i8042.c: fa <- i8042 (interrupt-aux) [52]i8042.c: d4 -> i8042 (command) [52]i8042.c: f3 -> i8042 (parameter) [52]i8042.c: 60 -> i8042 (command) [52]i8042.c: 56 -> i8042 (parameter) [52]i8042.c: fa <- i8042 (interrupt-aux) [53]i8042.c: d4 -> i8042 (command) [53]i8042.c: c8 -> i8042 (parameter) [53]i8042.c: 60 -> i8042 (command) [53]i8042.c: 56 -> i8042 (parameter) [53]i8042.c: fa <- i8042 (interrupt-aux) [54]i8042.c: d4 -> i8042 (command) [54]i8042.c: f3 -> i8042 (parameter) [54]i8042.c: 60 -> i8042 (command) [54]i8042.c: 56 -> i8042 (parameter) [54]i8042.c: fa <- i8042 (interrupt-aux) [55]i8042.c: d4 -> i8042 (command) [55]i8042.c: 50 -> i8042 (parameter) [55]i8042.c: 60 -> i8042 (command) [55]i8042.c: 56 -> i8042 (parameter) [55]i8042.c: fa <- i8042 (interrupt-aux) [56]i8042.c: d4 -> i8042 (command) [56]i8042.c: f2 -> i8042 (parameter) [56]i8042.c: 60 -> i8042 (command) [56]i8042.c: 56 -> i8042 (parameter) [56]i8042.c: fa <- i8042 (interrupt-aux) [57]i8042.c: 03 <- i8042 (interrupt-aux) [58]
input: ImPS/2 Microsoft IntelliMouse on isa0060/serio1i8042.c: d4 -> i8042 (command) [60]i8042.c: f3 -> i8042 (parameter) [60]i8042.c: 60 -> i8042 (command) [60]i8042.c: 56 -> i8042 (parameter) [60]i8042.c: fa <- i8042 (interrupt-aux) [61]i8042.c: d4 -> i8042 (command) [61]i8042.c: 64 -> i8042 (parameter) [61]i8042.c: 60 -> i8042 (command) [61]i8042.c: 56 -> i8042 (parameter) [61]i8042.c: fa <- i8042 (interrupt-aux) [62]i8042.c: d4 -> i8042 (command) [62]i8042.c: f3 -> i8042 (parameter) [62]i8042.c: 60 -> i8042 (command) [62]i8042.c: 56 -> i8042 (parameter) [62]i8042.c: fa <- i8042 (interrupt-aux) [63]i8042.c: d4 -> i8042 (command) [63]i8042.c: c8 -> i8042 (parameter) [63]i8042.c: 60 -> i8042 (command) [63]i8042.c: 56 -> i8042 (parameter) [63]i8042.c: fa <- i8042 (interrupt-aux) [64]i8042.c: d4 -> i8042 (command) [64]i8042.c: e8 -> i8042 (parameter) [64]i8042.c: 60 -> i8042 (command) [64]i8042.c: 56 -> i8042 (parameter) [64]i8042.c: fa <- i8042 (interrupt-aux) [65]i8042.c: d4 -> i8042 (command) [65]i8042.c: 03 -> i8042 (parameter) [65]i8042.c: 60 -> i8042 (command) [65]i8042.c: 56 -> i8042 (parameter) [65]i8042.c: fa <- i8042 (interrupt-aux) [66]i8042.c: d4 -> i8042 (command) [67]i8042.c: e6 -> i8042 (parameter) [67]i8042.c: 60 -> i8042 (command) [67]i8042.c: 56 -> i8042 (parameter) [67]i8042.c: fa <- i8042 (interrupt-aux) [68]i8042.c: d4 -> i8042 (command) [68]i8042.c: ea -> i8042 (parameter) [68]i8042.c: 60 -> i8042 (command) [68]i8042.c: 56 -> i8042 (parameter) [68]i8042.c: fa <- i8042 (interrupt-aux) [69]i8042.c: d4 -> i8042 (command) [69]i8042.c: f4 -> i8042 (parameter) [69]i8042.c: 60 -> i8042 (command) [69]i8042.c: 56 -> i8042 (parameter) [69]i8042.c: fa <- i8042 (interrupt-aux) [70]
serio: i8042 AUX port at 0x60,0x64 irq 12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 244k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
There ya go.
BL.
Signature · 4 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF
I mentioned this before, but I had major pains with the new input drivers for keyboards not working with the Comapq Armada M700's, and gave that up. Now I got a new Compaq N800c, which forced me onto 2.5.x because of some of the hardware (Intel ICH3 et al).
I also had problems with input compiled in statically, and decided to go play with modules and a network cables and test and fix remotely. The end result is that with running RH7.3 and using modules I get keyboard and mouse to work.
Below is the relevant bit of the .config file and here the mkinitrd command-line used:
mkinitrd --preload input --preload evdev --preload keybdev --preload \
mousedev --preload serio --preload i8042 --preload atkbd --preload \
psmouse /boot/initrd-2.5.25-dj2-udiv-ide97.img 2.5.25-dj2-udiv-ide97
I used 2.5.25-dj2, and the posted fix on the list for the udiv compile problem and IDE97.
I might be a bit tired, but there seem to be no proper dependency between the modules, so that doing a modprobe atkbd doesnt get the other modules, this the --preloads.
I only have two problems left is that I have a laptop with both a stick and a glidepad, and the psmouse driver only enables the pad, and not the stick. The other is that the rpm command segfaults for no apparent reason under 2.5.x (tried .23, 24., and .25 and -dj varieties of them). Same also happens with vim, second time it edits a file.
mvh,
A
PS: Sitting with two laptops on a flight and a cross-over cable tends to worry the stewardesses on board a lot :)
# Input device support
#CONFIG_INPUT=mCONFIG_INPUT_KEYBDEV=mCONFIG_INPUT_MOUSEDEV=mCONFIG_INPUT_MOUSEDEV_SCREEN_X=1400CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1050CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_TSDEV is not setCONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set
# CONFIG_GAMEPORT is not setCONFIG_SOUND_GAMEPORT=y
# CONFIG_GAMEPORT_NS558 is not set
# CONFIG_GAMEPORT_L4 is not set
# CONFIG_GAMEPORT_EMU10K1 is not set
# CONFIG_GAMEPORT_VORTEX is not set
# CONFIG_GAMEPORT_FM801 is not set
# CONFIG_GAMEPORT_CS461X is not setCONFIG_SERIO=mCONFIG_SERIO_I8042=mCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12CONFIG_SERIO_SERPORT=m
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not setCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=m
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_PS2SERKBD is not set
# CONFIG_KEYBOARD_XTKBD is not setCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=mCONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_JOYSTICK_ANALOG is not set
# CONFIG_JOYSTICK_A3D is not set
# CONFIG_JOYSTICK_ADI is not set
# CONFIG_JOYSTICK_COBRA is not set
# CONFIG_JOYSTICK_GF2K is not set
# CONFIG_JOYSTICK_GRIP is not set
# CONFIG_JOYSTICK_GUILLEMOT is not set
# CONFIG_JOYSTICK_INTERACT is not set
# CONFIG_JOYSTICK_SIDEWINDER is not set
# CONFIG_JOYSTICK_TMDC is not set
# CONFIG_JOYSTICK_IFORCE_USB is not set
# CONFIG_JOYSTICK_IFORCE_232 is not set
# CONFIG_JOYSTICK_WARRIOR is not set
# CONFIG_JOYSTICK_MAGELLAN is not set
# CONFIG_JOYSTICK_SPACEORB is not set
# CONFIG_JOYSTICK_SPACEBALL is not set
# CONFIG_JOYSTICK_STINGER is not set
# CONFIG_JOYSTICK_TWIDDLER is not set
# CONFIG_JOYSTICK_DB9 is not set
# CONFIG_JOYSTICK_GAMECON is not set
# CONFIG_JOYSTICK_TURBOGRAFX is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
Quoted 1,131 lines · Vojtech Pavlik
Hi!
