Skip to contentSkip to conversation

Hao much tape have I used?

DISCUSSION Paul Furness 4 participants 4 messages Sep 8, 2002 – Sep 9, 2002

lore
Share & tools
lore
#0 lore raw

Can anyone tell me how to find out how full a tape is? Specifically, DLT and LTO tapes which are in a robot. I have no problem loading the tapes into the drive (using MTX) and mt works just fine - but after putting a load of dumps on the tape, I need to know it the tape is actually full or not. And of course, the tape drive uses hardware compression, so I can't just add up the data dumped and subtract it from the capacity of the tape because the compression is variable.

Any ideas / experiences with this would be appreciated.

P.

Signature · 5 lines
Paul Furness

Systems Manager

2+2=5 for extremely large values of 2.
#1 lore raw

Hi

I am using tar to take backup on to the tape. I want to know whether I have to enable the "compression" manually in tar or it is done by the hardware itself.

Signature · 11 lines
**************************************************************************

Mohammed Khalid Ansari                    Tel (res) : 0091-022-3051360
Assistant Manager II                          (off) : 0091-022-2024641
National Centre for Software Technology   Fax       : 0091-022-2049573 
8th flr,Air India Build. Nariman Point,   E-Mail    : [email protected] 	
Mumbai 400021.

Homepage : http://soochak.ncst.ernet.in/~khalid			  	  

**************************************************************************
Quoted 15 lines · Paul Furness

Can anyone tell me how to find out how full a tape is? Specifically, DLT and LTO tapes which are in a robot. I have no problem loading the tapes into the drive (using MTX) and mt works just fine - but after putting a load of dumps on the tape, I need to know it the tape is actually full or not. And of course, the tape drive uses hardware compression, so I can't just add up the data dumped and subtract it from the capacity of the tape because the compression is variable.

Any ideas / experiences with this would be appreciated.

P.

#2 lore raw
Quoted 3 lines · Mohammed Khalid Ansari

I am using tar to take backup on to the tape. I want to know whether I have to enable the "compression" manually in tar or it is done by the hardware itself.

It depends upon whether you're referring to "hardware" compression (which is performed by the tape drive), or "software" compression (i.e. feeding the output from "tar" through "gzip" etc).

For hardware compression, you normally control whether compression is performed by using the "mt" command prior to writing to the tape.

Software compression is performed either by using the appropriate "tar" switches (e.g. "-z", "-Z", "--use-compress-program" etc), or by manually piping the output from "tar" through the compression program before writing it to the tape drive.

Using software compression for backups is generally considered a bad idea, as a single error may render a substantial proportion of the backup unusable. Hardware compression tends to have better recoverability (but a lower overall compression ratio).

Signature · 1 line
Glynn Clements <[email protected]>
#3 lore raw
In reply to Paul Furness

mt tell, tell you in which block of the tape are you located, so if you know how much blocks you tape has you can see how much tape is left.

Quoted 11 lines · Paul Furness

Can anyone tell me how to find out how full a tape is? Specifically, DLT and LTO tapes which are in a robot. I have no problem loading the tapes into the drive (using MTX) and mt works just fine - but after putting a load of dumps on the tape, I need to know it the tape is actually full or not. And of course, the tape drive uses hardware compression, so I can't just add up the data dumped and subtract it from the capacity of the tape because the compression is variable.

Any ideas / experiences with this would be appreciated.

P.

Signature · 1 line
Luis Valencia