Unlocking flash problem with the epxa10db device
A message that is not in the archive (sent off-list or not yet received): [email protected]
I wrote cfi_intelext_varsize_frob(). It is behaving as intended.
You have to unlock/lock/erase/etc. an *entire* block/sector at a time.
There's no way to unlock 4 bytes and leave the other (erasesize - 4) bytes locked. So the function returns EINVAL if the size isn't an even "multiple" of the block size(s). ("Multiple" here is not meant strictly in the mathematical sense; consider variably-sized blocks.)
You'll find the other functions behave identically, e.g. erase.
-ch
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Louie Boczek
Sent: Thursday, September 19, 2002 8:11 PM
To: ARM Linux kernel Mailinglist
Subject: Unlocking flash problem with the epxa10db device
I just started working with the Altera Excalibur board and ran into the following problem.
I was not able to write to the flash and found the problem lied in the unlocking code.
In the epxa10db-flash.c:epxa10db_mtd_init() routine it calls:
mymtd->unlock(mymtd, mymtd->eraseregions[i].offset + j *
mymtd->eraseregions[i].erasesize, 4);
which eventually calls "cfi_cmdsetc_001.c:cfi_intelext_varsize_frob()" in this routine there is a check to make sure that the region being unlocked is the whole region with the check:
if ((ofs + len) & (regions[i].erasesize -1))
return -EINVAL;this fails since the call was only to unlock 4 bytes not erasesize. So I fixed the problem by changing the call to mymtd->unlock() to pass the
erasesize instead of 4.
But the question is, should "cfi_intelext_varsize_frob()" check to see if the whole region is specifed or should it unlock the region that the specified location is located. I think the later.
I am using the linux-2.4.18-rmk7 but I also checked linux-2.4.19 and the
problem is also there.
I am new to this, I hope I gave enough and thorough informartion.
thanks
louie
-------------------------------------------------------------------
Subscription options:
http://lists.arm.linux.org.uk/mailman/listinfo/linux-arm-kernel
FAQ/Etiquette:
http://www.arm.linux.org.uk/armlinux/mailinglists.php
Sounds good to me. I could have gone either way. So I actually fixed it the way you want.
On a side note, is there any reason that the entire flash is unlocked on boot instead of just the filesystem. I am referencing the unlock code in epxa10db-flash.c.
thanks
louie
Quoted 60 lines · Christopher Hoover
I wrote
cfi_intelext_varsize_frob(). It is behaving as intended.You have to unlock/lock/erase/etc. an *entire* block/sector at a time.
There's no way to unlock 4 bytes and leave the other (erasesize - 4) bytes locked. So the function returns EINVAL if the size isn't an even "multiple" of the block size(s). ("Multiple" here is not meant strictly in the mathematical sense; consider variably-sized blocks.)
You'll find the other functions behave identically, e.g. erase.
-ch
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Louie Boczek
Sent: Thursday, September 19, 2002 8:11 PM
To: ARM Linux kernel Mailinglist
Subject: Unlocking flash problem with the epxa10db deviceI just started working with the Altera Excalibur board and ran into the following problem.
I was not able to write to the flash and found the problem lied in the unlocking code. In the epxa10db-flash.c:epxa10db_mtd_init() routine it calls:
mymtd->unlock(mymtd, mymtd->eraseregions[i].offset + j *mymtd->eraseregions[i].erasesize, 4);
which eventually calls "cfi_cmdsetc_001.c:cfi_intelext_varsize_frob()" in this routine there is a check to make sure that the region being unlocked is the whole region with the check:
if ((ofs + len) & (regions[i].erasesize -1)) return -EINVAL;this fails since the call was only to unlock 4 bytes not erasesize. So I fixed the problem by changing the call to
mymtd->unlock()to pass theerasesize instead of 4.
But the question is, should "
cfi_intelext_varsize_frob()" check to see if the whole region is specifed or should it unlock the region that the specified location is located. I think the later.I am using the linux-2.4.18-rmk7 but I also checked linux-2.4.19 and the
problem is also there.
I am new to this, I hope I gave enough and thorough informartion.
thanks
louie-------------------------------------------------------------------
Subscription options:
http://lists.arm.linux.org.uk/mailman/listinfo/linux-arm-kernel
FAQ/Etiquette:
http://www.arm.linux.org.uk/armlinux/mailinglists.php
Quoted 4 lines
On a side note, is there any reason that the entire flash is unlocked on boot instead of just the filesystem. I am referencing the unlock code in
epxa10db-flash.c.
Not really, I didn't feel that the flash locking added much so I just unlocked the whole flash at boot time and forgot about it.
Clive