Okay, I wrote all these input drivers. So I'd like to see them working. ;)
All you should need for proper function of both keyboard and mouse on a all-input-driver based system (like -dj kernels, or linux-input BK tree are) is:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_SERIO=yCONFIG_SERIO_I8042=yCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=ySo I guess your problem is not enabling the i8042 module.
This code will also hopefully be enabled in 2.5.26 (though it'll be optional with the old driver still there).
Quoted 1,092 lines · Ed Sweetman
Nope, failure. I'm not getting any reaction from the kernel at all about the keyboard. I'm including my config
Quoted 57 lines · Ed Sweetman
2.5.18 is the last time it worked for me I have basically the same exact config, the new input system seems to have undergone some changes since then though and now it's not behaving. I will try setting the XTKBD setting and PS2SEDKBD or whatever it is.
Quoted 30 lines · A Guy Called Tyketto
Quoted 5 lines · Ed Sweetman
Same config as in my last post about the issue linking with this kernel. I'm having my keyboard just not respond from boot. I've got Input Device support built in and i had it as module and the keyboard is ps/2. No idea what's going on here
Just a "me too" here.. I've had this problem since around 2.5.15-dj
and later, and have had input and keyboard support compiled into the kernel. Luckily I was able to get into the box via ssh, and check things. both keyboard and mouse are PS/2. If possible, see if you can do this, and check if IRQ 1 is not listed in/proc/interrupts. That is what is happening with me, while my mouse is working. For me to get my keyboard to work, I have to have the following set:
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=yCONFIG_INPUT_EVBUG=yCONFIG_SERIO=yCONFIG_SERIO_SERPORT=mCONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=yCONFIG_KEYBOARD_XTKBD=yCONFIG_INPUT_MOUSE=yCONFIG_MOUSE_PS2=yQuoted 18 lines
This leaves me without using the new Input API, but with a working
keyboard. with using the new API, mouse will work, keyboard will not. you can try these, and use the old setup (I assume will be made legacy by the time 2.6 comes out), and let me know if they work. The new API seems to be working for some people, but not all.BL.Signature · 10 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/Quoted 5 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/#
# Automatically generated make config: don't edit
#CONFIG_X86=y
#CONFIG_SBUSis not setCONFIG_UID16=y#
# Code maturity level options
#CONFIG_EXPERIMENTAL=y#
# General setup
#CONFIG_NET=yCONFIG_SYSVIPC=y
#CONFIG_BSD_PROCESS_ACCTis not setCONFIG_SYSCTL=y#
# Loadable module support
#CONFIG_MODULES=y
#CONFIG_MODVERSIONSis not setCONFIG_KMOD=y#
# Processor type and features
#
#CONFIG_M386is not set
#CONFIG_M486is not set
#CONFIG_M586is not set
#CONFIG_M586TSCis not set
#CONFIG_M586MMXis not set
#CONFIG_M686is not set
#CONFIG_MPENTIUMIIIis not setCONFIG_MPENTIUM4=y
#CONFIG_MK6is not set
#CONFIG_MK7is not set
#CONFIG_MELANis not set
#CONFIG_MCRUSOEis not set
#CONFIG_MWINCHIPC6is not set
#CONFIG_MWINCHIP2is not set
#CONFIG_MWINCHIP3Dis not set
#CONFIG_MCYRIXIIIis not setCONFIG_X86_WP_WORKS_OK=yCONFIG_X86_INVLPG=yCONFIG_X86_CMPXCHG=yCONFIG_X86_XADD=yCONFIG_X86_BSWAP=yCONFIG_X86_POPAD_OK=y
#CONFIG_RWSEM_GENERIC_SPINLOCKis not setCONFIG_RWSEM_XCHGADD_ALGORITHM=yCONFIG_X86_L1_CACHE_SHIFT=7CONFIG_X86_TSC=yCONFIG_X86_GOOD_APIC=yCONFIG_X86_USE_PPRO_CHECKSUM=y
#CONFIG_SMPis not setCONFIG_PREEMPT=yCONFIG_X86_UP_APIC=yCONFIG_X86_UP_IOAPIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_X86_IO_APIC=yCONFIG_X86_MCE=y
#CONFIG_X86_MCE_NONFATALis not setCONFIG_X86_MCE_P4THERMAL=y
#CONFIG_CPU_FREQis not set
#CONFIG_TOSHIBAis not set
#CONFIG_I8Kis not set
#CONFIG_MICROCODEis not setCONFIG_X86_MSR=mCONFIG_X86_CPUID=mCONFIG_NOHIGHMEM=y
#CONFIG_HIGHMEM4Gis not set
#CONFIG_HIGHMEM64Gis not set
#CONFIG_MATH_EMULATIONis not setCONFIG_MTRR=yCONFIG_HAVE_DEC_LOCK=y#
# Power management options (ACPI, APM)
##
# ACPI Support
#
#CONFIG_ACPIis not set
#CONFIG_PMis not set
#CONFIG_APMis not set
#CONFIG_SOFTWARE_SUSPENDis not set#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#CONFIG_PCI=y
#CONFIG_PCI_GOBIOSis not set
