PROBLEM: SYM53C8XX errors while reading tape
[1.] One line summary of the problem:
SYM53C8XX errors while reading tape
[2.] Full description of the problem/report:
I just installed a new Seagate Scorpion 24 tape drive (DDS3 4mm DAT) attached to an old NCR53c810 PCI SCSI controller and was trying it out. I did a:
mt -f /dev/nst0 setblk 32768
tar -C / -b 64 -clvf /dev/nst0 .
and that seemed to work fine, but when I tried to verify or read, with something like this:
mt -f /dev/nst0 rewind
tar -C / -b 64 -dlf /dev/nst0
after a variable delay, i.e. some distance through the process, I get messages to the shell:
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: Too many errors, quitting
tar: Error is not recoverable: exiting now
I can still access the drive afterwards, though the block size gets reset. In /var/log/messages, I see:
Nov 22 00:07:19 celilo kernel: sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14). Nov 22 00:07:19 celilo kernel: sym0: script cmd = 88080000 Nov 22 00:07:19 celilo kernel: sym0: regdump: da 10 80 13 47 08 01 1f 00 01 81 21 80 00 09 00 00 20 e9 37 08 ff ff ff. Nov 22 00:07:19 celilo kernel: sym0: SCSI BUS reset detected. Nov 22 00:07:20 celilo kernel: sym0: SCSI BUS has been reset. Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Current st09:00: sense key Unit Attention Nov 22 00:07:23 celilo kernel: Additional sense indicates Power on,reset,or bus device reset occurred Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
This particular set of messages came under linux-2.4.18, but I had seen what seemed like the same thing under linux-2.5.40 and regressed to 2.4.18 to see if it was a kernel specific problem.
I don't know what the /sbin/fsck those messages mean, in particular the originating error message, codes and register dump. Basically, that is what I am looking for, some indication what the problem might be.
[3.] Keywords (i.e., modules, networking, kernel):
SCSI, error message
[4.] Kernel version (from /proc/version):
Linux version 2.4.18 (root@celilo) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 SMP Sat Jun 1 21:08:44 PDT 2002
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
Linux celilo 2.4.18 #2 SMP Sat Jun 1 21:08:44 PDT 2002 i686 unknown unknown GNU/Linux
Gnu C 2.95.4 Gnu make 3.80 util-linux 2.11u mount 2.11u modutils 2.4.19 e2fsprogs 1.32 Linux C Library 2.3.1 Dynamic linker (ldd) 2.3.1 Procps 3.1.0 Net-tools 1.60 Kbd 1.06 Sh-utils 4.5.3 Modules Loaded ide-scsi
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 8 model name : Pentium III (Coppermine) stepping : 6 cpu MHz : 999.530 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1992.29
processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 8 model name : Pentium III (Coppermine) stepping : 6 cpu MHz : 999.530 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1998.84
[7.3.] Module information (from /proc/modules):
ide-scsi 7808 0
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
$ cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(set)
0cf8-0cff : PCI conf1
a000-a007 : Promise Technology, Inc. 20268
a000-a007 : ide2
a400-a403 : Promise Technology, Inc. 20268
a402-a402 : ide2
a800-a807 : Promise Technology, Inc. 20268
a800-a807 : ide3
ac00-ac03 : Promise Technology, Inc. 20268
ac02-ac02 : ide3
b000-b00f : Promise Technology, Inc. 20268
b000-b007 : ide2
b008-b00f : ide3
b010-b01f : PDC20268
b400-b4ff : 3Dfx Interactive, Inc. Voodoo 3
b800-b8ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
b800-b87f : sym53c8xx
bc00-bc1f : Creative Labs SB Live! EMU10k1
c000-c007 : Creative Labs SB Live!
