Skip to contentSkip to conversation

Disk problems

parisc-linux James Smith 6 participants 11 messages Nov 22, 2002 – Nov 27, 2002

lore
Share & tools
lore
#0 lore raw

I just got a pile of 712/60's - $80 for 10 of em :)

i've set one up & now i'm going through the disks one at a time & cloning them as its quicker than going through the install each time

i've hit one disk that gives me this whenever i try to fdisk it

sixty:~# fdisk /dev/sdb

Unable to read /dev/sdb

when i tried to zero the disk, i got this....

sixty:~# dd if=/dev/zero of=/dev/sdb count=1 bs=512 
dd: writing `/dev/sdb': Input/output error
1+0 records in
0+0 records out

the console sees the disk when i use search

does this indicate a dead disk?

the disk was ok until i put it into a mac......

James S

#1 lore raw

Well quit putting them in those darn macs....just kidding. Who makes the disk? IBM has certain tools like their drive fitness tests that has saved me a few times. Seagate and others probably have similar tools. Check their support sites and it may just be a matter of the wrong block size written by your mac. IBM drives are especially notorious for having weird block sizes and such. derek
James Smith <[email protected]> wrote:I just got a pile of 712/60's - $80 for 10 of em :)

i've set one up & now i'm going through the disks one at a time & cloning them as its quicker than going through the install each time

i've hit one disk that gives me this whenever i try to fdisk it

sixty:~# fdisk /dev/sdb

Unable to read /dev/sdb

when i tried to zero the disk, i got this....

sixty:~# dd if=/dev/zero of=/dev/sdb count=1 bs=512 
dd: writing `/dev/sdb': Input/output error
1+0 records in
0+0 records out

the console sees the disk when i use search

does this indicate a dead disk?

the disk was ok until i put it into a mac......

James S

_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now

#2 lore raw

its the original seagate disk that came with it

the disk still works in the mac, so its not dead

i dont have anything other than macs & the workstations that are scsi

would a low level format on the mac do the same as low level using an adaptec card ?

James S

Quoted 44 lines · Derek Engelhaupt

Well quit putting them in those darn macs....just kidding. Who makes the disk? IBM has certain tools like their drive fitness tests that has saved me a few times. Seagate and others probably have similar tools. Check their support sites and it may just be a matter of the wrong block size written by your mac. IBM drives are especially notorious for having weird block sizes and such. derek
James Smith <[email protected]> wrote:I just got a pile of 712/60's - $80 for 10 of em :)

i've set one up & now i'm going through the disks one at a time & cloning them as its quicker than going through the install each time

i've hit one disk that gives me this whenever i try to fdisk it

sixty:~# fdisk /dev/sdb

Unable to read /dev/sdb

when i tried to zero the disk, i got this....

sixty:~# dd if=/dev/zero of=/dev/sdb count=1 bs=512 
dd: writing `/dev/sdb': Input/output error
1+0 records in
0+0 records out

the console sees the disk when i use search

does this indicate a dead disk?

the disk was ok until i put it into a mac......

James S

_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now

#3 lore raw

Hi James,

Sorry in advance if you already do it,

Quoted 10 lines

its the original seagate disk that came with it

the disk still works in the mac, so its not dead

i dont have anything other than macs & the workstations that are scsi

would a low level format on the mac do the same as low level using an adaptec card ?

Don't you still have a hpux support+ cd to boot on it and test your disk with ODE?

[I encounter a strange problem which I do not yet fix:
I used a data disk which crashed and replaced by HP but new FW release. When I put it back in my scsi chain, I was unable to use: a lot of scsi reset. OTC when I chek it on a hpux box no problem as well if I connect it alone to my hppalinux box ?]

Regards,
Joel

********************************************************************************
Controlez mieux votre consommation Internet...surfez Tiscali Complete...http://tiscali.complete.be

#4 lore raw
Quoted 5 lines · [email protected] wrote:

[I encounter a strange problem which I do not yet fix:
I used a data disk which crashed and replaced by HP but new FW release. When I put it back in my scsi chain, I was unable to use: a lot of scsi reset. OTC when I chek it on a hpux box no problem as well if I connect it alone to my hppalinux box ?]

upgrading firmware should never result in lots of scsi resets. Sounds more like a problem with the HW configuration. Check SCSI IDs, cable lengths, and termination.

grant

#5 lore raw
In reply to James Smith
Quoted 2 lines

would a low level format on the mac do the same as low level using an adaptec card ?

If it works in a mac, the low-level formatting is probably ok. It's most likely the data in block 0 or possibly some of the vendor info that's the problem. You should also examine all switch settings and check that the termination is correct.