#CONFIG_PCI_GODIRECTis not setCONFIG_PCI_GOANY=yCONFIG_PCI_BIOS=yCONFIG_PCI_DIRECT=yCONFIG_PCI_NAMES=y
#CONFIG_ISAis not set
#CONFIG_EISAis not set
#CONFIG_MCAis not setCONFIG_HOTPLUG=y#
# PCMCIA/CardBus support
#
#CONFIG_PCMCIAis not set#
# PCI Hotplug Support
#
#CONFIG_HOTPLUG_PCIis not set
#CONFIG_HOTPLUG_PCI_COMPAQis not set
#CONFIG_HOTPLUG_PCI_COMPAQ_NVRAMis not set
#CONFIG_HOTPLUG_PCI_IBMis not set#
# Executable file formats
#CONFIG_KCORE_ELF=y
#CONFIG_KCORE_AOUTis not setCONFIG_BINFMT_AOUT=mCONFIG_BINFMT_ELF=yCONFIG_BINFMT_MISC=m
#CONFIG_IKCONFIGis not set#
# Memory Technology Devices (MTD)
#
#CONFIG_MTDis not set#
# Parallel port support
#
#CONFIG_PARPORTis not set#
# Plug and Play configuration
#
#CONFIG_PNPis not set
#CONFIG_ISAPNPis not set
#CONFIG_PNPBIOSis not set#
# Block devices
#CONFIG_BLK_DEV_FD=y
#CONFIG_BLK_DEV_XDis not set
#CONFIG_PARIDEis not set
#CONFIG_BLK_CPQ_DAis not set
#CONFIG_BLK_CPQ_CISS_DAis not set
#CONFIG_CISS_SCSI_TAPEis not set
#CONFIG_BLK_DEV_DAC960is not set
#CONFIG_BLK_DEV_UMEMis not setCONFIG_BLK_DEV_LOOP=m
#CONFIG_BLK_DEV_NBDis not set
#CONFIG_BLK_DEV_RAMis not set
#CONFIG_BLK_DEV_INITRDis not set#
# Multi-device support (RAID and LVM)
#
#CONFIG_MDis not set
#CONFIG_BLK_DEV_MDis not set
#CONFIG_MD_LINEARis not set
#CONFIG_MD_RAID0is not set
#CONFIG_MD_RAID1is not set
#CONFIG_MD_RAID5is not set
#CONFIG_MD_MULTIPATHis not set
#CONFIG_BLK_DEV_LVMis not set#
# Networking options
#CONFIG_PACKET=yCONFIG_PACKET_MMAP=y
#CONFIG_NETLINK_DEVis not set
#CONFIG_NETFILTERis not set
#CONFIG_FILTERis not setCONFIG_UNIX=yCONFIG_INET=y
#CONFIG_IP_MULTICASTis not set
#CONFIG_IP_ADVANCED_ROUTERis not set
#CONFIG_IP_PNPis not set
#CONFIG_NET_IPIPis not set
#CONFIG_NET_IPGREis not set
#CONFIG_ARPDis not set
#CONFIG_INET_ECNis not set
#CONFIG_SYN_COOKIESis not set
#CONFIG_IPV6is not set
#CONFIG_KHTTPDis not set
#CONFIG_ATMis not set
#CONFIG_VLAN_8021Qis not set#
#
#
#CONFIG_IPXis not set
#CONFIG_ATALKis not set#
# Appletalk devices
#
#CONFIG_DEV_APPLETALKis not set
#CONFIG_DECNETis not set
#CONFIG_BRIDGEis not set
#CONFIG_X25is not set
#CONFIG_LAPBis not set
#CONFIG_LLCis not set
#CONFIG_NET_DIVERTis not set
#CONFIG_ECONETis not set
#CONFIG_WAN_ROUTERis not set
#CONFIG_NET_FASTROUTEis not set
#CONFIG_NET_HW_FLOWCONTROLis not set#
# QoS and/or fair queueing
#
#CONFIG_NET_SCHEDis not set#
# Telephony Support
#
#CONFIG_PHONEis not set
#CONFIG_PHONE_IXJis not set
#CONFIG_PHONE_IXJ_PCMCIAis not set#
# ATA/IDE/MFM/RLL support
#CONFIG_IDE=y
#CONFIG_IDE_24is not setCONFIG_IDE_25=y#
# ATA and ATAPI Block devices
#CONFIG_BLK_DEV_IDE=y#
# Please seeDocumentation/ide.txtfor help/info on IDE drives #
#CONFIG_BLK_DEV_HD_IDEis not set
#CONFIG_BLK_DEV_HDis not setCONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=yCONFIG_IDEDISK_STROKE=y
#CONFIG_BLK_DEV_IDECSis not setCONFIG_BLK_DEV_IDECD=m
#CONFIG_BLK_DEV_IDETAPEis not set
#CONFIG_BLK_DEV_IDEFLOPPYis not setCONFIG_BLK_DEV_IDESCSI=m#
# ATA host chip set support
#
#CONFIG_BLK_DEV_CMD640is not set
#CONFIG_BLK_DEV_CMD640_ENHANCEDis not set
#CONFIG_BLK_DEV_ISAPNPis not set
#CONFIG_BLK_DEV_RZ1000is not set#
# PCI host chip set support
#
#CONFIG_BLK_DEV_OFFBOARDis not setCONFIG_IDEPCI_SHARE_IRQ=yCONFIG_BLK_DEV_IDEDMA_PCI=yCONFIG_IDEDMA_PCI_AUTO=y
#CONFIG_IDEDMA_ONLYDISKis not setCONFIG_BLK_DEV_IDEDMA=y
#CONFIG_BLK_DEV_IDE_TCQis not set
#CONFIG_BLK_DEV_IDE_TCQ_DEFAULTis not set
#CONFIG_IDEDMA_NEW_DRIVE_LISTINGSis not set
#CONFIG_BLK_DEV_AEC62XXis not set
#CONFIG_AEC6280_BURSTis not set
#CONFIG_BLK_DEV_ALI15X3is not set
#CONFIG_WDC_ALI15X3is not set
#CONFIG_BLK_DEV_AMD74XXis not set
#CONFIG_BLK_DEV_CMD64Xis not set
#CONFIG_BLK_DEV_CY82C693is not set
#CONFIG_BLK_DEV_CS5530is not set
#CONFIG_BLK_DEV_HPT34Xis not set
#CONFIG_HPT34X_AUTODMAis not set
#CONFIG_BLK_DEV_HPT366is not setCONFIG_BLK_DEV_PIIX=y
#CONFIG_BLK_DEV_NS87415is not set
#CONFIG_BLK_DEV_OPTI621is not set
#CONFIG_BLK_DEV_PDC202XXis not set
#CONFIG_PDC202XX_BURSTis not set
#CONFIG_PDC202XX_FORCEis not set
#CONFIG_BLK_DEV_SVWKSis not set
#CONFIG_BLK_DEV_SIS5513is not set
#CONFIG_BLK_DEV_TRM290is not set
#CONFIG_BLK_DEV_VIA82CXXXis not set
#CONFIG_BLK_DEV_SL82C105is not set
#CONFIG_IDE_CHIPSETSis not set
#CONFIG_IDEDMA_IVBis not setCONFIG_ATAPI=yCONFIG_IDEDMA_AUTO=y
#CONFIG_BLK_DEV_ATARAIDis not set
#CONFIG_BLK_DEV_ATARAID_PDCis not set
#CONFIG_BLK_DEV_ATARAID_HPTis not set#
