ide drive dying?
Hello kernel people,
Kernel running: 2.4.20-pre1ac3 or -pre5ac2 (same under both)
Today I discovered a stale copy of qt-3.0.3 lying about on my disk. When I tried to delete it, this started showing up in my log files:
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070: reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 612672 0x0 SD]
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070: reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 612677 0x0 SD]
and rm just reported me 'Permission denied'.
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Thanks!
DK
Signature · 3 lines
If all the Chinese simultaneously jumped into the Pacific off a 10 foot platform erected 10 feet off their coast, it would cause a tidal wave that would destroy everything in this country west of Nebraska.
Quoted 2 lines
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
IBM DeathStar 75gxp.
One of the worst hard drives ever made. It's quite likely it's failed, and in fact, two years is pretty impressive out of one of these.
Make backups immediately. Run ibm's DFT tool, get the code to RMA this thing back to IBM. Sell the replacement they send you to a sucker on eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
Mike
Quoted 4 lines · Mike Dresser
eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
At current drive density and reliabilities - raid. Software raid setups are so cheap there is little point not running RAID on IDE nowdays
Quoted 9 lines · Alan Cox
Quoted 4 lines · Mike Dresser
eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
At current drive density and reliabilities - raid. Software raid setups are so cheap there is little point not running RAID on IDE nowdays
Well, I was looking more on the side of the Windows PC's here at the office, it's a bit expensive to start running raid on those.
Mike
Quoted 8 lines · Mike Dresser
Quoted 6 lines · Alan Cox
Quoted 4 lines · Mike Dresser
eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
Quoted 7 lines
Quoted 3 lines
At current drive density and reliabilities - raid. Software raid setups are so cheap there is little point not running RAID on IDE nowdays
Well, I was looking more on the side of the Windows PC's here at the office, it's a bit expensive to start running raid on those.
Mike
Well, I haven't examined this empirically, but as the quantity of disk drives in an organization continues increasing, so does the probability of disk failure, any one of which can mean lost time/money, etc. Drive reliability is likely not increasing at the same rate that density is, so the likelihood of lost data is probably increasing. Since LAN speeds continue to increase, it might start making sense now in clusters of more than a few machines to make each machine less reliant on its own disk storage (to the point of not at all other than big swap space) and use the LAN more. On the LAN put the money into a quality shared resource - a heavy duty UPS'd, etc. RAID system. Especially if a RAID system is as easy to build/maintain/use as Alan alludes to (don't know - never built one).
Billy
Quoted 6 lines · Billy Harvey
use the LAN more. On the LAN put the money into a quality shared resource - a heavy duty UPS'd, etc. RAID system. Especially if a RAID system is as easy to build/maintain/use as Alan alludes to (don't know - never built one).
Billy
And don't forget the cost of cluebats to beat the users over the head with. I've been trying for 3 years to get people to save their documents to the H: drive. Still find stuff stored wherever they feel like storing it.
So each facility has a backup server that nightly grabs their entire drive, gzip's it, and then dumps it to a DDS-4 tape. Also keeps X days of daily full backups, and X weeks as well.
Aside from Windows filesharing being so slow(1500kps via smbtar is average here), it works quite nicely. Even with a P4/2.53, I still can't get more than the 1500kps that a p133 is capable of. All the p4 gives me, is the ability to gzip -9 or even bzip2 the files, instead of the gzip -1 that the p133 is capable of in real time.
Mike
Quoted 17 lines · Mike Dresser
Quoted 8 lines · Alan Cox
Quoted 7 lines · Mike Dresser
Quoted 4 lines
eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
Quoted 7 lines
Quoted 3 lines
At current drive density and reliabilities - raid. Software raid setups are so cheap there is little point not running RAID on IDE nowdays
Well, I was looking more on the side of the Windows PC's here at the office, it's a bit expensive to start running raid on those.
Mike
Quoted 12 lines
Well, I haven't examined this empirically, but as the quantity of disk drives in an organization continues increasing, so does the probability of disk failure, any one of which can mean lost time/money, etc. Drive reliability is likely not increasing at the same rate that density is, so the likelihood of lost data is probably increasing. Since LAN speeds continue to increase, it might start making sense now in clusters of more than a few machines to make each machine less reliant on its own disk storage (to the point of not at all other than big swap space) and use the LAN more. On the LAN put the money into a quality shared resource - a heavy duty UPS'd, etc. RAID system. Especially if a RAID system is as easy to build/maintain/use as Alan alludes to (don't know - never built one).
