VIA VT8235 (ALC201) problems
I'm forwarding this to -devel, just in case you guys know something that the folks on -user don't.
I guess I should mention that I sometimes get this error message while attempting to play sound (not always, though):
ALSA lib pcm_hw.c:398:(snd_pcm_hw_prepare) SNDRV_PCM_IOCTL_PREPARE failed:
Device or resource busy
Some times I get that error, although the sound continues to play. FWIW, I use Linux 2.4.19 with a huge patchset (sys-kernel/lolo-sources i Gentoo/Portage).
This might be very irrelevant and uninteresting, but I tried getting it to work again just now, and this quote is a bit incorrect:
Quoted 2 lines
It tends to play sounds very, very slowly, and 1/10 second samples over and over again (perhaps 20 times).
It's more like 0.5 second samples that are played five times. :P
Best Regards,
---------- Forwarded Message ----------
Subject: [Alsa-user] VIA VT8235 (ALC201) problems
Date: Wednesday 16 October 2002 15:49
From: Joachim Blaabjerg <[email protected]>
To: [email protected]
Hi,
I recently bought an EPoX 8K5A2 motherboard, with an onboard ALC201 sound chip. This motherboard utilizes VIA's new VT8235 south bridge (as opposed to VT8233 in most other recent VIA chipset boards), which I think may be the cause of my sound problems. I've tried various ALSA drivers with little or no success; neither of via82cxxx_audio, snd-via686a or snd-intel8x0 will load (init_module: No such device).
There is however one driver that does load: snd-via8233. Sadly, this driver fails to produce anything but noise. It tends to play sounds very, very slowly, and 1/10 second samples over and over again (perhaps 20 times).
I've looked at the RealTek site, and they offer driver downloads. This is
just a repackaging of alsa-driver-0.9.0_rc3 (which I am using), and a prewritten modules.conf that utilises the snd-via8233 module.
Has anyone had any luck with this sound chip/motherboard?
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
_______________________________________________
Alsa-user mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-user
-------------------------------------------------------
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
Hi,
please try the cvs version.
the via8233 (and via686) driver has been changed much on cvs since 0.9.0rc3. now they are merged as a unifed module "snd-via82xx".
Takashi
At Wed, 16 Oct 2002 16:28:19 +0200,
Quoted 66 lines · Joachim Blaabjerg
I'm forwarding this to -devel, just in case you guys know something that the folks on -user don't.
I guess I should mention that I sometimes get this error message while attempting to play sound (not always, though):
ALSA lib pcm_hw.c:398:(snd_pcm_hw_prepare)
SNDRV_PCM_IOCTL_PREPAREfailed:
Device or resource busySome times I get that error, although the sound continues to play. FWIW, I use Linux 2.4.19 with a huge patchset (sys-kernel/lolo-sources i Gentoo/Portage).
This might be very irrelevant and uninteresting, but I tried getting it to work again just now, and this quote is a bit incorrect:
Quoted 2 lines
It tends to play sounds very, very slowly, and 1/10 second samples over and over again (perhaps 20 times).
It's more like 0.5 second samples that are played five times. :P
Best Regards,
---------- Forwarded Message ----------
Subject: [Alsa-user] VIA VT8235 (ALC201) problems
Date: Wednesday 16 October 2002 15:49
From: Joachim Blaabjerg <[email protected]>
To: [email protected]Hi,
I recently bought an EPoX 8K5A2 motherboard, with an onboard ALC201 sound chip. This motherboard utilizes VIA's new VT8235 south bridge (as opposed to VT8233 in most other recent VIA chipset boards), which I think may be the cause of my sound problems. I've tried various ALSA drivers with little or no success; neither of
via82cxxx_audio, snd-via686a or snd-intel8x0 will load (init_module: No such device).There is however one driver that does load: snd-via8233. Sadly, this driver fails to produce anything but noise. It tends to play sounds very, very slowly, and 1/10 second samples over and over again (perhaps 20 times).
I've looked at the RealTek site, and they offer driver downloads. This is
just a repackaging of alsa-driver-0.9.0_rc3 (which I am using), and a prewritten modules.conf that utilises the snd-via8233 module.Has anyone had any luck with this sound chip/motherboard?
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
_______________________________________________
Alsa-user mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-user-------------------------------------------------------
Quoted 10 lines
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
_______________________________________________
Alsa-devel mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
Quoted 5 lines · Takashi Iwai
Hi,
please try the cvs version.
the via8233 (and via686) driver has been changed much on cvs since 0.9.0rc3. now they are merged as a unifed module "snd-via82xx".