# SCSI support
#CONFIG_SCSI=m#
# SCSI support type (disk, tape, CD-ROM)
#
#CONFIG_BROKEN_SCSI_ERROR_HANDLINGis not setCONFIG_BLK_DEV_SD=mCONFIG_SD_EXTRA_DEVS=40
#CONFIG_CHR_DEV_STis not set
#CONFIG_CHR_DEV_OSSTis not setCONFIG_BLK_DEV_SR=m
#CONFIG_BLK_DEV_SR_VENDORis not setCONFIG_SR_EXTRA_DEVS=2CONFIG_CHR_DEV_SG=m
#CONFIG_CHR_DEV_SMis not set#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #CONFIG_SCSI_MULTI_LUN=yCONFIG_SCSI_REPORT_LUNS=y
#CONFIG_SCSI_CONSTANTSis not set
#CONFIG_SCSI_LOGGINGis not set#
# SCSI low-level drivers
#
#CONFIG_BLK_DEV_3W_XXXX_RAIDis not set
#CONFIG_SCSI_7000FASSTis not set
#CONFIG_SCSI_ACARDis not set
#CONFIG_SCSI_AIC7XXXis not set
#CONFIG_SCSI_AIC7XXX_OLDis not set
#CONFIG_SCSI_DPT_I2Ois not set
#CONFIG_SCSI_ADVANSYSis not set
#CONFIG_SCSI_IN2000is not set
#CONFIG_SCSI_AM53C974is not set
#CONFIG_SCSI_MEGARAIDis not set
#CONFIG_SCSI_BUSLOGICis not set
#CONFIG_SCSI_CPQFCTSis not set
#CONFIG_SCSI_DMX3191Dis not set
#CONFIG_SCSI_DTC3280is not set
#CONFIG_SCSI_EATAis not set
#CONFIG_SCSI_EATA_DMAis not set
#CONFIG_SCSI_EATA_PIOis not set
#CONFIG_SCSI_FUTURE_DOMAINis not set
#CONFIG_SCSI_GDTHis not set
#CONFIG_SCSI_GENERIC_NCR5380is not set
#CONFIG_SCSI_IPSis not set
#CONFIG_SCSI_INITIOis not set
#CONFIG_SCSI_INIA100is not set
#CONFIG_SCSI_NCR53C406Ais not set
#CONFIG_SCSI_NCR53C7xxis not set
#CONFIG_SCSI_SYM53C8XX_2is not set
#CONFIG_SCSI_NCR53C8XXis not set
#CONFIG_SCSI_SYM53C8XXis not set
#CONFIG_SCSI_PAS16is not set
#CONFIG_SCSI_PCI2000is not set
#CONFIG_SCSI_PCI2220Iis not set
#CONFIG_SCSI_PSI240Iis not set
#CONFIG_SCSI_QLOGIC_FASis not set
#CONFIG_SCSI_QLOGIC_ISPis not set
#CONFIG_SCSI_QLOGIC_FCis not set
#CONFIG_SCSI_QLOGIC_1280is not set
#CONFIG_SCSI_SYM53C416is not set
#CONFIG_SCSI_DC390Tis not set
#CONFIG_SCSI_T128is not set
#CONFIG_SCSI_U14_34Fis not set
#CONFIG_SCSI_DEBUGis not set#
# Fusion MPT device support
#
#CONFIG_FUSIONis not set
#CONFIG_FUSION_BOOTis not set
#CONFIG_FUSION_ISENSEis not set
#CONFIG_FUSION_CTLis not set
#CONFIG_FUSION_LANis not set#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
#CONFIG_IEEE1394is not set#
# I2O device support
#
#CONFIG_I2Ois not set
#CONFIG_I2O_PCIis not set
#CONFIG_I2O_BLOCKis not set
#CONFIG_I2O_LANis not set
#CONFIG_I2O_SCSIis not set
#CONFIG_I2O_PROCis not set#
# Network device support
#CONFIG_NETDEVICES=y#
# ARCnet devices
#
#CONFIG_ARCNETis not setCONFIG_DUMMY=m
#CONFIG_BONDINGis not set
#CONFIG_EQUALIZERis not set
#CONFIG_TUNis not set
#CONFIG_ETHERTAPis not set#
# Ethernet (10 or 100Mbit)
#CONFIG_NET_ETHERNET=y
#CONFIG_SUNLANCEis not set
#CONFIG_HAPPYMEALis not set
#CONFIG_SUNBMACis not set
#CONFIG_SUNQEis not set
#CONFIG_SUNGEMis not set
#CONFIG_NET_VENDOR_3COMis not set
#CONFIG_LANCEis not set
#CONFIG_NET_VENDOR_SMCis not set
#CONFIG_NET_VENDOR_RACALis not set
#CONFIG_HP100is not set
#CONFIG_NET_ISAis not setCONFIG_NET_PCI=y
#CONFIG_PCNET32is not set
#CONFIG_ADAPTEC_STARFIREis not set
#CONFIG_APRICOTis not set
#CONFIG_CS89x0is not set
#CONFIG_DGRSis not setCONFIG_EEPRO100=mCONFIG_E100=m
#CONFIG_LNE390is not set
#CONFIG_FEALNXis not set
#CONFIG_NATSEMIis not set
#CONFIG_NE2K_PCIis not set
#CONFIG_NE3210is not set
#CONFIG_ES3210is not set
#CONFIG_8139CPis not set
#CONFIG_8139TOOis not set
#CONFIG_8139TOO_PIOis not set
#CONFIG_8139TOO_TUNE_TWISTERis not set
#CONFIG_8139TOO_8129is not set
#CONFIG_8139_NEW_RX_RESETis not set
#CONFIG_SIS900is not set
#CONFIG_EPIC100is not set
#CONFIG_SUNDANCEis not set
#CONFIG_TLANis not set
#CONFIG_VIA_RHINEis not set
#CONFIG_VIA_RHINE_MMIOis not set
#CONFIG_NET_POCKETis not set#
# Ethernet (1000 Mbit)
#
#CONFIG_ACENICis not set
#CONFIG_DL2Kis not set
#CONFIG_E1000is not set
#CONFIG_MYRI_SBUSis not set
#CONFIG_NS83820is not set
#CONFIG_HAMACHIis not set
#CONFIG_YELLOWFINis not set
#CONFIG_SK98LINis not set
#CONFIG_TIGON3is not set
#CONFIG_FDDIis not set
#CONFIG_HIPPIis not set
#CONFIG_PLIPis not set
#CONFIG_PPPis not set
#CONFIG_SLIPis not set#
# Wireless LAN (non-hamradio)
#
#CONFIG_NET_RADIOis not set#
# Token Ring devices
#
#CONFIG_TRis not set
#CONFIG_NET_FCis not set
#CONFIG_RCPCIis not set
#CONFIG_SHAPERis not set#
# Wan interfaces
#
#CONFIG_WANis not set#
# Tulip family network device support
#
#CONFIG_NET_TULIPis not set#
# Amateur Radio support
#
#CONFIG_HAMRADIOis not set#
# IrDA (infrared) support
#
#CONFIG_IRDAis not set#