A RAID array isn't a universal solution to all disk related problems, though, is it? I mean, we were talking about buggy firmware earlier on in this thread - if a drive which is part of an array returns corrupted data, without acknowledging it, then you'll read corrupted data from the RAID array. Also, an array of unreliable drives doesn't make a reliable array.
Now that the Smart Suite S.M.A.R.T. applications are unmaintained, would there be any chance of implementing S.M.A.R.T. in to the kernel IDE code? I know the IDE code is already a nightmare, but it would be a nice feature. S.M.A.R.T. is terribly under used at the moment - most people don't even know what it is. Infact, I could be wrong, but isn't a subset of S.M.A.R.T. implemented on modern SCSI disks, too?
Monitoring of any kind is always a nice feature to have...
John.
Quoted 1 line · On Fri, 6 Sep 2002 [email protected] wrote:
Infact, I could be wrong, but isn't a subset of S.M.A.R.T. implemented
on modern SCSI disks, too?
Yes.
Mike
Quoted 8 lines · Mike Dresser
Quoted 2 lines
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
IBM DeathStar 75gxp.
One of the worst hard drives ever made. It's quite likely it's failed, and in fact, two years is pretty impressive out of one of these.
Quoted 9 lines
Make backups immediately. Run ibm's DFT tool, get the code to RMA this thing back to IBM. Sell the replacement they send you to a sucker on eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
Mike
IBM DeathStar 75gxp.
Well put. Also, don't turn off this drive --ever. If possible, back-up to something on a network, not to anything on the IDE bus. If you don't have anything available, borrow something from work and make a temporary LAN. With bad sectors and a relocation list already full, this drive will seize the IDE bus and never let go once you trip it into failure.
Cheers,
Dick Johnson
Penguin : Linux version 2.4.18 on an i686 machine (797.90 BogoMips). The US military has given us many words, FUBAR, SNAFU, now ENRON. Yes, top management were graduates of West Point and Annapolis.
Quoted 4 lines · Richard B. Johnson
IBM DeathStar 75gxp.
Well put. Also, don't turn off this drive --ever. If possible, back-up to something on a network, not to anything on the IDE bus.
I had one of these drives fail recently with the dread "clicking of death" sounds (while it was retrying reads). What I discovered, while backing up the disk, is that continuing sequential reads past the bad sectors without and intervening operation would eventually cause the drive to get into a messed up state where it erroneously reported the following good sectors as bad.
My strategy to recover the good data was to read sequentially until I got an error, then explicitly seek to the next good sector and continue from there. This enabled me to copy the good data.
Am Fre, 2002-09-06 um 17.26 schrieb Mike Dresser:
Quoted 6 lines
Make backups immediately. Run ibm's DFT tool, get the code to RMA this thing back to IBM. Sell the replacement they send you to a sucker on eBAY, and buy yourself a new drive. You can pickup 80 gig drives for around 80 bucks nowadays. I used to recommend Maxtors, until they said they're cutting their warranty to one year from three. I don't know what to use anymore.
I did exactly this and bought a 80gig Maxtor for EUR 100 (don't know why it would be so much cheaper at your place, but anyway). Unfortunately the drive was broken right away, let's see how long the replacement drive keeps running...
Seems like every major brand is just producing crap nowadays....
Signature · 2 lines
Servus,
DanielQuoted 8 lines
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Have a look at:
http://csl.cse.ucsc.edu/smart.shtml
there you will find software for interrogating and monitoring the S.M.A.R.T. data available from your drive. It's a little late to start monitoring it, if the drive is already dying, but if, for example, it shows a lot of re-allocated sectors, or spin retries, you'll know something is wrong.
John.
Quoted 11 lines · On Friday 06 September 2002 17:36, [email protected] wrote:
Quoted 8 lines
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Have a look at:
Quoted 8 lines
http://csl.cse.ucsc.edu/smart.shtml
there you will find software for interrogating and monitoring the S.M.A.R.T. data available from your drive. It's a little late to start monitoring it, if the drive is already dying, but if, for example, it shows a lot of re-allocated sectors, or spin retries, you'll know something is wrong.
OK, I downloaded that and installed it, but well, frankly, it shows me very little useful stuff.
Or i'm just not good at interpreting this.
DK
Signature · 3 lines
"I gained nothing at all from Supreme Enlightenment, and for that very reason it is called Supreme Enlightenment." -- Gotama Buddha
Quoted 4 lines
OK, I downloaded that and installed it, but well, frankly, it shows me very little useful stuff.
Or i'm just not good at interpreting this.
Post the output of smartctl -a /dev/hda? to me, and I'll tell you what I can, but it's best to monitor the stats from when the drive is new, (I.E. every drive you buy from now on :-) ).