Thanks for the tip. Didn't make a difference, though. Alsa-mixer now sees the card as "VIA 8233A/C" as opposed to "VIA 8233", but it's still not "VIA 8235". Looking at the comment at the top of the file, it seems to be supported, but looking at the code, I see this:
switch (chip_type) {
case TYPE_VIA686:
strcpy(card->driver, "VIA686A");
strcpy(card->shortname, "VIA 82C686A/B");
break;
case TYPE_VIA8233:
strcpy(card->driver, "VIA8233");
strcpy(card->shortname, "VIA 8233A/C");
break;
default:[...]
And this:
static struct pci_device_id snd_via82xx_ids[] __devinitdata = {
{ 0x1106, 0x3058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, TYPE_VIA686, }, /* 686A */
{ 0x1106, 0x3059, PCI_ANY_ID, PCI_ANY_ID, 0, 0, TYPE_VIA8233, }, /*
VT8233 */
{ 0, }
};It doesn't look to me like the 8235 chip is supported..?
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
At Wed, 16 Oct 2002 18:03:48 +0200,
Quoted 4 lines · Joachim Blaabjerg
Quoted 2 lines · Takashi Iwai
Hi,
Quoted 8 lines
Quoted 3 lines
please try the cvs version.
the via8233 (and via686) driver has been changed much on cvs since 0.9.0rc3. now they are merged as a unifed module "snd-via82xx".Thanks for the tip. Didn't make a difference, though. Alsa-mixer now sees the card as "VIA 8233A/C" as opposed to "VIA 8233", but it's still not "VIA 8235". Looking at the comment at the top of the file, it seems to be supported, but looking at the code, I see this:
8235 has the same pci id with 8233, so it's ok.
Takashi
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
Quoted 4 lines · you
8235 has the same pci id with 8233, so it's ok.
Takashi
As far as I know, though, the 8235 south bridge uses a different sound chip. VT8233 uses ALC650, while VT8235 uses ALC201. Or am I wrong?
And no, I still can't get sound. :)
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
At Wed, 16 Oct 2002 18:26:12 +0200,
Quoted 10 lines · Joachim Blaabjerg
Quoted 4 lines · you
8235 has the same pci id with 8233, so it's ok.
Takashi
As far as I know, though, the 8235 south bridge uses a different sound chip. VT8233 uses ALC650, while VT8235 uses ALC201. Or am I wrong?
yes, you are confused among two things.
ALC650 and ALC201 are AC97 codecs, which corresponds to ADC/DAC and mixer parts. it has nothing to do with the sound engine. the sound core of VT8235 is almost identical with 8233, thus via82xx driver is the one you need.
Quoted 1 line
And no, I still can't get sound. :)
please elaborate the phenomenon __on the latest driver__.
* totally silent --> check the mixer configuration?
* playback produces repeated sounds --> irq problem?
* playback rate doesn't match --> adjustment via snd_ac97_clock option?
Takashi
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
Quoted 12 lines · Takashi Iwai
At Wed, 16 Oct 2002 18:26:12 +0200,
Quoted 8 lines · Joachim Blaabjerg
Quoted 4 lines · you
8235 has the same pci id with 8233, so it's ok.
Takashi
As far as I know, though, the 8235 south bridge uses a different sound chip. VT8233 uses ALC650, while VT8235 uses ALC201. Or am I wrong?
Quoted 6 lines
yes, you are confused among two things.
ALC650 and ALC201 are AC97 codecs, which corresponds to ADC/DAC and mixer parts. it has nothing to do with the sound engine. the sound core of VT8235 is almost identical with 8233, thus via82xx driver is the one you need.
Ah, I see. I guess this is an alsa-user issue, then. Sorry :)
Quoted 7 lines
Quoted 1 line
And no, I still can't get sound. :)
please elaborate the phenomenon
__onthe latestdriver__.* totally silent --> check the mixer configuration?
* playback produces repeated sounds --> irq problem?
That might be it. Thanks for the assistance!
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by: viaVerio will pay you up to $1,000 for every account that you consolidate with us.
http://ad.doubleclick.net/clk;4749864;7604308;v?
http://www.viaverio.com/consolidator/osdn.cfm
Quoted 12 lines · Takashi Iwai
At Wed, 16 Oct 2002 18:26:12 +0200,
Quoted 8 lines · Joachim Blaabjerg
Quoted 4 lines · you
8235 has the same pci id with 8233, so it's ok.
Takashi
As far as I know, though, the 8235 south bridge uses a different sound chip. VT8233 uses ALC650, while VT8235 uses ALC201. Or am I wrong?
Quoted 6 lines
yes, you are confused among two things.