# ISDN subsystem
#
#CONFIG_ISDN_BOOLis not set#
# Input device support
#CONFIG_INPUT=y#
# Userland interfaces
#CONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#CONFIG_INPUT_JOYDEVis not set
#CONFIG_INPUT_TSDEVis not setCONFIG_INPUT_EVDEV=y
#CONFIG_INPUT_EVBUGis not set#
# Input I/O drivers
#
#CONFIG_GAMEPORTis not setCONFIG_SOUND_GAMEPORT=y
#CONFIG_GAMEPORT_NS558is not set
#CONFIG_GAMEPORT_L4is not set
#CONFIG_GAMEPORT_EMU10K1is not set
#CONFIG_GAMEPORT_VORTEXis not set
#CONFIG_GAMEPORT_FM801is not set
#CONFIG_GAMEPORT_CS461Xis not setCONFIG_SERIO=y
#CONFIG_SERIO_I8042is not setCONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12
#CONFIG_SERIO_SERPORTis not set
#CONFIG_SERIO_CT82C710is not set
#CONFIG_SERIO_PARKBDis not set#
# Input Device Drivers
#CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=y
#CONFIG_KEYBOARD_SUNKBDis not set
#CONFIG_KEYBOARD_PS2SERKBDis not set
#CONFIG_KEYBOARD_XTKBDis not set
#CONFIG_INPUT_MOUSEis not set
#CONFIG_MOUSE_PS2is not set
#CONFIG_MOUSE_SERIALis not set
#CONFIG_MOUSE_INPORTis not set
#CONFIG_MOUSE_LOGIBMis not set
#CONFIG_MOUSE_PC110PADis not set
#CONFIG_INPUT_JOYSTICKis not set
#CONFIG_JOYSTICK_ANALOGis not set
#CONFIG_JOYSTICK_A3Dis not set
#CONFIG_JOYSTICK_ADIis not set
#CONFIG_JOYSTICK_COBRAis not set
#CONFIG_JOYSTICK_GF2Kis not set
#CONFIG_JOYSTICK_GRIPis not set
#CONFIG_JOYSTICK_GUILLEMOTis not set
#CONFIG_JOYSTICK_INTERACTis not set
#CONFIG_JOYSTICK_SIDEWINDERis not set
#CONFIG_JOYSTICK_TMDCis not set
#CONFIG_JOYSTICK_IFORCE_USBis not set
#CONFIG_JOYSTICK_IFORCE_232is not set
#CONFIG_JOYSTICK_WARRIORis not set
#CONFIG_JOYSTICK_MAGELLANis not set
#CONFIG_JOYSTICK_SPACEORBis not set
#CONFIG_JOYSTICK_SPACEBALLis not set
#CONFIG_JOYSTICK_STINGERis not set
#CONFIG_JOYSTICK_TWIDDLERis not set
#CONFIG_JOYSTICK_DB9is not set
#CONFIG_JOYSTICK_GAMECONis not set
#CONFIG_JOYSTICK_TURBOGRAFXis not set
#CONFIG_INPUT_TOUCHSCREENis not set
#CONFIG_TOUCHSCREEN_GUNZEis not set#
# Character devices
#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_SERIAL=y
#CONFIG_SERIAL_CONSOLEis not set
#CONFIG_SERIAL_EXTENDEDis not set
#CONFIG_SERIAL_NONSTANDARDis not setCONFIG_UNIX98_PTYS=yCONFIG_UNIX98_PTY_COUNT=256#
# I2C support
#CONFIG_I2C=mCONFIG_I2C_ALGOBIT=m
#CONFIG_I2C_PHILIPSPARis not set
#CONFIG_I2C_ELVis not set
#CONFIG_I2C_VELLEMANis not set
#CONFIG_I2C_ALGOPCFis not setCONFIG_I2C_CHARDEV=mCONFIG_I2C_PROC=m
#CONFIG_QIC02_TAPEis not set#
# Watchdog Cards
#
#CONFIG_WATCHDOGis not set
#CONFIG_AMD_RNGis not setCONFIG_INTEL_RNG=y
#CONFIG_NVRAMis not setCONFIG_RTC=y
#CONFIG_DTLKis not set
#CONFIG_R3964is not set
#CONFIG_APPLICOMis not set
#CONFIG_SONYPIis not set#
# Ftape, the floppy tape device driver
#
#CONFIG_FTAPEis not setCONFIG_AGP=yCONFIG_AGP_INTEL=y
#CONFIG_AGP_I810is not set
#CONFIG_AGP_VIAis not set
#CONFIG_AGP_AMDis not set
#CONFIG_AGP_SISis not set
#CONFIG_AGP_ALIis not set
#CONFIG_AGP_SWORKSis not setCONFIG_DRM=y
#CONFIG_DRM_TDFXis not set
#CONFIG_DRM_GAMMAis not set
#CONFIG_DRM_R128is not set
#CONFIG_DRM_RADEONis not set
#CONFIG_DRM_I810is not set
#CONFIG_DRM_I830is not set
#CONFIG_DRM_MGAis not set
#CONFIG_DRM_SISis not set
#CONFIG_MWAVEis not set#
# Multimedia devices
#
#CONFIG_VIDEO_DEVis not set#
# File systems
#
#CONFIG_QUOTAis not set
#CONFIG_QFMT_V1is not set
#CONFIG_QFMT_V2is not set
#CONFIG_AUTOFS_FSis not setCONFIG_AUTOFS4_FS=y
#CONFIG_REISERFS_FSis not set
#CONFIG_REISERFS_CHECKis not set
#CONFIG_REISERFS_PROC_INFOis not set
#CONFIG_ADFS_FSis not set
#CONFIG_ADFS_FS_RWis not set
#CONFIG_AFFS_FSis not set
#CONFIG_HFS_FSis not set
#CONFIG_BFS_FSis not setCONFIG_EXT3_FS=yCONFIG_JBD=y
#CONFIG_JBD_DEBUGis not setCONFIG_FAT_FS=mCONFIG_MSDOS_FS=m
#CONFIG_UMSDOS_FSis not setCONFIG_VFAT_FS=m
#CONFIG_EFS_FSis not set
#CONFIG_JFFS_FSis not set
#CONFIG_JFFS2_FSis not set
#CONFIG_CRAMFSis not set
#CONFIG_TMPFSis not setCONFIG_RAMFS=yCONFIG_ISO9660_FS=mCONFIG_JOLIET=y
#CONFIG_ZISOFSis not set
#CONFIG_JFS_FSis not set
#CONFIG_JFS_DEBUGis not set
#CONFIG_JFS_STATISTICSis not set
#CONFIG_MINIX_FSis not set
#CONFIG_VXFS_FSis not set
#CONFIG_NTFS_FSis not set
#CONFIG_NTFS_DEBUGis not set
#CONFIG_HPFS_FSis not setCONFIG_PROC_FS=yCONFIG_DEVFS_FS=yCONFIG_DEVFS_MOUNT=y
#CONFIG_DEVFS_DEBUGis not set
#CONFIG_DEVPTS_FSis not set
#CONFIG_QNX4FS_FSis not set
#CONFIG_QNX4FS_RWis not set