c400-c407 : Promise Technology, Inc. 20267
c800-c803 : Promise Technology, Inc. 20267
cc00-cc07 : Promise Technology, Inc. 20267
d000-d003 : Promise Technology, Inc. 20267
d400-d43f : Promise Technology, Inc. 20267
d400-d407 : ide4
d408-d40f : ide5
d410-d43f : PDC20267
d800-d83f : Intel Corp. 82557 [Ethernet Pro 100]
d800-d83f : eepro100
dc00-dc0f : VIA Technologies, Inc. Bus Master IDE
dc00-dc07 : ide0
dc08-dc0f : ide1
e000-e01f : VIA Technologies, Inc. UHCI USB
e000-e01f : usb-uhci
e400-e41f : VIA Technologies, Inc. UHCI USB (#2)
e400-e41f : usb-uhci
e800-e81f : VIA Technologies, Inc. UHCI USB (#3)
e800-e81f : usb-uhci $ cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000d0000-000d27ff : Extension ROM
000d3000-000dafff : Extension ROM
000f0000-000fffff : System ROM
00100000-3ffeffff : System RAM
00100000-00266894 : Kernel code
00266895-002d1a9f : Kernel data
3fff0000-3fff2fff : ACPI Non-volatile Storage
3fff3000-3fffffff : ACPI Tables
f8000000-f9ffffff : 3Dfx Interactive, Inc. Voodoo 3
fa000000-fbffffff : 3Dfx Interactive, Inc. Voodoo 3
fd000000-fd3fffff : VIA Technologies, Inc. VT8633 [Apollo Pro266]
fd400000-fd4fffff : Intel Corp. 82557 [Ethernet Pro 100]
fd500000-fd51ffff : Promise Technology, Inc. 20267
fd520000-fd523fff : Promise Technology, Inc. 20268
fd524000-fd524fff : Intel Corp. 82557 [Ethernet Pro 100]
fd524000-fd524fff : eepro100
fd525000-fd5250ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
fec00000-ffffffff : reserved[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266] (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=4M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra100TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory at fd520000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc. Voodoo3
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at fa000000 (32-bit, prefetchable) [size=32M]
Region 2: I/O ports at b400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly NCR) 53c810 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at fd525000 (32-bit, non-prefetchable) [size=256]
00:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs: Unknown device 8071
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at bc00 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at c000 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 RAID bus controller: Promise Technology, Inc. 20267 (rev 02)
Subsystem: Promise Technology, Inc. Fasttrak100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c400 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at d000 [size=4]
Region 4: I/O ports at d400 [size=64]
Region 5: Memory at fd500000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corp. EtherExpress PRO/100+ Server Adapter (PILA8470B)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd524000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d800 [size=64]
Region 2: Memory at fd400000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=2 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at dc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.4 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
$ cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7350
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: DualPort Model: Reader 2 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 01
Vendor: DualPort Model: Reader 2 Rev:
Type: Direct-Access ANSI SCSI revision: 02[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you think to be relevant):
Here are the relevant messages from dmesg:
SCSI subsystem driver Revision: 1.00
sym.0.9.0: setting PCI_COMMAND_PARITY...
sym0: <810> rev 0x2 on pci bus 0 device 9 function 0 irq 11
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7350
Type: Sequential-Access ANSI SCSI revision: 02
st: Version 20020205, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs 16 Attached scsi tape st0 at scsi0, channel 0, id 1, lun 0
[...]
sym0:1: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
st0: Block limits 1 - 16777215 bytes.
This is the end of the boot messages, then when the error occurs, I get the following:
sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14).
sym0: script cmd = 88080000
sym0: regdump: da 10 80 13 47 08 01 1f 00 01 81 21 80 00 09 00 00 20 e9 37 08 ff ff ff.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
st0: Error with sense data: Current st09:00: sense key Unit Attention Additional sense indicates Power on,reset,or bus device reset occurred
st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Additional sense indicates Logical unit is in process of becoming ready
[...]
Signature · 4 lines
Russell Senior ``I've seen every kind of critter God ever made, [email protected] and I ain't never seen a meaner, lower, more stinkin' yellow hypocrite than you!'' -- Burl Ives as Rufus Hennessy
Russel,
The source of the problem is a severe error reported by the chip; Here is what the driver said about:
Quoted 1 line
sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14).
The relevant part is the c8 value (SIST = SCSI Interrupt Status). Btw there is some notes in the file Documentation.txt supplied with the sym53c8xx_2 driver (15.2 Understanding hardware error reports).
Here an excerpt:
-- begin --
sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ (script 7c0:19000000). .....A.........B.C....D.E..F....G.H..I.......J.....K...L.......
...
Field C : SIST io register (SCSI Interrupt Status)
Bit 0x08 : SGE SCSI GROSS ERROR
Indicates that the chip detected a severe error condition on the SCSI BUS that prevents the SCSI protocol from functionning properly.
Bit 0x04 : UDC Undexpected Disconnection
Indicates that the device released the SCSI BUS when the chip was not expecting this to happen. A device may behave so to
indicate the SCSI initiator that an error condition not reportable using the SCSI protocol has occured.
Bit 0x02 : RST SCSI BUS Reset
Generally SCSI targets donnot reset the SCSI BUS, although any device on the BUS can reset it at any time.
Bit 0x01 : PAR Parity
SCSI parity error detected.
On a faulty SCSI BUS, any error condition among SGE (0x08), UDC (0x04) and PAR (0x01) may be detected by the chip. If your SCSI system sometimes encounters such error conditions, especially SCSI GROSS ERROR, then a SCSI BUS problem is likely the cause of these errors.
