Skip to contentSkip to conversation

[email protected]

DISCUSSION Mark Ziegler 3 participants 3 messages Nov 21, 2002 – Dec 2, 2002

lore
Share & tools
lore
#0 lore raw

Hi Kai,

thank you. You are right: my ide-dma is turned off. I only activated it in the SUSE setup, but I've never check if it is really switched on. Unfortunately I can not turn on the dma:

linux:/home/woody # hdparm -m 8 -d 1 -u 1 -c 1 /dev/hda /dev/hda:
setting 32-bit IO_support flag to 1
setting multcount to 8
setting unmaskirq to 1 (on)
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted

 multcount    =  8 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  0 (off)

Ok, this is probably because I've bought a brandnew motherboard with a brandnew chipset (VIA KT400). So I will seek around for a dma solution. Anyway, I tried again ecasound:
woody@linux:~> ecasound -z:db -z:intbuf -i alsa,ice_spdif -o test.wav
****************************************************************************
* ecasound v2.0.4 (C) 1997-2001 Kai Vehmanen *
****************************************************************************
(eca-chainsetup) Using double-buffer of 100000 sample frames. (eca-chainsetup) Enabling extra buffering on realtime devices.
- [ Chainsetup/Enabling audio inputs ] ------------------------------------- (eca-audio-objects) Audio object "alsa", mode "read".
(audio-io) Format: s16_le, channels 2, srate 44100, interleaved.
- [ Chainsetup/Enabling audio outputs ] ------------------------------------ (eca-audio-objects) Audio object "test.wav", mode "read/write". (audio-io) Format: s16_le, channels 2, srate 44100, interleaved.
- [ Engine/Init - mixmode "simple" ] --------------------------------------- (eca-main) Prefilling i/o buffers.
(audioio-alsa3) warning! capture overrun - samples lost! Break was at least 7.60 ms long.
(audioio-alsa3) warning! capture overrun - samples lost! Break was at least 215.45 ms long.
(audioio-alsa3) warning! capture overrun - samples lost! Break was at least 0.03 ms long.
- [ Engine/Exiting ] ------------------------------------------------------- (audioio-alsa3) WARNING! While reading from ALSA-pcm device C0D0, there were 3 overruns.

That was only 1 Minute sampling. Sometimes I get up to 500ms. That looks strange to me. Mmmh, I should really hurry up getting my dma to work. 215ms!!!

But thank you very much

Mark

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#1 lore raw

Sorry for the late response..

Quoted 3 lines · Mark Ziegler

thank you. You are right: my ide-dma is turned off. I only activated it in the SUSE setup, but I've never check if it is really switched on. Unfortunately I can not turn on the dma:

[...]

Quoted 11 lines

linux:/home/woody # hdparm -m 8 -d 1 -u 1 -c 1 /dev/hda /dev/hda:
setting 32-bit IO_support flag to 1
setting multcount to 8
setting unmaskirq to 1 (on)
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted

 multcount    =  8 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  0 (off)

This is bad. You should check the linux-kernel archives and other relevant mailing lists... hopefully some newer kernel provides dma-support for your ide-chipset. This is critical for low-latency audio.

Quoted 2 lines

Anyway, I tried again ecasound:
woody@linux:~> ecasound -z:db -z:intbuf -i alsa,ice_spdif -o test.wav

Ok, this will give us quite a lot of info:

Quoted 6 lines

(audioio-alsa3) warning! capture overrun - samples lost! Break was at least 7.60 ms long.
(audioio-alsa3) warning! capture overrun - samples lost! Break was at least 215.45 ms long.
(audioio-alsa3) warning! capture overrun - samples lost! Break was at least 0.03 ms long.

This means that the xruns are caused by process scheduling latencies, not by disk i/o scheduling. The longs xruns are probably caused by disk i/o events that reserve the cpu for a long period of time (dma not used -> all transfers go through the cpu -> trouble). I'd suggest trying low-latency / pre-emption kernel patches, and/or finding a kernel with dma support for your ide chipset.

Signature · 9 lines
 http://www.eca.cx
 Audio software for Linux!



-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
#2 lore raw
Quoted 15 lines · Kai Vehmanen

Sorry for the late response..

Quoted 3 lines · Mark Ziegler

thank you. You are right: my ide-dma is turned off. I only activated it in the SUSE setup, but I've never check if it is really switched on. Unfortunately I can not turn on the dma:

[...]

Quoted 7 lines

linux:/home/woody # hdparm -m 8 -d 1 -u 1 -c 1 /dev/hda /dev/hda:
setting 32-bit IO_support flag to 1
setting multcount to 8
setting unmaskirq to 1 (on)
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted

     ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

FWIW a co-worker and I have both seen this problem recently with Intel's D845EBG2 motherboard. 845E is the chipset on the board. The ICH4 IDE controller (82801DB I/O Controller Hub 4) is supposed to be capable of ATA 66/100. But, with 2.4.19 and 2.4.18 we were unable to set using_dma = 1
When we try we get the same "Operation not permitted" error noted above. My co-worker has worked around it by using the 2.2.20 kernel. For whatever reason the 2.2.20 kernel let's him turn dma on with this chipset. I've chosen to stay with my old box rather than downgrade to the 2.2 series kernel.

I know this isn't a solution, but perhaps the extra info will help someone.

Quoted 9 lines
Quoted 4 lines
 multcount    =  8 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  0 (off)

This is bad. You should check the linux-kernel archives and other relevant mailing lists... hopefully some newer kernel provides dma-support for your ide-chipset. This is critical for low-latency audio.

-Eric Rz.

-------------------------------------------------------
This SF.net email is sponsored by: Get the new Palm Tungsten T handheld. Power & Color in a compact size!
http://ads.sourceforge.net/cgi-bin/redirect.pl?palm0002en