John.
Quoted 9 lines · On Friday 06 September 2002 19:22, [email protected] wrote:
Quoted 4 lines
OK, I downloaded that and installed it, but well, frankly, it shows me very little useful stuff.
Or i'm just not good at interpreting this.
Post the output of smartctl -a
/dev/hda? to me, and I'll tell you what I can, but it's best to monitor the stats from when the drive is new, (I.E. every drive you buy from now on :-) ).
Well, there were 21 ATA errors, and it showed 5 error blocks, with disk 'live' times of 629 hours.
Luckely I've been able to backup everything from the disk, and I'm running the DFT now. The tests showed bad sectors, i'm currently running a disk erase.
DK
Signature · 5 lines
"What's that thing?" "Well, it's a highly technical, sensitive instrument we use in computer repair. Being a layman, you probably can't grasp exactly what it does. We call it a two-by-four." -- Jeff MacNelley, "Shoe"
Quoted 1 line · DevilKin
Luckely I've been able to backup everything from the disk, and I'm running the DFT now. The tests showed bad sectors, i'm currently running a disk erase.
I have had sucess in firmware-upgrading these drives, after which all problems were gone forever.
You can download the firmware programs from http://anders.fugmann.dhs.org/ibm. There are both upgrade for 75GXP and 60GXP, or you could contact IBM for the firmware upgrade - They are not available on the ibm site. The programs are Windows thingies, which creates a floppy to be booted.
Regards
Anders Fugmann
On Sat, 07 Sep 2002 11:30:01 +0200 Anders Fugmann (AF) wrote:
AF> You can download the firmware programs from
AF> http://anders.fugmann.dhs.org/ibm. There are both upgrade for 75GXP and AF> 60GXP, or you could contact IBM for the firmware upgrade - They are not AF> available on the ibm site. The programs are Windows thingies, which AF> creates a floppy to be booted.
They are on the IBM site, but a bit hard to find:
http://www-1.ibm.com/support/docview.wss?rs=0&uid=psg1MIGR-39082
-Udo.
Quoted 2 lines · Anders Fugmann
I have had sucess in firmware-upgrading these drives, after which all problems were gone forever.
Which firmware version do your drives show? I ran the firmware upgrade on my two DTLA half a year ago, and ended up with this:
Model=IBM-DTLA-307045, FwRev=TX6OA59A
Model=IBM-DTLA-305040, FwRev=TW4OA69A
(from hdparm -i output - the former 0A changed to 9A after the upgrade, rest stayed the same)
Both work fine (they never failed me before the upgrade either). However, at least the second drive still clicks often enough for me to notice. I am still worried, though smartsuite says I'm fine - if I read the output correctly.
It seems to click only when doing lots of write requests for extended periods of time (like unbatching and spooling several megabytes of news
- one or two usually don't trigger it, larger batches do).
I wonder if it would be possible for the driver to monitor SMART and lighten the load on the drive when things don't seem normal.
What is normal, anyway? For example, my Seagate Barracuda IV shows continually increasing raw values for "Raw Read Error Rate", "Seek Error Rate" and "Hardware ECC Recovered". It works fine, though. The older U5 I still have running has a high but pretty constant raw value for the first, a slower rate of increase for the second and doesn't show the third.
I don't really believe the 310617 power on hours my Maxtor (the old 60 gig with 4 platters) claims, either.
Holger
Quoted 2 lines
I wonder if it would be possible for the driver to monitor SMART and lighten the load on the drive when things don't seem normal.
I think it would be fun to have SMART monitoring in the driver, but I'm not sure it's worth the bloat. It *can* be done in userspace, afterall.
Quoted 1 line
What is normal, anyway?
Not sure what 'normal' is, but the manufacturer defines thresholds, which are to be interpreted as 'drive is failing' if they are exceeded.
Quoted 2 lines
I don't really believe the 310617 power on hours my Maxtor (the old 60 gig with 4 platters) claims, either.
That's because it's reporting power on time in minutes :-)
John.
Am Fre, 2002-09-06 um 21.22 schrieb DevilKin:
Quoted 2 lines
Well, there were 21 ATA errors, and it showed 5 error blocks, with disk 'live' times of 629 hours.
No wonder it ran for 2 years. Are you using this machine frequently at all? :)
Quoted 1 line
The tests showed bad sectors, i'm currently running a disk erase.
This is exactly the mistake I've been meaning to warn you of. The disk will corrupt sooner or later again and you'll have to go through all the torture (possible backup/restore, missing data) again and if you're unlucky (which is quite possible with your frequency of use) the warranty is void until the problems appear the next time.
