visws: move header file into asm/arch-visws (6/13)

diff -urN -X /usr/share/dontdiff linux-2.5.60.vanilla/include/asm-i386/mach-visws/cobalt.h linux-2.5.60/include/asm-i386/mach-visws/cobalt.h
@@ -0,0 +1,125 @@
+#ifndef __I386_SGI_COBALT_H
+#define __I386_SGI_COBALT_H
+
+#include <asm/fixmap.h>
+
+/*
+ * Cobalt SGI Visual Workstation system ASIC
+ */ 
+
+#define CO_CPU_NUM_PHYS 0x1e00
+#define CO_CPU_TAB_PHYS (CO_CPU_NUM_PHYS + 2)
+
+#define CO_CPU_MAX 4
+
+#define	CO_CPU_PHYS		0xc2000000
+#define	CO_APIC_PHYS		0xc4000000
+
+/* see set_fixmap() and asm/fixmap.h */
+#define	CO_CPU_VADDR		(fix_to_virt(FIX_CO_CPU))
+#define	CO_APIC_VADDR		(fix_to_virt(FIX_CO_APIC))
+
+/* Cobalt CPU registers -- relative to CO_CPU_VADDR, use co_cpu_*() */
+#define	CO_CPU_REV		0x08
+#define	CO_CPU_CTRL		0x10
+#define	CO_CPU_STAT		0x20
+#define	CO_CPU_TIMEVAL		0x30
+
+/* CO_CPU_CTRL bits */
+#define	CO_CTRL_TIMERUN		0x04		/* 0 == disabled */
+#define	CO_CTRL_TIMEMASK	0x08		/* 0 == unmasked */
+
+/* CO_CPU_STATUS bits */
+#define	CO_STAT_TIMEINTR	0x02	/* (r) 1 == int pend, (w) 0 == clear */
+
+/* CO_CPU_TIMEVAL value */
+#define	CO_TIME_HZ		100000000	/* Cobalt core rate */
+
+/* Cobalt APIC registers -- relative to CO_APIC_VADDR, use co_apic_*() */
+#define	CO_APIC_HI(n)		(((n) * 0x10) + 4)
+#define	CO_APIC_LO(n)		((n) * 0x10)
+#define	CO_APIC_ID		0x0ffc
+
+/* CO_APIC_ID bits */
+#define	CO_APIC_ENABLE		0x00000100
+
+/* CO_APIC_LO bits */
+#define	CO_APIC_MASK		0x00010000	/* 0 = enabled */
+#define	CO_APIC_LEVEL		0x00008000	/* 0 = edge */
+
+/*
+ * Where things are physically wired to Cobalt
+ * #defines with no board _<type>_<rev>_ are common to all (thus far)
+ */
+#define	CO_APIC_IDE0		4
+#define CO_APIC_IDE1		2		/* Only on 320 */
+
+#define	CO_APIC_8259		12		/* serial, floppy, par-l-l */
+
+/* Lithium PCI Bridge A -- "the one with 82557 Ethernet" */
+#define	CO_APIC_PCIA_BASE0	0 /* and 1 */	/* slot 0, line 0 */
+#define	CO_APIC_PCIA_BASE123	5 /* and 6 */	/* slot 0, line 1 */
+
+#define	CO_APIC_PIIX4_USB	7		/* this one is wierd */
+
+/* Lithium PCI Bridge B -- "the one with PIIX4" */
+#define	CO_APIC_PCIB_BASE0	8 /* and 9-12 *//* slot 0, line 0 */
+#define	CO_APIC_PCIB_BASE123	13 /* 14.15 */	/* slot 0, line 1 */
+
+#define	CO_APIC_VIDOUT0		16
+#define	CO_APIC_VIDOUT1		17
+#define	CO_APIC_VIDIN0		18
+#define	CO_APIC_VIDIN1		19
+
+#define	CO_APIC_LI_AUDIO	22
+
+#define	CO_APIC_AS		24
+#define	CO_APIC_RE		25
+
+#define CO_APIC_CPU		28		/* Timer and Cache interrupt */
+#define	CO_APIC_NMI		29
+#define	CO_APIC_LAST		CO_APIC_NMI
+
+/*
+ * This is how irqs are assigned on the Visual Workstation.
+ * Legacy devices get irq's 1-15 (system clock is 0 and is CO_APIC_CPU).
+ * All other devices (including PCI) go to Cobalt and are irq's 16 on up.
+ */
+#define	CO_IRQ_APIC0	16			/* irq of apic entry 0 */
+#define	IS_CO_APIC(irq)	((irq) >= CO_IRQ_APIC0)
+#define	CO_IRQ(apic)	(CO_IRQ_APIC0 + (apic))	/* apic ent to irq */
+#define	CO_APIC(irq)	((irq) - CO_IRQ_APIC0)	/* irq to apic ent */
+#define CO_IRQ_IDE0	14			/* knowledge of... */
+#define CO_IRQ_IDE1	15			/* ... ide driver defaults! */
+#define	CO_IRQ_8259	CO_IRQ(CO_APIC_8259)
+
+#ifdef CONFIG_X86_VISWS_APIC
+extern __inline void co_cpu_write(unsigned long reg, unsigned long v)
+{
+	*((volatile unsigned long *)(CO_CPU_VADDR+reg))=v;
+}
+
+extern __inline unsigned long co_cpu_read(unsigned long reg)
+{
+	return *((volatile unsigned long *)(CO_CPU_VADDR+reg));
+}            
+             
+extern __inline void co_apic_write(unsigned long reg, unsigned long v)
+{
+	*((volatile unsigned long *)(CO_APIC_VADDR+reg))=v;
+}            
+             
+extern __inline unsigned long co_apic_read(unsigned long reg)
+{
+	return *((volatile unsigned long *)(CO_APIC_VADDR+reg));
+}
+#endif
+
+extern char visws_board_type;
+
+#define	VISWS_320	0
+#define	VISWS_540	1
+
+extern char visws_board_rev;
+
+#endif /* __I386_SGI_COBALT_H */

53 lines not on this page · raw message

107 lines not on this page · raw message

117 lines not on this page · raw message

45 lines not on this page · raw message