Modem communication, HP 730
Dear All,
I hope that I am sending this to an appropriate list. To be honest I am running out of ideas.
I recently received a HP 730 which I am attempting to restore. I am trying to install an external modem (V90 Velo Net ME220). However, it is acting strangley. It works fine (using minicom) at connection speeds of up to 19200, after that the modem fails to respond to AT commands altogether.
I have read through both the serial and modem how-tos in detail and tried what I could think of. Including using a large range of different settings for setserial and stty. Does anyone have any idea what I might be doing wrong? One interesting point to note, I have no monitor or HIL keyboard and have been using the first serial port
(A) for a console.
Any advice would be greatly received,
Jon Sharp
__
'The art of good lecturing is to transfer the information from my notes to your notes without it passing through eithers brain.' Cambridge University Lecturer
_________________________________________________________________
http://fastmail.ca/ - Fast Secure Web Email for Canadians
Quoted 3 lines · Jon Sharp
It works fine (using minicom) at connection
speeds of up to 19200, after that the modem fails to respond to AT commands altogether.
Does anyone know at which speeds HW handshaking is necessary? 730 is a pretty old machine.
grant
I know the internal modem of the K-class is limited to 19200. All of the support modems we install for the systems are slowed down to 19200 even though they are 56k. Coincidence?
derek
Quoted 5 lines · --- Grant Grundler
Quoted 3 lines · Jon Sharp
It works fine (using minicom) at connection
speeds of up to 19200, after that the modem fails to respond to AT commands altogether.
Quoted 8 lines
Does anyone know at which speeds HW handshaking is necessary? 730 is a pretty old machine.
grant
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
Quoted 3 lines · Derek Engelhaupt
I know the internal modem of the K-class is limited to 19200. All of the support modems we install for the systems are slowed down to 19200 even though they are 56k. Coincidence?
Maybe not. Does the modem connect directly the console manager or whatever it's called? That might be the limiting factor.
Could I cut off the goofy connector for K-class modem, solder on a DB-9 (or DB25) and have a cool external 56k Modem?
If so, I only need to know what the pinout is since power probably comes through the cable as well.
I've seen so many of those go in the trash here.
grant
Grant,
That thing you speak of is not the modem...the modem is inside the K. That thing is called a LAM. Local Access Module. It varied from country to country so they don't have to change the modem only the LAM.
The modem acctually plugs into the Core i/o board via a set of about
20 pins that actually come throught the modem board. Very easy to bend and get out of alignment.
derek
Quoted 16 lines · --- Grant Grundler
Quoted 1 line · Derek Engelhaupt
I know the internal modem of the K-class is limited to 19200. All
of
Quoted 1 line
the support modems we install for the systems are slowed down to
19200
Quoted 1 line
even though they are 56k. Coincidence?
Maybe not. Does the modem connect directly the console manager or whatever it's called? That might be the limiting factor.
Could I cut off the goofy connector for K-class modem, solder on a DB-9
(or DB25) and have a cool external 56k Modem?
If so, I only need to know what the pinout is since power probably comes through the cable as well.
Quoted 3 lines
I've seen so many of those go in the trash here.
grant
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
[parisc-linux] E55
In reply to Grant GrundlerI was just curious how far in the boot process you E55 guys get. I just tried to load the one I have in the office tonight. I retrofitted it with an A1703-60003 LAN/Console/SCSI card I pulled out of one of our "crash and burn" H70 boxes. It gets past the "console" message about "if this is the last thing you see" then starts dumping the stacks and ends in a Kernal error 15. This card doesn't use the mux port to connect the console it uses a PS/2 type connector to the card and a DB25 connector to the terminal. Just wanted to see how this compares to the other E Series machines out there.
derek
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
Re: [parisc-linux] E55
I have been playing with an E35 and I can get the boot to go farther then that. Right now the boot is failing somewhere between the LED detection and the POSIX conformance testing by UNIFIX. I do not really care about this failure right now since I am really only interested in the discovering the missing devices on these systems.
Tonight, I found the missing devices on the system and I am currently working on figuring out how to integrate this discovery into the bus walk code. I hope to have a patch committed within the next day or so which detects all the devices on the system. After that I will add this failure to my TODO list (if the ESIEE will still let me have access to this system, but i am hoping that someone else will take the challenge and find/fix the problem :))
Thanks,
- Ryan
Quoted 21 lines · Derek Engelhaupt
I was just curious how far in the boot process you E55 guys get. I just tried to load the one I have in the office tonight. I retrofitted it with an A1703-60003 LAN/Console/SCSI card I pulled out of one of our "crash and burn" H70 boxes. It gets past the "console" message about "if this is the last thing you see" then starts dumping the stacks and ends in a Kernal error 15. This card doesn't use the mux port to connect the console it uses a PS/2 type connector to the card and a DB25 connector to the terminal. Just wanted to see how this compares to the other E Series machines out there.
derek
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Re: [parisc-linux] E55
In reply to Derek EngelhauptI have the E55 as it is, without any additional card, and with my PDC Console driver I can completely boot the system and work on it. BUT: Only via NFS Root, as there is currently no SCSI support, no support for the MUX (except port 0 as console with the PDC driver) and without parallel (printer) port.
But Linux runs completely, including login, remote X usage (xterm, etc...), access to the internet via LAN, etc, ....
Hi Ryan, you have found the device ? This one on the BC ? Sounds gooooooood !
Christoph
Quoted 21 lines · Derek Engelhaupt
I was just curious how far in the boot process you E55 guys get. I just tried to load the one I have in the office tonight. I retrofitted it with an A1703-60003 LAN/Console/SCSI card I pulled out of one of our "crash and burn" H70 boxes. It gets past the "console" message about "if this is the last thing you see" then starts dumping the stacks and ends in a Kernal error 15. This card doesn't use the mux port to connect the console it uses a PS/2 type connector to the card and a DB25 connector to the terminal. Just wanted to see how this compares to the other E Series machines out there.
derek
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Signature · 3 lines
------------------------------------------------------- private: [email protected] company: [email protected]