For fields D,E,F,G and H, you may look into the sym53c8xx_defs.h file that contains some minimal comments on IO register bits.
-- end --
c8 contains bit 8 which indicates a SCSI GROSS ERROR reported by the chip. Most of the time a SCSI BUS problem is the cause.
You may check the BUS, check or swap if possible cable and/or termination and see if it makes difference.
Gérard.
Quoted 456 lines · Russell Senior
[1.] One line summary of the problem:
SYM53C8XX errors while reading tape
[2.] Full description of the problem/report:
I just installed a new Seagate Scorpion 24 tape drive (DDS3 4mm DAT) attached to an old NCR53c810 PCI SCSI controller and was trying it out. I did a:
mt -f
/dev/nst0setblk 32768
tar -C / -b 64 -clvf/dev/nst0.and that seemed to work fine, but when I tried to verify or read, with something like this:
mt -f
/dev/nst0rewind
tar -C / -b 64 -dlf/dev/nst0after a variable delay, i.e. some distance through the process, I get messages to the shell:
tar:
/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar:/dev/nst0: Cannot read: Input/output error
tar: Too many errors, quitting
tar: Error is not recoverable: exiting nowI can still access the drive afterwards, though the block size gets reset. In
/var/log/messages, I see:Nov 22 00:07:19 celilo kernel: sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14). Nov 22 00:07:19 celilo kernel: sym0: script cmd = 88080000 Nov 22 00:07:19 celilo kernel: sym0: regdump: da 10 80 13 47 08 01 1f 00 01 81 21 80 00 09 00 00 20 e9 37 08 ff ff ff. Nov 22 00:07:19 celilo kernel: sym0: SCSI BUS reset detected. Nov 22 00:07:20 celilo kernel: sym0: SCSI BUS has been reset. Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Current st09:00: sense key Unit Attention Nov 22 00:07:23 celilo kernel: Additional sense indicates Power on,reset,or bus device reset occurred Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming readyThis particular set of messages came under linux-2.4.18, but I had seen what seemed like the same thing under linux-2.5.40 and regressed to 2.4.18 to see if it was a kernel specific problem.
I don't know what the
/sbin/fsckthose messages mean, in particular the originating error message, codes and register dump. Basically, that is what I am looking for, some indication what the problem might be.[3.] Keywords (i.e., modules, networking, kernel):
SCSI, error message
[4.] Kernel version (from
/proc/version):Linux version 2.4.18 (root@celilo) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 SMP Sat Jun 1 21:08:44 PDT 2002
[7.] Environment
[7.1.] Software (add the output of thever_linuxscript here)Linux celilo 2.4.18 #2 SMP Sat Jun 1 21:08:44 PDT 2002 i686 unknown unknown GNU/Linux
Gnu C 2.95.4 Gnu make 3.80 util-linux 2.11u mount 2.11u modutils 2.4.19 e2fsprogs 1.32 Linux C Library 2.3.1 Dynamic linker (ldd) 2.3.1 Procps 3.1.0 Net-tools 1.60 Kbd 1.06 Sh-utils 4.5.3 Modules Loaded ide-scsi[7.2.] Processor information (from
/proc/cpuinfo):processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 8 model name : Pentium III (Coppermine) stepping : 6 cpu MHz : 999.530 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1992.29processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 8 model name : Pentium III (Coppermine) stepping : 6 cpu MHz : 999.530 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1998.84[7.3.] Module information (from
/proc/modules):ide-scsi 7808 0
[7.4.] Loaded driver and hardware information (
/proc/ioports,/proc/iomem)$ cat /proc/ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 02f8-02ff : serial(set) 0376-0376 : ide1 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(set) 0cf8-0cff : PCI conf1 a000-a007 : Promise Technology, Inc. 20268 a000-a007 : ide2 a400-a403 : Promise Technology, Inc. 20268 a402-a402 : ide2 a800-a807 : Promise Technology, Inc. 20268 a800-a807 : ide3 ac00-ac03 : Promise Technology, Inc. 20268 ac02-ac02 : ide3 b000-b00f : Promise Technology, Inc. 20268 b000-b007 : ide2 b008-b00f : ide3 b010-b01f : PDC20268 b400-b4ff : 3Dfx Interactive, Inc. Voodoo 3 b800-b8ff : LSI Logic / Symbios Logic (formerly NCR) 53c810 b800-b87f : sym53c8xx bc00-bc1f : Creative Labs SB Live! EMU10k1 c000-c007 : Creative Labs SB Live! c400-c407 : Promise Technology, Inc. 20267 c800-c803 : Promise Technology, Inc. 20267 cc00-cc07 : Promise Technology, Inc. 20267 d000-d003 : Promise Technology, Inc. 20267 d400-d43f : Promise Technology, Inc. 20267 d400-d407 : ide4 d408-d40f : ide5 d410-d43f : PDC20267 d800-d83f : Intel Corp. 82557 [Ethernet Pro 100] d800-d83f : eepro100 dc00-dc0f : VIA Technologies, Inc. Bus Master IDE dc00-dc07 : ide0 dc08-dc0f : ide1 e000-e01f : VIA Technologies, Inc. UHCI USB e000-e01f : usb-uhci e400-e41f : VIA Technologies, Inc. UHCI USB (#2) e400-e41f : usb-uhci e800-e81f : VIA Technologies, Inc. UHCI