Signature · 2 lines
Servus,
DanielQuoted 7 lines
Quoted 1 line
The tests showed bad sectors, i'm currently running a disk erase.
This is exactly the mistake I've been meaning to warn you of. The disk will corrupt sooner or later again and you'll have to go through all the torture (possible backup/restore, missing data) again and if you're unlucky (which is quite possible with your frequency of use) the warranty is void until the problems appear the next time.
There are two separate issues here, though:
* Buggy firmware
* Unreliable media
We have confirmed, (I believe), that the drive did have the buggy firmware. We do not know yet whether the media is defective or not, but we do know that the drives are not the best in the world.
Alan also confirmed that the errors were direct from the device, and so it is not a kernel bug.
However, I raise the question of whether the new kernel version caused different access patterns to the device, and showed up the firmware bug that was there all the time. Or maybe the compilation of the new kernel thrashed the disk and showed up the firmware bug. If the machine has been on for some time, (months), doing not very much, maybe a lot of disk data was cached in RAM, and the kernel compile caused it to be re-read from disk, showing up media defects.
I was hoping that he would actually post the output of:
smartctl -a /dev/hda?
because that tells you all sorts of things, like, for example, reallocated sector count, and calibration retry count.
Obviously, it is not a good idea to use the drive for anything important until it has been tested in a non-critical application first.
Besides, you *do* backup, don't you? (Or do what Linus suggested a while ago, and upload your stuff to an ftp site that is mirrored worldwide.)
I don't see the point of returning a disk that turns out not to be faulty after the firmware upgrade, for replacement under the warranty, even if it qualifies for a warranty replacement, (which it shouldn't do), because you might be exchanging a good disk for a bad disk.
John.
Am Sam, 2002-09-07 um 15.08 schrieb [email protected]:
Quoted 1 line
Besides, you *do* backup, don't you?
I do but besides that there is still data loss involved and my time is expensive and limited, so I'd rather go for a hasslefree solution than to poke around in mud with a stick in the hope it might clear up.
Quoted 2 lines
(Or do what Linus suggested a while ago, and upload your stuff to an ftp site that is mirrored worldwide.)
Very practicable advise.
Quoted 2 lines
I don't see the point of returning a disk that turns out not to be faulty after the firmware upgrade,
The point is that until you know whether it really was the firmware, you've spend so much time that it is much easier to return the drive.
Quoted 1 line
even if it qualifies for a warranty replacement, (which it shouldn't do)
A faulty drive is a faulty drive and thus qualifies for a free replacement (at least in Germany). Nobody here can force you to try several costly things which might solve the problem; it is rather the manufacturers duty to fix it on their cost.
Quoted 1 line
because you might be exchanging a good disk for a bad disk.
Very doubtful considering past experience. Also it's not very probable (though it has happened) to receive a disk which is more broken than broken.
Signature · 2 lines
Servus,
DanielQuoted 5 lines
Quoted 1 line
Besides, you *do* backup, don't you?
I do but besides that there is still data loss involved and my time is expensive and limited, so I'd rather go for a hasslefree solution than to poke around in mud with a stick in the hope it might clear up.
Fair enough, if you don't have the time to devote to it, it's best to replace the drive.
I assumed from the size of this thread, which has nothing to do with the kernel anymore, that we were trying to find out what was to blame.
If this is going to become a flamewar, please remove the cc: to the kernel list, as I doubt that it interests them.
Quoted 4 lines
Quoted 2 lines
(Or do what Linus suggested a while ago, and upload your stuff to an ftp site that is mirrored worldwide.)
Very practicable advise.
Whatever - it was a joke.
The reason I brought up backups, was because even if you have a RAID array, of high quality drives, with non-sequential serial numbers, on hot-pluggable interfaces, with known good firmware, you can still get silent data corruption.
Fact - *NO* SLED, or RAID array, can ever be guaranteed never to silently flip a bit.
Quoted 5 lines
Quoted 2 lines
I don't see the point of returning a disk that turns out not to be faulty after the firmware upgrade,
The point is that until you know whether it really was the firmware, you've spend so much time that it is much easier to return the drive.
And the chances are you will get another drive of the same model, back from IBM. How does that help?
I already pointed out that there are two known issues here with these drive - firmware bugs, and media defects.
So far, all we can say is that the firmware problem is now fixed. On a replacement drive, you can't even say that.
The 'media errors' could have been caused entirely by the buggy firmware.