#CONFIG_ROMFS_FSis not setCONFIG_EXT2_FS=m
#CONFIG_SYSV_FSis not set
#CONFIG_UDF_FSis not set
#CONFIG_UDF_RWis not set
#CONFIG_UFS_FSis not set
#CONFIG_UFS_FS_WRITEis not set#
# Network File Systems
#
#CONFIG_CODA_FSis not set
#CONFIG_INTERMEZZO_FSis not set
#CONFIG_NFS_FSis not set
#CONFIG_NFS_V3is not set
#CONFIG_ROOT_NFSis not set
#CONFIG_NFSDis not set
#CONFIG_NFSD_V3is not set
#CONFIG_NFSD_TCPis not set
#CONFIG_SUNRPCis not set
#CONFIG_LOCKDis not set
#CONFIG_EXPORTFSis not setCONFIG_SMB_FS=y
#CONFIG_SMB_NLS_DEFAULTis not set
#CONFIG_NCP_FSis not set
#CONFIG_NCPFS_PACKET_SIGNINGis not set
#CONFIG_NCPFS_IOCTL_LOCKINGis not set
#CONFIG_NCPFS_STRONGis not set
#CONFIG_NCPFS_NFS_NSis not set
#CONFIG_NCPFS_OS2_NSis not set
#CONFIG_NCPFS_SMALLDOSis not set
#CONFIG_NCPFS_NLSis not set
#CONFIG_NCPFS_EXTRASis not set
#CONFIG_ZISOFS_FSis not set#
# Partition Types
#
#CONFIG_PARTITION_ADVANCEDis not setCONFIG_MSDOS_PARTITION=yCONFIG_SMB_NLS=yCONFIG_NLS=y#
# Native Language Support
#CONFIG_NLS_DEFAULT="iso8859-1"CONFIG_NLS_CODEPAGE_437=y
#CONFIG_NLS_CODEPAGE_737is not set
#CONFIG_NLS_CODEPAGE_775is not set
#CONFIG_NLS_CODEPAGE_850is not set
#CONFIG_NLS_CODEPAGE_852is not set
#CONFIG_NLS_CODEPAGE_855is not set
#CONFIG_NLS_CODEPAGE_857is not set
#CONFIG_NLS_CODEPAGE_860is not set
#CONFIG_NLS_CODEPAGE_861is not set
#CONFIG_NLS_CODEPAGE_862is not set
#CONFIG_NLS_CODEPAGE_863is not set
#CONFIG_NLS_CODEPAGE_864is not set
#CONFIG_NLS_CODEPAGE_865is not set
#CONFIG_NLS_CODEPAGE_866is not set
#CONFIG_NLS_CODEPAGE_869is not set
#CONFIG_NLS_CODEPAGE_936is not set
#CONFIG_NLS_CODEPAGE_950is not set
#CONFIG_NLS_CODEPAGE_932is not set
#CONFIG_NLS_CODEPAGE_949is not set
#CONFIG_NLS_CODEPAGE_874is not set
#CONFIG_NLS_ISO8859_8is not set
#CONFIG_NLS_CODEPAGE_1250is not set
#CONFIG_NLS_CODEPAGE_1251is not setCONFIG_NLS_ISO8859_1=y
#CONFIG_NLS_ISO8859_2is not set
#CONFIG_NLS_ISO8859_3is not set
#CONFIG_NLS_ISO8859_4is not set
#CONFIG_NLS_ISO8859_5is not set
#CONFIG_NLS_ISO8859_6is not set
#CONFIG_NLS_ISO8859_7is not set
#CONFIG_NLS_ISO8859_9is not set
#CONFIG_NLS_ISO8859_13is not set
#CONFIG_NLS_ISO8859_14is not set
#CONFIG_NLS_ISO8859_15is not set
#CONFIG_NLS_KOI8_Ris not set
#CONFIG_NLS_KOI8_Uis not set
#CONFIG_NLS_UTF8is not set#
# Console drivers
#CONFIG_VGA_CONSOLE=yCONFIG_VIDEO_SELECT=y
#CONFIG_MDA_CONSOLEis not set#
# Frame-buffer support
#
#CONFIG_FBis not set#
# Sound
#CONFIG_SOUND=m#
# Open Sound System
#
#CONFIG_SOUND_PRIMEis not set#
# Advanced Linux Sound Architecture
#CONFIG_SND=m
#CONFIG_SND_SEQUENCERis not setCONFIG_SND_OSSEMUL=yCONFIG_SND_MIXER_OSS=mCONFIG_SND_PCM_OSS=m
#CONFIG_SND_SEQUENCER_OSSis not setCONFIG_SND_RTCTIMER=m
#CONFIG_SND_VERBOSE_PRINTKis not set
#CONFIG_SND_DEBUGis not set
#CONFIG_SND_DEBUG_MEMORYis not set
#CONFIG_SND_DEBUG_DETECTis not set#
# Generic devices
#
#CONFIG_SND_DUMMYis not set
#CONFIG_SND_VIRMIDIis not set
#CONFIG_SND_MTPAVis not set
#CONFIG_SND_SERIAL_U16550is not set
#CONFIG_SND_MPU401is not set#
# PCI devices
#
#CONFIG_SND_ALI5451is not set
#CONFIG_SND_CS46XXis not setCONFIG_SND_EMU10K1=m
#CONFIG_SND_KORG1212is not set
#CONFIG_SND_NM256is not set
#CONFIG_SND_RME32is not set
#CONFIG_SND_RME96is not set
#CONFIG_SND_RME9652is not set
#CONFIG_SND_HDSPis not set
#CONFIG_SND_TRIDENTis not set
#CONFIG_SND_YMFPCIis not set
#CONFIG_SND_ALS4000is not set
#CONFIG_SND_CMIPCIis not set
#CONFIG_SND_ENS1370is not set
#CONFIG_SND_ENS1371is not set
#CONFIG_SND_ES1938is not set
#CONFIG_SND_ES1968is not set
#CONFIG_SND_MAESTRO3is not set
#CONFIG_SND_FM801is not set
#CONFIG_SND_ICE1712is not set
#CONFIG_SND_INTEL8X0is not set
#CONFIG_SND_SONICVIBESis not set
#CONFIG_SND_VIA686is not set
#CONFIG_SND_VIA8233is not set#
# USB support
#CONFIG_USB=m
#CONFIG_USB_DEBUGis not set#
# Miscellaneous USB options
#CONFIG_USB_DEVICEFS=yCONFIG_USB_LONG_TIMEOUT=y
#CONFIG_USB_BANDWIDTHis not set
#CONFIG_USB_DYNAMIC_MINORSis not set#
# USB Host Controller Drivers
#
#CONFIG_USB_EHCI_HCDis not set
#CONFIG_USB_OHCI_HCDis not setCONFIG_USB_UHCI_HCD_ALT=m#
# USB Device Class drivers
#
#CONFIG_USB_AUDIOis not set
#CONFIG_USB_BLUETOOTH_TTYis not set
#CONFIG_USB_MIDIis not set
#CONFIG_USB_ACMis not set
#CONFIG_USB_PRINTERis not setCONFIG_USB_STORAGE=m
#CONFIG_USB_STORAGE_DEBUGis not set
#CONFIG_USB_STORAGE_DATAFABis not set
#CONFIG_USB_STORAGE_FREECOMis not set
