Skip to contentSkip to conversation

2.5 AGP for 2.4.21-pre4

DISCUSSION Brian Jackson 3 participants 6 messages Feb 16, 2003 – Feb 19, 2003

lore
Share & tools
lore
#0 lore raw

This is a poor attempt at a backport of the 2.5.61 AGP subsystem by someone who doesn't know what he is doing and is in way over his head. That said, are there any "brave" souls out there that want to try this out with an AGP3 card and 2.4.21pre4. I compile/boot tested it with an old ati card, but I don't have an AGP 3.0 card/MB to test it on. I got into X and ran glxgears using this kernel(I am using it to finish writing this email)

http://www.mdrx.com/brian/2.4.21-pre4-2.5agp.diff.gz

caveats:
agp has to be built in to the kernel (no modules)

I did the following:
copied the drivers/char/agp directory from 2.5.61
copied include/asm-*/agp.h from 2.5.61
copied include/linux/*agp.h from 2.5.61
made some changes to drivers/char/agp/Makefile
on line 619&635 of frontend.c changed remap_page_range to only have 4
arguments
line 705 generic.c changed SetPageLocked -->SetPageReserved
(not sure if this is right, but Locked doesn't exist in 2.4 and I thought Reserved might work -- Let me know if this should be something else)
backend.c:241 & backend.c:263 commented references to 2.5 module stuff
(therefore this only safe to be built into the kernel for now, any ideas what I should use here instead?)
added some device id's to drivers/char/agp/agp.h from

	2.5.61/include/linux/pci_ids.h

uninclude gfp.h & linux/page-flags.h from amd-k7-agp.c

What else I need to do:
change to old style module init stuff

This is nowhere near suitable for production use, but I would like some people that actually have AGP3 cards/MB's to try this out

--Brian Jackson

P.S. All criticism is welcome even flaming since I am in a decent mood right now

P.S.S. To Dave Jones -- I thought 2.5 had support for VIA chipsets & AGP3, but I only saw config options for the 7205/7505

#1 lore raw
Quoted 2 lines · Brian Jackson

P.S.S. To Dave Jones -- I thought 2.5 had support for VIA chipsets & AGP3, but I only saw config options for the 7205/7505

If CONFIG_AGP3 is set, then the agp3 routines in via-agp.c also get built, so you get KT400 support.

Dave

Signature · 1 line
| Dave Jones.        http://www.codemonkey.org.uk
#2 lore raw
Quoted 8 lines · Dave Jones
Quoted 2 lines · Brian Jackson

P.S.S. To Dave Jones -- I thought 2.5 had support for VIA chipsets & AGP3, but I only saw config options for the 7205/7505

If CONFIG_AGP3 is set, then the agp3 routines in via-agp.c also get built, so you get KT400 support.

Dave

That is what it looked like as I started looking through some of the code, I just wasn't sure. Thanks for the answer.

--Brian Jackson

#3 lore raw
In reply to Brian Jackson

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

You patch deleted the definitions for the Via chipsets. After I added them back the agpgart driver appeared to load correctly. When I try to start X I get a black screen and have to shutdown and reboot to get video back. This is with an AIW 9700 Pro and a Gigabyte GA-7VAXP KT400 based motherboard .

- -- Edward Killips

- -----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Brian Jackson
Sent: Saturday, February 15, 2003 10:35 PM
To: [email protected]; [email protected]; [email protected]
Subject: 2.5 AGP for 2.4.21-pre4

This is a poor attempt at a backport of the 2.5.61 AGP subsystem by someone who doesn't know what he is doing and is in way over his head. That said, are
there any "brave" souls out there that want to try this out with an AGP3 card
and 2.4.21pre4. I compile/boot tested it with an old ati card, but I don't have an AGP 3.0 card/MB to test it on. I got into X and ran glxgears using this kernel(I am using it to finish writing this email)

http://www.mdrx.com/brian/2.4.21-pre4-2.5agp.diff.gz

caveats:
agp has to be built in to the kernel (no modules)

I did the following:
copied the drivers/char/agp directory from 2.5.61
copied include/asm-*/agp.h from 2.5.61
copied include/linux/*agp.h from 2.5.61
made some changes to drivers/char/agp/Makefile
on line 619&635 of frontend.c changed remap_page_range to only have 4
arguments
line 705 generic.c changed SetPageLocked -->SetPageReserved
(not sure if this is right, but Locked doesn't exist in 2.4 and I thought Reserved might work -- Let me know if this should be something else)
backend.c:241 & backend.c:263 commented references to 2.5 module stuff
(therefore this only safe to be built into the kernel for now, any ideas
what
I should use here instead?)
added some device id's to drivers/char/agp/agp.h from

	2.5.61/include/linux/pci_ids.h

uninclude gfp.h & linux/page-flags.h from amd-k7-agp.c

What else I need to do:
change to old style module init stuff

This is nowhere near suitable for production use, but I would like some people
that actually have AGP3 cards/MB's to try this out

- --Brian Jackson

P.S. All criticism is welcome even flaming since I am in a decent mood right now

P.S.S. To Dave Jones -- I thought 2.5 had support for VIA chipsets & AGP3, but
I only saw config options for the 7205/7505

- -
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0

iQA/AwUBPlDY2Xg7wzlNS3haEQLFswCfU0OJLlObv53E0kII4VpQJfQeDNEAoLSz 0h6O30p+lfi7kjuj28Mv6vpN
=kwgx
-----END PGP SIGNATURE-----

#4 lore raw

<snipped DaveJ from cc: he is a busy man these days>

Quoted 4 lines · Edward Killips

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

You patch deleted the definitions for the Via chipsets.

you mean for other parts of the chipset? Not for the agp bridge, right? Can you tell me which ones you added back in? I can add them to v2 which I am working on now to add module ability back.