USB (#3) e800-e81f : usb-uhci$ cat /proc/iomem 00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000d0000-000d27ff : Extension ROM 000d3000-000dafff : Extension ROM 000f0000-000fffff : System ROM 00100000-3ffeffff : System RAM 00100000-00266894 : Kernel code 00266895-002d1a9f : Kernel data 3fff0000-3fff2fff : ACPI Non-volatile Storage 3fff3000-3fffffff : ACPI Tables f8000000-f9ffffff : 3Dfx Interactive, Inc. Voodoo 3 fa000000-fbffffff : 3Dfx Interactive, Inc. Voodoo 3 fd000000-fd3fffff : VIA Technologies, Inc. VT8633 [Apollo Pro266] fd400000-fd4fffff : Intel Corp. 82557 [Ethernet Pro 100] fd500000-fd51ffff : Promise Technology, Inc. 20267 fd520000-fd523fff : Promise Technology, Inc. 20268 fd524000-fd524fff : Intel Corp. 82557 [Ethernet Pro 100] fd524000-fd524fff : eepro100 fd525000-fd5250ff : LSI Logic / Symbios Logic (formerly NCR) 53c810 fec00000-ffffffff : reserved[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266] (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory atfd000000(32-bit, prefetchable) [size=4M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:07.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra100TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory atfd520000(32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:08.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc. Voodoo3
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 10
Region 0: Memory atf8000000(32-bit, non-prefetchable) [size=32M]
Region 1: Memory atfa000000(32-bit, prefetchable) [size=32M]
Region 2: I/O ports at b400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:09.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly NCR) 53c810 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory atfd525000(32-bit, non-prefetchable) [size=256]00:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs: Unknown device 8071
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at bc00 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:0a.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at c000 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:0c.0 RAID bus controller: Promise Technology, Inc. 20267 (rev 02)
Subsystem: Promise Technology, Inc. Fasttrak100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c400 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at d000 [size=4]
Region 4: I/O ports at d400 [size=64]
Region 5: Memory atfd500000(32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corp. EtherExpress PRO/100+ Server Adapter (PILA8470B)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory atfd524000(32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d800 [size=64]
Region 2: Memory atfd400000(32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=2 PME-00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at dc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-00:11.4 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-[7.6.] SCSI information (from
/proc/scsi/scsi)$ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 01 Lun: 00 Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7350 Type: Sequential-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: DualPort Model: Reader 2 Rev: Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 00 Lun: 01 Vendor: DualPort Model: Reader 2 Rev: Type: Direct-Access ANSI SCSI revision: 02[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you think to be relevant):Here are the relevant messages from dmesg:
SCSI subsystem driver Revision: 1.00
sym.0.9.0: settingPCI_COMMAND_PARITY...
sym0: <810> rev0x2on pci bus 0 device 9 function 0 irq 11
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7350
Type: Sequential-Access ANSI SCSI revision: 02
st: Version 20020205, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs 16 Attached scsi tape st0 at scsi0, channel 0, id 1, lun 0[...]
sym0:1: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
st0: Block limits 1 - 16777215 bytes.This is the end of the boot messages, then when the error occurs, I get the following:
sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14).
sym0: script cmd = 88080000
sym0: regdump: da 10 80 13 47 08 01 1f 00 01 81 21 80 00 09 00 00 20 e9 37 08 ff ff ff.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
st0: Error with sense data: Current st09:00: sense key Unit Attention Additional sense indicates Power on,reset,or bus device reset occurred
st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready Additional sense indicates Logical unit is in process of becoming ready[...]
Quoted 11 lines
--
Russell Senior ``I've seen every kind of critter God ever made,
[email protected] and I ain't never seen a meaner, lower, more
stinkin' yellow hypocrite than you!''
-- Burl Ives as Rufus Hennessy
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html