#CONFIG_USB_STORAGE_ISD200is not set
#CONFIG_USB_STORAGE_DPCMis not set
#CONFIG_USB_STORAGE_HP8200eis not set
#CONFIG_USB_STORAGE_SDDR09is not set
#CONFIG_USB_STORAGE_SDDR55is not set
#CONFIG_USB_STORAGE_JUMPSHOTis not set#
# USB Human Interface Devices (HID)
#CONFIG_USB_HID=mCONFIG_USB_HIDINPUT=y
#CONFIG_USB_HIDDEVis not set
#CONFIG_USB_KBDis not set
#CONFIG_USB_MOUSEis not set
#CONFIG_USB_AIPTEKis not set
#CONFIG_USB_WACOMis not set#
# USB Imaging devices
#
#CONFIG_USB_MDC800is not set
#CONFIG_USB_SCANNERis not set
#CONFIG_USB_MICROTEKis not set
#CONFIG_USB_HPUSBSCSIis not set#
# USB Multimedia devices
#
#CONFIG_USB_DABUSBis not set#
# Video4Linux support is needed for USB Multimedia device support
#
#CONFIG_USB_VICAMis not set
#CONFIG_USB_DSBRis not set
#CONFIG_USB_IBMCAMis not set
#CONFIG_USB_KONICAWCis not set
#CONFIG_USB_OV511is not set
#CONFIG_USB_PWCis not set
#CONFIG_USB_SE401is not set
#CONFIG_USB_STV680is not set#
# USB Network adaptors
#
#CONFIG_USB_CATCis not set
#CONFIG_USB_CDCETHERis not set
#CONFIG_USB_KAWETHis not set
#CONFIG_USB_PEGASUSis not set
#CONFIG_USB_RTL8150is not set
#CONFIG_USB_USBNETis not set#
# USB port drivers
#
#CONFIG_USB_USS720is not set#
# USB Serial Converter support
#
#CONFIG_USB_SERIALis not set
#CONFIG_USB_SERIAL_GENERICis not set
#CONFIG_USB_SERIAL_BELKINis not set
#CONFIG_USB_SERIAL_WHITEHEATis not set
#CONFIG_USB_SERIAL_DIGI_ACCELEPORTis not set
#CONFIG_USB_SERIAL_EMPEGis not set
#CONFIG_USB_SERIAL_FTDI_SIOis not set
#CONFIG_USB_SERIAL_VISORis not set
#CONFIG_USB_SERIAL_IPAQis not set
#CONFIG_USB_SERIAL_IRis not set
#CONFIG_USB_SERIAL_EDGEPORTis not set
#CONFIG_USB_SERIAL_KEYSPAN_PDAis not set
#CONFIG_USB_SERIAL_KEYSPANis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28is not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28Xis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28XAis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA28XBis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19is not set
#CONFIG_USB_SERIAL_KEYSPAN_USA18Xis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19Wis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19QWis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA19QIis not set
#CONFIG_USB_SERIAL_KEYSPAN_USA49Wis not set
#CONFIG_USB_SERIAL_KLSIis not set
#CONFIG_USB_SERIAL_MCT_U232is not set
#CONFIG_USB_SERIAL_PL2303is not set
#CONFIG_USB_SERIAL_SAFEis not set
#CONFIG_USB_SERIAL_SAFE_PADDEDis not set
#CONFIG_USB_SERIAL_CYBERJACKis not set
#CONFIG_USB_SERIAL_XIRCOMis not set
#CONFIG_USB_SERIAL_OMNINETis not set#
# USB Miscellaneous drivers
#
#CONFIG_USB_EMI26is not set
#CONFIG_USB_TIGLis not set
#CONFIG_USB_AUERSWALDis not set
#CONFIG_USB_RIO500is not set
#CONFIG_USB_BRLVGERis not set#
# Bluetooth support
#
#CONFIG_BLUEZis not set#
# Kernel hacking
#CONFIG_DEBUG_KERNEL=y
#CONFIG_DEBUG_OBSOLETEis not set
#CONFIG_DEBUG_SLABis not set
#CONFIG_DEBUG_IOVIRTis not setCONFIG_MAGIC_SYSRQ=y
#CONFIG_DEBUG_SPINLOCKis not set
#CONFIG_DEBUG_486_STRINGis not set
#CONFIG_FRAME_POINTERis not set#
# Library routines
#CONFIG_CRC32=y
#CONFIG_ZLIB_INFLATEis not set
#CONFIG_ZLIB_DEFLATEis not setSignature · 7 lines
Vojtech Pavlik SuSE Labs - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Signature · 3 lines
Alexander Hoogerhuis | [email protected] CCNP - CCDP - MCNE - CCSE | +47 908 21 485 "You have zero privacy anyway. Get over it." --Scott McNealy
Quoted 4 lines · Alexander Hoogerhuis
I mentioned this before, but I had major pains with the new input drivers for keyboards not working with the Comapq Armada M700's, and gave that up. Now I got a new Compaq N800c, which forced me onto 2.5.x because of some of the hardware (Intel ICH3 et al).
As I reported earlier (but appearantly unnoticed), on my Thinkpad A30p (which uses the ICH3), keyboard and mouse don't work with the new input layer when CONFIG_X86_UP_IOAPIC is on, but I have no problems (except my USB mouse) when I switch that off.
Quoted 5 lines
I only have two problems left is that I have a laptop with both a stick and a glidepad, and the psmouse driver only enables the pad, and not the stick. The other is that the rpm command segfaults for no apparent reason under 2.5.x (tried .23, 24., and .25 and -dj varieties of them). Same also happens with vim, second time it edits a file.