Erase disk in the finder doesn't do a low-level format. It just builds a new file systems. Various tools from Adaptec (FWB HDT) and other vendors are available to do low-level formats on the Mac. The Sedit program can probably issue a command to format the drive but I would only do this as a last resort.

Dave

Signature · 2 lines
J. David Anglin                                  [email protected]
National Research Council of Canada              (613) 990-0752 (FAX: 952-6605)
#6 lore raw

http://www.seagate.com/support/seatools/index.html
I would try that tool. I had a similar issue with an IBM drive and downloaded their disk test tool and the analysis of the drive fixed the issue. This tool however only runs on Intel based systems. Maybe a friend has a single ended SCSI card you could test with on a Winblows box? derek
John David Anglin <[email protected]> wrote:> would a low level format on the mac do the same as low level using an

Quoted 1 line

adaptec card ?

If it works in a mac, the low-level formatting is probably ok. It's most likely the data in block 0 or possibly some of the vendor info that's the problem. You should also examine all switch settings and check that the termination is correct.

Erase disk in the finder doesn't do a low-level format. It just builds a new file systems. Various tools from Adaptec (FWB HDT) and other vendors are available to do low-level formats on the Mac. The Sedit program can probably issue a command to format the drive but I would only do this as a last resort.

Dave

Signature · 11 lines
J. David Anglin [email protected]
National Research Council of Canada (613) 990-0752 (FAX: 952-6605)
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux


---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now
#7 lore raw
Quoted 4 lines · Derek Engelhaupt

If it works in a mac, the low-level formatting is probably ok. It's most likely the data in block 0 or possibly some of the vendor info that's the problem. You should also examine all switch settings and check that the termination is correct.

I privately speculating the nwe disk FW talks to the host differently. ie it might disconnect/reconnect or send "msg" when the SCSI driver is expecting something else. That at least would explain why mac or hpux can deal with the disk but linux can't.

grant

#8 lore raw

[parisc-linux] Dual Video Cards?

In reply to John David Anglin

Anyone running dual displays on a C Class? And if so how? I understand it needs two video cards or one card with dual output. Thanks.....

derek

---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now

#9 lore raw

Re: [parisc-linux] Dual Video Cards?

Quoted 3 lines · ext Derek Engelhaupt

Anyone running dual displays on a C Class? And if so how? I understand it needs two video cards or one card with dual output. Thanks.....

Well, I have both a VIS-EG/PCI and a VIS-EG/GSC in a C360, but it's running HP-UX and not Linux.

Hardware-wise it isn't a problem, even though the GSC card isn't officially supported in a C360. You might want to check the boot consols config though, diagnosing display problems with that during boot isn't fun without a serial console. And if you want to have a graphics console, do mind the slot designations ... I wouldn't try to make the GSC card the console in the C360, for example.

Don't know how you'd go about configuring those in Linux though. In HP-UX it's rather simple but that doesn't help much...

Signature · 2 lines
Mikko Nahkola   <[email protected]>
Tre-IN sysadmin <[email protected]>
#10 lore raw

Re: [parisc-linux] Dual Video Cards?

Well that's going to be my exact setup...I have one PCI EG card on the way and it came with a GSC EG card that I'm using now. This machine dual boots HPUX and Linux of a Model 12 Autoraid with 2 LUNS on it. I guess I'll get it working with HPUX first then tackle the Linux side. I do have access to a serial console and that's how I got the original GSC graphics card configured to work. Right now the GSC card is the default console and it works fine. I found it interesting that the new palinux-2.4.19-pa24-PDC-20021106-netinst.iso doesn't exhibit the long bus walk times that I've been hearing about unless I have my kernal versions confused. Like others here I, my network won't hook up to the switch at 100FD only 10FD. The more interesting thing is that it hooks up at 100FD during the install phase of Linux for the netinst CD, but not after it's running on it's own kernal. I do believe someone wrote a patch for this though. derek

Quoted 3 lines · ext Derek Engelhaupt

Anyone running dual displays on a C Class? And if so how? I understand it needs two video cards or one card with dual output. Thanks.....

Well, I have both a VIS-EG/PCI and a VIS-EG/GSC in a C360, but it's running HP-UX and not Linux.

Hardware-wise it isn't a problem, even though the GSC card isn't officially supported in a C360. You might want to check the boot consols config though, diagnosing display problems with that during boot isn't fun without a serial console. And if you want to have a graphics console, do mind the slot designations ... I wouldn't try to make the GSC card the console in the C360, for example.

Don't know how you'd go about configuring those in Linux though. In HP-UX it's rather simple but that doesn't help much...

Signature · 11 lines
Mikko Nahkola 
Tre-IN sysadmin 
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux


---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now