Quoted 6 lines
Quoted 1 line
even if it qualifies for a warranty replacement, (which it shouldn't do)
A faulty drive is a faulty drive and thus qualifies for a free replacement (at least in Germany). Nobody here can force you to try several costly things which might solve the problem; it is rather the manufacturers duty to fix it on their cost.
No, but you've upgraded the firmware, right? If that has fixed the problem, then it is not a faulty drive. If it is not a faulty drive, then what is the point in sending it back? If it is not a faulty drive, IBM would be justified in sending it right back to you at your expense. Oh, and it might get damaged in transit.
Quoted 5 lines
Quoted 1 line
because you might be exchanging a good disk for a bad disk.
Very doubtful considering past experience. Also it's not very probable (though it has happened) to receive a disk which is more broken than broken.=20
No, I would say it is very possible that you could receive a disk with the old firmware on it. So, you'll just plug in your 'new' disk, and in a few months, bad sectors will start appearing.
John.
Am Sam, 2002-09-07 um 17.02 schrieb [email protected]:
Quoted 1 line
No, but you've upgraded the firmware, right?
Not exactly. According to IBM technical support there is no such thing as a new firmware. The drives are alright, the OS is broken.
Quoted 1 line
If that has fixed the problem, then it is not a faulty drive.
Right, and how would you notice without sacrifying more data?
Quoted 2 lines
So, you'll just plug in your 'new' disk, and in a few months, bad sectors will start appearing.
Not if you sold it at Ebay, which is what I did with all *new* drives I received from IBM. I just kept the "serviceable used part" one in case I need to install Windows to upgrade the firmware of some drive or anything else in range.
Signature · 2 lines
Servus,
DanielThis discussion is becoming stupid, but here we go:
Quoted 3 lines
Quoted 1 line
No, but you've upgraded the firmware, right?
Not exactly.
??? Either you did or didn't.
Quoted 2 lines
According to IBM technical support there is no such thing as a new firmware. The drives are alright, the OS is broken.
Right, so you're calling Alan Cox a liar, then? I know who I believe.
Quoted 2 lines
Quoted 1 line
If that has fixed the problem, then it is not a faulty drive.
Right, and how would you notice without sacrifying more data?
smartctl -X /dev/hda?
'Execute Extended Self Test' might be a good start
or you could just copy data to/from it, generally hammer it and spin it up, down, and sideways, generally try to make it go wrong, and if your data is intact, then I would trust it more than a disk that arrived in a jiffy bag, with an assurance that 'this one works'.
Quoted 4 lines
Quoted 2 lines
So, you'll just plug in your 'new' disk, and in a few months, bad sectors will start appearing.
Not if you sold it at Ebay,
The bad sectors are just as likely to appear, but somebody else's data will be lost. Very nice gesture, not to mention that you probably violate the Ebay T&C by selling a product that you suspect is faulty.
Quoted 1 line
which is what I did with all *new* drives I received from IBM.
Well, I won't buy a second hand drive from you then :-).
Quoted 2 lines
I just kept the "serviceable used part" one in case I need to install Windows to upgrade the firmware of some drive or anything else in range.
Fine, if that's what floats your boat.
Infact, I was completely wrong, OK? You were right all along, so there is no need to continue this pointless thread.
John.
Quoted 4 lines · On Sat, 2002-09-07 at 21:41, [email protected] wrote:
Quoted 2 lines
According to IBM technical support there is no such thing as a new firmware. The drives are alright, the OS is broken.
Right, so you're calling Alan Cox a liar, then? I know who I believe.
Hardly. He said IBM tech support told him one thing, and they told me another. Give it a rest
Quoted 6 lines · Daniel Egger
Am Sam, 2002-09-07 um 17.02 schrieb [email protected]:
Quoted 1 line
No, but you've upgraded the firmware, right?
Not exactly. According to IBM technical support there is no such thing as a new firmware. The drives are alright, the OS is broken.
The IBM technical support I dealt with not only confirmed there was new firmware, the tools updated it and said they had 8)
Quoted 10 lines · Daniel Egger
Quoted 6 lines
Am Sam, 2002-09-07 um 17.02 schrieb [email protected]:
Quoted 1 line
No, but you've upgraded the firmware, right?
Not exactly. According to IBM technical support there is no such thing as a new firmware. The drives are alright, the OS is broken.
The IBM technical support I dealt with not only confirmed there was new firmware, the tools updated it and said they had 8)
Here is the URL:
http://www-1.ibm.com/support/docview.wss?uid=psg1MIGR-39082
it expressly states that the firmware is intended for the DTLA-307060.
The page mentions that is it enhances stability and SMART data collection.