ALC650 and ALC201 are AC97 codecs, which corresponds to ADC/DAC and mixer parts. it has nothing to do with the sound engine. the sound core of VT8235 is almost identical with 8233, thus via82xx driver is the one you need.
Sorry for asking dumb questions here, but I'm still learning the basics of ALSA here.
I've ruled out the possibility of an IRQ conflict, so that's not the cause of my problems. So now I'm wondering, is the ALC201 AC97 codec pretty much identical to the ALC200(P) or ALC202 codecs? I can't find ALC201 in ac97_codec.c. Alsamixer tells me it's using ALC650. Could that be the problem?
Has anyone had success with the VT8235 south bridge? A google search didn't turn up much, I wonder if it's because I'm the only one with the problem, or if it Just Works(tm) with everyone else.
Quoted 1 line
Quoted 1 line
And no, I still can't get sound. :)
Still valid ;)
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by:
Access Your PC Securely with GoToMyPC. Try Free Now
https://www.gotomypc.com/s/OSND/DD
At Sat, 19 Oct 2002 12:21:23 +0200,
Quoted 21 lines · Joachim Blaabjerg
Quoted 12 lines · Takashi Iwai
At Wed, 16 Oct 2002 18:26:12 +0200,
Quoted 8 lines · Joachim Blaabjerg
Quoted 4 lines · you
8235 has the same pci id with 8233, so it's ok.
Takashi
As far as I know, though, the 8235 south bridge uses a different sound chip. VT8233 uses ALC650, while VT8235 uses ALC201. Or am I wrong?
Quoted 6 lines
yes, you are confused among two things.
ALC650 and ALC201 are AC97 codecs, which corresponds to ADC/DAC and mixer parts. it has nothing to do with the sound engine. the sound core of VT8235 is almost identical with 8233, thus via82xx driver is the one you need.
Quoted 8 lines
Sorry for asking dumb questions here, but I'm still learning the basics of ALSA here.
I've ruled out the possibility of an IRQ conflict, so that's not the cause of my problems. So now I'm wondering, is the ALC201 AC97 codec pretty much identical to the ALC200(P) or ALC202 codecs? I can't find ALC201 in
ac97_codec.c. Alsamixer tells me it's using ALC650. Could that be the problem?
If alsamixer tells so, it must be in fact ALC650. ALC20x and ALC650 have different codec ids, which is probed via an AC97 register. Anyway, these chips are almost compatible. So, it doesn't matter much.
Quoted 7 lines
Has anyone had success with the VT8235 south bridge? A google search didn't turn up much, I wonder if it's because I'm the only one with the problem, or if it Just Works(tm) with everyone else.
Quoted 1 line
Quoted 1 line
And no, I still can't get sound. :)
Still valid ;)
Ehm, could you elaborate the symptom?
It could be a bug of the driver itself, of course, although 8233 seems working fine. According to VIA tech, 8235 is compatible with 8233, so theoretically it should work.
Also, please check whether the count in /proc/interrupts increases during playback. If not, it's usually a hardware configuration problem. if it increases, most likely a driver bug.
ciao,
Takashi
-------------------------------------------------------
This sf.net emial is sponsored by: Influence the future of Java(TM) technology. Join the Java Community Process(SM) (JCP(SM)) program now. http://ad.doubleclick.net/clk;4699841;7576301;v?
http://www.sun.com/javavote
Sorry for being unresponsive about this lately.
Quoted 1 line · Takashi Iwai
Ehm, could you elaborate the symptom?
Daniel S. Tarbuck described it very well:
Quoted 9 lines
The modules load and the mixer seems to work, but whenever I try to play some audio, it replays the same bit of audio 13 or 14 times before moving on to the next bit. This takes about 10 seconds, so I sound that loops every 2/3 seconds for 14 loops and then moves on to the next bit of sound (looping 14 times).
This appears to be a timing issue of some sort. When using mpg321, after I stop the player, it reports that it has been playing for less time than it has (roughly 1/14th of the actual time).
Observing the ALSA-user mailing list lately, I see that four or five other people are having the same problem with this driver.
Quoted 3 lines
Also, please check whether the count in
/proc/interruptsincreases during playback. If not, it's usually a hardware configuration problem. if it increases, most likely a driver bug.
Well, in my case it doesn't. I'm 99% sure there are no IRQ conflicts, and I can't see anything else that could be wrong.
I'd gladly give you root access to my machine if that would help you diagnose/fix the problem.
Best Regards,
-------------------------------------------------------
This sf.net email is sponsored by: To learn the basics of securing your web site with SSL, click here to get a FREE TRIAL of a Thawte Server Certificate: http://www.gothawte.com/rd524.html