RH73 Promise ATA/133 Install Problems
I have a Gigabyte GA-7VRXP motherboard which has an on-board Promise 20276 ATA133/RAID controller. I want to install RH73, on the two ATA133 drives connected to the Promise controller. I've set up the motherboard BIOS with the Promise 20276 interfaces as ATA (not RAID), and I want to install on the two drives in a software RAID configuration.
If I start the standard RH73 install it does not identify the two drives connected to the Promise interfaces. I tried installing with the RedHat "Supplemental Drivers" disk/floppy, but it doesn't seem to have a driver for the Promise. I tried installing with the Promise ATA/RAID drivers downloaded from their site, but their drivers seem to support only the "hardware" RAID configuration, not plain drives on which I would set up software RAID.
Anyone know of a solution? In general I believe there are Promise and/or ATA133 drivers included in the kernel, and I could set up a custom drivers disk with those to use in the install, but I don't know how to do that (if that's the solution, instructions or pointers to a howto would be appreciated). Or, there may be an easier way. Advice appreciated.
(BTW I've had enough problems with Promise "hardware" RAID in the past that I prefer to avoid this. Subsequent to the initial install I will do a custom kernel to support some other PCI hardware I want to use in the box, and I've found that upgrading after installing on Promise hardware RAID can be problematical. Given use of software RAID, I am interested in knowing what's the best kernel version or patch to use for stability and performance).
Pls cc me direct as I'm not a list subscriber - Thanx, Randy
Quoted 9 lines
I have a Gigabyte GA-7VRXP motherboard which has an on-board Promise 20276 ATA133/RAID controller. I want to install RH73, on the two ATA133 drives connected to the Promise controller. I've set up the motherboard BIOS with the Promise 20276 interfaces as ATA (not RAID), and I want to install on the two drives in a software RAID configuration.
If I start the standard RH73 install it does not identify the two drives connected to the Promise interfaces.
Support for the Promise 20276 went in to the kernel at 2.4.19-pre6.
Can you get to a command prompt and post the output of lspci -v -v? Maybe it has a non standard PCI id and is not being recognised.
John.
# lspci -v -v
00:0f.0 RAID bus controller: Promise Technology, Inc. PDC20276 IDE (rev 01) (prog-if 85)
Subsystem: Giga-byte Technology: Unknown device b001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e800 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at dffc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Quoted 17 lines · John Bradford
Quoted 9 lines
I have a Gigabyte GA-7VRXP motherboard which has an on-board Promise 20276 ATA133/RAID controller. I want to install RH73, on the two ATA133 drives connected to the Promise controller. I've set up the motherboard BIOS with the Promise 20276 interfaces as ATA (not RAID), and I want to install on the two drives in a software RAID configuration.
If I start the standard RH73 install it does not identify the two drives connected to the Promise interfaces.
Support for the Promise 20276 went in to the kernel at 2.4.19-pre6.
Can you get to a command prompt and post the output of lspci -v -v? Maybe it has a non standard PCI id and is not being recognised.
John.
Quoted 13 lines
Quoted 13 lines
Quoted 10 lines
I have a Gigabyte GA-7VRXP motherboard which has an on-board Promise 20276 ATA133/RAID controller. I want to install RH73, on the two ATA133 drives connected to the Promise controller. I've set up the motherboard BIOS with the Promise 20276 interfaces as ATA (not RAID), and I want to install on the two drives in a software RAID configuration.
If I start the standard RH73 install it does not identify the two drives connected to the Promise interfaces.
Support for the Promise 20276 went in to the kernel at 2.4.19-pre6.
Quoted 8 lines
Quoted 2 lines
Can you get to a command prompt and post the output of lspci -v -v? Maybe it has a non standard PCI id and is not being recognised.
# lspci -v -v00:0f.0 RAID bus controller: Promise Technology, Inc. PDC20276 IDE (rev
01) (prog-if 85)
Subsystem: Giga-byte Technology: Unknown device b001
That might be the problem. If that ID is added to the correct list it may well work.
John.