For me, the usb mouse stopped working with 2.5.25 in all configurations I tried, the stick works without UP_IOAPIC. Unless the new input driver is supposed to be a complete drop-in replacement for the old one, I still assume that is a configuration error on my side.
Quoted 2 lines
Quoted 2 lines · Ed Sweetman
Quoted 1 line
CONFIG_X86_UP_IOAPIC=y
Yup, Ed has this one on as well. Alexander, what about your systems?
Arnd <><
Quoted 17 lines · Arnd Bergmann
Quoted 4 lines · Alexander Hoogerhuis
I mentioned this before, but I had major pains with the new input drivers for keyboards not working with the Comapq Armada M700's, and gave that up. Now I got a new Compaq N800c, which forced me onto 2.5.x because of some of the hardware (Intel ICH3 et al).
As I reported earlier (but appearantly unnoticed), on my Thinkpad A30p (which uses the ICH3), keyboard and mouse don't work with the new input layer when
CONFIG_X86_UP_IOAPICis on, but I have no problems (except my USB mouse) when I switch that off.Quoted 5 lines
I only have two problems left is that I have a laptop with both a stick and a glidepad, and the psmouse driver only enables the pad, and not the stick. The other is that the rpm command segfaults for no apparent reason under 2.5.x (tried .23, 24., and .25 and -dj varieties of them). Same also happens with vim, second time it edits a file.
Quoted 5 lines
For me, the usb mouse stopped working with 2.5.25 in all configurations I tried, the stick works without
UP_IOAPIC. Unless the new input driver is supposed to be a complete drop-in replacement for the old one, I still assume that is a configuration error on my side.
I have it configured in, but it claims it dont have one at boot time (and I honestly dont know if the the hardware is physically in the box):
No local APIC present or hardware disabled
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines · Ed Sweetman
Quoted 1 line
CONFIG_X86_UP_IOAPIC=yYup, Ed has this one on as well. Alexander, what about your systems?
CONFIG_X86_GOOD_APIC=yCONFIG_X86_UP_APIC=yCONFIG_X86_UP_IOAPIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_X86_IO_APIC=y
Quoted 2 lines
Arnd <><
mvh,
A
Signature · 3 lines
Alexander Hoogerhuis | [email protected] CCNP - CCDP - MCNE - CCSE | +47 908 21 485 "You have zero privacy anyway. Get over it." --Scott McNealy
Quoted 4 lines · Ed Sweetman
Nope, failure. I'm not getting any reaction from the kernel at all about the keyboard. I'm including my config
You have network support compiled in. Are you able to get into the box
remotely (ssh, telnet, etc)? If so, get onto the box, and mail me the output of `cat /proc/interrupts. I'd like to confirm something that's on my end as well. my guess is that IRQ 1 is not listed. Another thing I should mention:
I'm encountering this problem with 2.5.25, though I reported this in the 2.5.20-dj tree. Vanilla 2.5.25 still has the legacy API there, so I'm able to fall back on that. I haven't run a -dj kernel since 2.5.20-dj3.
Quoted 11 lines
CONFIG_INPUT=y
#
# Userland interfaces
#CONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=y
#CONFIG_INPUT_EVBUGis not set
Quoted 2 lines
CONFIG_SERIO=y
#CONFIG_SERIO_I8042is not set
IIRC, CONFIG_SERIO_I8042 must be set for you to have a keyboard
present. This is the chipset that the keyboard and mouse use. This has to be set to y.
Quoted 3 lines
CONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12
Rest looks fine. give that a go, and see what you get.
BL.
Signature · 4 lines
Brad Littlejohn | Email: [email protected] Unix Systems Administrator, | [email protected] Web + NewsMaster, BOFH.. Smeghead! :) | http://www.wizard.com/~tyketto PGP: 1024D/E319F0BF 6980 AAD6 7329 E9E6 D569 F620 C819 199A E319 F0BF
Quoted 11 lines · A Guy Called Tyketto
Quoted 2 lines · Ed Sweetman
Nope, failure. I'm not getting any reaction from the kernel at all about the keyboard. I'm including my config
You have network support compiled in. Are you able to get into the box
remotely (ssh, telnet, etc)? If so, get onto the box, and mail me the output of `cat/proc/interrupts. I'd like to confirm something that's on my end as well. my guess is that IRQ 1 is not listed. Another thing I should mention:
I'm encountering this problem with 2.5.25, though I reported this in the 2.5.20-dj tree. Vanilla 2.5.25 still has the legacy API there, so I'm able to fall back on that.
Vanilla 2.5.25 still uses the original driver even if the new one was enabled. It isn't removed there. If both are enabled, they won't work.
-dj trees have the old driver removed, so the new one can work. In 2.5.26 (or http://linux-input.bkbits.net:8080/linux-input) the new driver config option will disable the old one.
Quoted 25 lines
I haven't run a -dj kernel since 2.5.20-dj3.
Quoted 11 lines
CONFIG_INPUT=y
#
# Userland interfaces
#CONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=y
#CONFIG_INPUT_EVBUGis not setQuoted 2 lines
CONFIG_SERIO=y
#CONFIG_SERIO_I8042is not setIIRC,
CONFIG_SERIO_I8042must be set for you to have a keyboard
present. This is the chipset that the keyboard and mouse use. This has to be set to y.Quoted 3 lines
CONFIG_I8042_REG_BASE=60CONFIG_I8042_KBD_IRQ=1CONFIG_I8042_AUX_IRQ=12Rest looks fine. give that a go, and see what you get.
Signature · 2 lines
Vojtech Pavlik SuSE Labs
Quoted 8 lines · A Guy Called Tyketto
Just a "me too" here.. I've had this problem since around 2.5.15-dj
and later, and have had input and keyboard support compiled into the kernel. Luckily I was able to get into the box via ssh, and check things. both keyboard and mouse are PS/2. If possible, see if you can do this, and check if IRQ 1 is not listed in/proc/interrupts. That is what is happening with me, while my mouse is working. For me to get my keyboard to work, I have to have the following set:
Quoted 9 lines
CONFIG_INPUT=yCONFIG_INPUT_KEYBDEV=yCONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_EVDEV=yCONFIG_INPUT_EVBUG=yCONFIG_SERIO=yCONFIG_SERIO_SERPORT=m
You're missing support for the actual PS/2 hardware itself; you've got support for the PS/2 keyboard protocol and keyboard device, but nothing to actually talk to the physical hardware. You probably want to turn on:
dep_tristate ' i8042 PC Keyboard controller' CONFIG_SERIO_I8042 $CONFIG_SERIO $CONFIG_ISA
Signature · 2 lines
Russell King ([email protected]) The developer of ARM Linux http://www.arm.linux.org.uk/personal/aboutme.html