Quoted 3 lines

After I added them
back the agpgart driver appeared to load correctly. When I try to start X I get a black screen and have to shutdown and reboot to get video back.

Are you using DRI? I wasn't able to test with DRI, so that may not work correctly. I guess I should have said something about that :) Would it be possible for you to send some dmesg output. Maybe keep X from starting, get the output, and send it to me. Does 2.5 work in 8X mode for you?

Quoted 2 lines

This
is with an AIW 9700 Pro and a Gigabyte GA-7VAXP KT400 based motherboard .

Good I was hoping somebody with 8X hardware would try it out. BTW have you ever seen any other AIW cards before, I was curious if the new one looked any better or worse.

--Brian Jackson

Quoted 78 lines

- -- Edward Killips

- -----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Brian Jackson
Sent: Saturday, February 15, 2003 10:35 PM
To: [email protected]; [email protected]; [email protected]
Subject: 2.5 AGP for 2.4.21-pre4

This is a poor attempt at a backport of the 2.5.61 AGP subsystem by someone who doesn't know what he is doing and is in way over his head. That said, are
there any "brave" souls out there that want to try this out with an AGP3 card
and 2.4.21pre4. I compile/boot tested it with an old ati card, but I don't have an AGP 3.0 card/MB to test it on. I got into X and ran glxgears using this kernel(I am using it to finish writing this email)

http://www.mdrx.com/brian/2.4.21-pre4-2.5agp.diff.gz

caveats:
agp has to be built in to the kernel (no modules)

I did the following:
copied the drivers/char/agp directory from 2.5.61
copied include/asm-*/agp.h from 2.5.61
copied include/linux/*agp.h from 2.5.61
made some changes to drivers/char/agp/Makefile
on line 619&635 of frontend.c changed remap_page_range to only have 4
arguments
line 705 generic.c changed SetPageLocked -->SetPageReserved
(not sure if this is right, but Locked doesn't exist in 2.4 and I thought Reserved might work -- Let me know if this should be something else)
backend.c:241 & backend.c:263 commented references to 2.5 module stuff
(therefore this only safe to be built into the kernel for now, any ideas
what
I should use here instead?)
added some device id's to drivers/char/agp/agp.h from

	2.5.61/include/linux/pci_ids.h

uninclude gfp.h & linux/page-flags.h from amd-k7-agp.c

What else I need to do:
change to old style module init stuff

This is nowhere near suitable for production use, but I would like some people
that actually have AGP3 cards/MB's to try this out

- --Brian Jackson

P.S. All criticism is welcome even flaming since I am in a decent mood right now

P.S.S. To Dave Jones -- I thought 2.5 had support for VIA chipsets & AGP3, but
I only saw config options for the 7205/7505

- -
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0

iQA/AwUBPlDY2Xg7wzlNS3haEQLFswCfU0OJLlObv53E0kII4VpQJfQeDNEAoLSz 0h6O30p+lfi7kjuj28Mv6vpN
=kwgx
-----END PGP SIGNATURE-----

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#5 lore raw
In reply to Brian Jackson

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I tried the patch. The agpgart driver now loads and sets the apeture. When I try to start X the video does not initialize properly and I get a black screen. This is with an AIW Radeon 9700 Pro and a Gigabyte GA-7VAXP mother board with a KT400 chipset.

- -Edward Killips

- -----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Brian Jackson
Sent: Saturday, February 15, 2003 10:35 PM
To: [email protected]; [email protected]; [email protected]
Subject: 2.5 AGP for 2.4.21-pre4

This is a poor attempt at a backport of the 2.5.61 AGP subsystem by someone who doesn't know what he is doing and is in way over his head. That said, are
there any "brave" souls out there that want to try this out with an AGP3 card
and 2.4.21pre4. I compile/boot tested it with an old ati card, but I don't have an AGP 3.0 card/MB to test it on. I got into X and ran glxgears using this kernel(I am using it to finish writing this email)

http://www.mdrx.com/brian/2.4.21-pre4-2.5agp.diff.gz

caveats:
agp has to be built in to the kernel (no modules)

I did the following:
copied the drivers/char/agp directory from 2.5.61
copied include/asm-*/agp.h from 2.5.61
copied include/linux/*agp.h from 2.5.61
made some changes to drivers/char/agp/Makefile
on line 619&635 of frontend.c changed remap_page_range to only have 4
arguments
line 705 generic.c changed SetPageLocked -->SetPageReserved
(not sure if this is right, but Locked doesn't exist in 2.4 and I thought Reserved might work -- Let me know if this should be something else)
backend.c:241 & backend.c:263 commented references to 2.5 module stuff
(therefore this only safe to be built into the kernel for now, any ideas
what
I should use here instead?)
added some device id's to drivers/char/agp/agp.h from

	2.5.61/include/linux/pci_ids.h

uninclude gfp.h & linux/page-flags.h from amd-k7-agp.c

What else I need to do:
change to old style module init stuff

This is nowhere near suitable for production use, but I would like some people
that actually have AGP3 cards/MB's to try this out

- --Brian Jackson

P.S. All criticism is welcome even flaming since I am in a decent mood right now

P.S.S. To Dave Jones -- I thought 2.5 had support for VIA chipsets & AGP3, but
I only saw config options for the 7205/7505

- -
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0

iQA/AwUBPlL7D3g7wzlNS3haEQKPaQCcDuxCiquyCsxnEfnIQgva7bcVkvUAninG aD3lXYdNtjGeoI/JhHOUkYEc
=Eyaa
-----END PGP SIGNATURE-----