John.
On Sat, 7 Sep 2002 [email protected] wrote:
...
Quoted 5 lines
Here is the URL:
http://www-1.ibm.com/support/docview.wss?uid=psg1MIGR-39082
it expressly states that the firmware is intended for the DTLA-307060.
The firmware update is for many more drives than that, My own
Model=IBM-DTLA-305040, FwRev=TW4OA60A
is also recommended, as well as many with a FwRev=xxxOyzzz with zzz<66A. Now i have to find a windows machine to try it out on...
Dave,
Signature · 2 lines
Dave Forrest [email protected] (804)642-0662h (434)924-3954w http://mug.sys.virginia.edu/~drf5n/
Quoted 7 lines · David Forrest
On Sat, 7 Sep 2002 [email protected] wrote:
...
Quoted 4 lines
Here is the URL:
Quoted 8 lines
Quoted 1 line
it expressly states that the firmware is intended for the DTLA-307060.
The firmware update is for many more drives than that, My own
Model=IBM-DTLA-305040, FwRev=TW4OA60Ais also recommended, as well as many with a FwRev=xxxOyzzz with zzz<66A. Now i have to find a windows machine to try it out on...
You don't need to. All you need is someone run this tool and send you the image it creates. I put mine as boot.img on a CD so I can upgrade all the disks I have in boxes without floppy disk drives. It's a self booting DOS disk.
Regards
Henning
Signature · 5 lines
Dipl.-Inf. (Univ.) Henning P. Schmiedehausen -- Geschaeftsfuehrer INTERMETA - Gesellschaft fuer Mehrwertdienste mbH [email protected] Am Schwabachgrund 22 Fon.: 09131 / 50654-0 [email protected] D-91054 Buckenhof Fax.: 09131 / 50654-20
Quoted 11 lines
Quoted 6 lines
The firmware update is for many more drives than that, My own
Model=IBM-DTLA-305040, FwRev=TW4OA60Ais also recommended, as well as many with a FwRev=xxxOyzzz with zzz<66A. Now i have to find a windows machine to try it out on...
You don't need to. All you need is someone run this tool and send you the image it creates. I put mine as boot.img on a CD so I can upgrade all the disks I have in boxes without floppy disk drives. It's a self booting DOS disk.
As the old firmware is known to be buggy, and those bugs are relevant when using Linux, and updated firmware is available, is it worth checking for the known buggy firmware version in the ide driver?
I realise that we cannot check every drive in the world for compatibility, but if this is a known issue...
John.
If I knew how to check that I would. We wanted to do the same for the ancient WD but there was no way to tell
Quoted 6 lines · Daniel Egger
Am Sam, 2002-09-07 um 17.02 schrieb [email protected]:
Quoted 1 line
No, but you've upgraded the firmware, right?
Not exactly. According to IBM technical support there is no such thing as a new firmware. The drives are alright, the OS is broken.
They are full of CRAP!
IBM ran TASKFILE IO throught there bus analyzers and it came up clean. IBM also introduced FLAGGED versions of the diagnostic TASKFILE transport for eventual use of their DFT (Drive Fitness Test).
You tell the service tech he is smoking crack.
The kernel passed with flying colors in their disk labs. If you read in ide-taskfile.c version 0.33 and above, you will see they did some work on the driver and verified issues.
Now earlier I published a method of how to stablize the drive once you back up all the data you can off of it. Since I do not yet have a source verison of DFT-Linux, or binary yet, I can not offer much more native.
Cheers,
Andre Hedrick
LAD Storage Consulting Group
Send me the results offline
Quoted 21 lines · DevilKin
Quoted 11 lines · On Friday 06 September 2002 17:36, [email protected] wrote:
Quoted 8 lines
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Have a look at:
Quoted 8 lines
http://csl.cse.ucsc.edu/smart.shtml
there you will find software for interrogating and monitoring the S.M.A.R.T. data available from your drive. It's a little late to start monitoring it, if the drive is already dying, but if, for example, it shows a lot of re-allocated sectors, or spin retries, you'll know something is wrong.
Quoted 18 lines
OK, I downloaded that and installed it, but well, frankly, it shows me very little useful stuff.
Or i'm just not good at interpreting this.
DK
Signature · 9 lines
"I gained nothing at all from Supreme Enlightenment, and for that very reason it is called Supreme Enlightenment." -- Gotama Buddha - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Andre Hedrick
LAD Storage Consulting Group
same problem I was having with 2.4.20-pre4-ac2-preempt.
alan didn't want to hear it from me due to the -preempt
my system was e7500 chipset, dual xeon, WD 40g drive, ext2 or ext3.
from this we can glean: preempt not a factor, HD manufacturer not a factor, FS not a factor. don't know what chipset you are using.
I was allso geting badCRC errors.
Quoted 34 lines · DevilKin
Hello kernel people,
Kernel running: 2.4.20-pre1ac3 or -pre5ac2 (same under both)
Today I discovered a stale copy of qt-3.0.3 lying about on my disk. When I tried to delete it, this started showing up in my log files:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126720x0SD]
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126770x0SD]and rm just reported me 'Permission denied'.
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Thanks!
DK
Signature · 8 lines
/************************************************** ** Mark Salisbury || [email protected] ** ** If you would like to sponsor me for the ** ** Mass Getaway, a 150 mile bicycle ride to for ** ** MS, contact me to donate by cash or check or ** ** click the link below to donate by credit card ** **************************************************/ https://www.nationalmssociety.org/pledge/pledge.asp?participantid=86736
Quoted 1 line · mbs
same problem I was having with 2.4.20-pre4-ac2-preempt.
I beg to differ. He has a dying disk, you have some weird crc and other goings on
Quoted 3 lines · DevilKin
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472
That certainly looks like a drive error.
Quoted 2 lines
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Get the IBM disk tools, upgrade the firmware and see what the ibm tools have to say. IBM drives have had some problems with spontaneous bad blocks appearing that go away with new firmware and a run of the disk tools. More importantly if thats the problem with the firmware update they dont come back until the drive really dies.
Am Fre, 2002-09-06 um 17.38 schrieb Alan Cox:
Quoted 4 lines
Get the IBM disk tools, upgrade the firmware and see what the ibm tools have to say. IBM drives have had some problems with spontaneous bad blocks appearing that go away with new firmware and a run of the disk tools.
The "run of the disk tools" that does away with the badblocks is a lowlevel format; a tedious way to spent ones' time on a harddrive that will die anyway soon.
Quoted 2 lines
More importantly if thats the problem with the firmware update they dont come back until the drive really dies.
Right, which is probably shortly after. Especially on a two years old drive I wouldn't go through all the troubles to backup 60GB data, lowlevel format the drive, restore the data and hope the problems are gone; instead I'd rather get a new drive within the warranty and cross fingers.
BTW: I did the backup way exactly once and the drive got back to me with new errors two weeks after.
Signature · 2 lines
Servus,
DanielQuoted 10 lines · Daniel Egger
Am Fre, 2002-09-06 um 17.38 schrieb Alan Cox:
Quoted 4 lines
Get the IBM disk tools, upgrade the firmware and see what the ibm tools have to say. IBM drives have had some problems with spontaneous bad blocks appearing that go away with new firmware and a run of the disk tools.
The "run of the disk tools" that does away with the badblocks is a lowlevel format; a tedious way to spent ones' time on a harddrive that will die anyway soon.
For the IBM's it depends what the problem is. Spontaneous bad blocks appearing during power off appears to be fixed by the firmware update
forgot to say: my drive worked fine with 2.4.19-pre3-ac5-preempt before the move to the -20 kernel.
also worked fine after a fdisk/reinstall and continued to work fine till the first time I booted on a (freshly built) -20-ac version.
I thought it was the drive so I replaced it with a brand new drive, and had _EXACTLY_ the same failure pattern.
------
same problem I was having with 2.4.20-pre4-ac2-preempt.
alan didn't want to hear it from me due to the -preempt
my system was e7500 chipset, dual xeon, WD 40g drive, ext2 or ext3.
from this we can glean: preempt not a factor, HD manufacturer not a factor, FS not a factor. don't know what chipset you are using.
I was allso geting badCRC errors.
Quoted 34 lines · DevilKin
Hello kernel people,
Kernel running: 2.4.20-pre1ac3 or -pre5ac2 (same under both)
Today I discovered a stale copy of qt-3.0.3 lying about on my disk. When I tried to delete it, this started showing up in my log files:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126720x0SD]
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126770x0SD]and rm just reported me 'Permission denied'.
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Thanks!
DK
Signature · 8 lines
/************************************************** ** Mark Salisbury || [email protected] ** ** If you would like to sponsor me for the ** ** Mass Getaway, a 150 mile bicycle ride to for ** ** MS, contact me to donate by cash or check or ** ** click the link below to donate by credit card ** **************************************************/ https://www.nationalmssociety.org/pledge/pledge.asp?participantid=86736
fdisk/format and reinstall but stick with a 2.4.19 or 2.4.19-ac kernel.
I would bet money that the problem is purely a .20-preX-acX thing.
run it a while on 2.4.19 to verify that life is good. then build a new 2.4.20-pre1-ac3 and boot it. I bet that within minutes of normal use, you will have a problem.
(I have done this loop 3 times.)
Quoted 34 lines · DevilKin
Hello kernel people,
Kernel running: 2.4.20-pre1ac3 or -pre5ac2 (same under both)
Today I discovered a stale copy of qt-3.0.3 lying about on my disk. When I tried to delete it, this started showing up in my log files:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126720x0SD]
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126770x0SD]and rm just reported me 'Permission denied'.
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Thanks!
DK
Signature · 8 lines
/************************************************** ** Mark Salisbury || [email protected] ** ** If you would like to sponsor me for the ** ** Mass Getaway, a 150 mile bicycle ride to for ** ** MS, contact me to donate by cash or check or ** ** click the link below to donate by credit card ** **************************************************/ https://www.nationalmssociety.org/pledge/pledge.asp?participantid=86736
Quoted 3 lines · mbs
fdisk/format and reinstall but stick with a 2.4.19 or 2.4.19-ac kernel.
I would bet money that the problem is purely a .20-preX-acX thing.
Its a status entry direct from the drive. The drive says "uncorrectable error" which means there is a media problem. Its nothing to do with Linux
Am Fre, 2002-09-06 um 22.32 schrieb Alan Cox:
Quoted 3 lines
Its a status entry direct from the drive. The drive says "uncorrectable error" which means there is a media problem. Its nothing to do with Linux
According to IBM tech staff it is an OS problem because the data transfer to the drive got corrupted somehow and thus the drive forgot about the sectors.
I was just laughing my ass off when I heard this, especially after the 4th drive failing within a short period of time with the same guy calling me on my cell phone and telling me the same shite over and over again...
Signature · 2 lines
Servus,
DanielFirst BACK up what is left.
Next dig out smartsuite from http://www.linux-ide.org/smart.html
Run it in full capture mode, please use another disk to run root, or the system will tank.
Read and save smart logs.
cat /dev/zero > /dev/hd{IBM-DTLA-307060}x
Rerun Smart in full capture mode.
Reread smart logs and compare.
cat /dev/urandom > /dev/hd{IBM-DTLA-307060}x
If you get no errors you can reuse the drive, for how long? Maybe 6 months to a year.
Now, I can not tell you what, why, how things are going on. Sheesh, I expect to be in a deep six for this series of events already.
Sorry, I can not say anymore.
If you do not like the above, you need to run out and buy another drive fast.
Cheers,
Quoted 26 lines · DevilKin
Hello kernel people,
Kernel running: 2.4.20-pre1ac3 or -pre5ac2 (same under both)
Today I discovered a stale copy of qt-3.0.3 lying about on my disk. When I tried to delete it, this started showing up in my log files:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126720x0SD]
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: error=0x40 { UncorrectableError }, LBAsect=7072862, sector=1803472end_request: I/O error, dev 03:06 (hda), sector 1803472
vs-13070:reiserfs_read_inode2: i/o failure occurred trying to find stat data of [612671 6126770x0SD]and rm just reported me 'Permission denied'.
I've looked up these errors on the net, and as far as i can tell it means that the drive has some bad sectors at the given addresses and that it will probably die on me sooner or later.
Quoted 19 lines
Can someone either confirm this to me or tell me what to do to fix it?
The drive involved is an IBM-DTLA-307060, which has served me without problems now for about 2 years.
Thanks!
DK
Signature · 9 lines
If all the Chinese simultaneously jumped into the Pacific off a 10 foot platform erected 10 feet off their coast, it would cause a tidal wave that would destroy everything in this country west of Nebraska. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Andre Hedrick
LAD Storage Consulting Group
Quoted 1 line
Next dig out smartsuite from http://www.linux-ide.org/smart.html
I thought that smartsuite was now unmaintained, and posted a comment to that effect earlier in this thread - sorry for the mis-information.
John.
Technically it is, I am working to transfer the copyright/license to LAD. Then I can update it and transform it to the preferred kernel API that is not enabled by default. I expect it will require an sub-set of the taskfile_ioctl calls to restrict various IO calls.
Cheers,
Quoted 6 lines · On Sat, 7 Sep 2002 [email protected] wrote:
Quoted 1 line
Next dig out smartsuite from http://www.linux-ide.org/smart.html
I thought that smartsuite was now unmaintained, and posted a comment to that effect earlier in this thread - sorry for the mis-information.
John.
Andre Hedrick
LAD Storage Consulting Group