Bug in 2.5.62 kernel
it's about 2.5.62
I can do a make bzImage correctly
I can do a make modules correctly
but
when I do a make modules_install I get a lot of
depmod: Unresolved Symbols in /lib/modules/2.5.62/xxxx/xxxxx/xxxx.ko
What ca I do in order to see what's happening?
Thanks.
=============================================================
Luis Miguel Garcia Mancebo
Ingenieria Tecnica en Informatica de Gestion
Universidad de Deusto / University of Deusto
Bilbao / Spain
=============================================================
man depmod
depmod -e
depmod -ae
Cheers,
Dick Johnson
Penguin : Linux version 2.4.18 on an i686 machine (797.90 BogoMips). Why is the government concerned about the lunatic fringe? Think about it.
Quoted 11 lines · Luis Miguel Garcia
it's about 2.5.62
I can do a make bzImage correctly
I can do a make modules correctlybut
when I do a make
modules_installI get a lot of
depmod: Unresolved Symbols in/lib/modules/2.5.62/xxxx/xxxxx/xxxx.koWhat ca I do in order to see what's happening?
Do you have module-init-tools installed? Kernels since 2.5.48 require differed module utilities.
hello:
Yes, it was missing module-init-tools. Now I have my kernel compiled but when I try to boot, I can only see
Uncompressing Kernel... booting linux....
and then I cannot see nothing more but the HD is going up and down during half a minute, so I think something is happening but my screen is not updating.
What can I test in order to boot my system?
I'm behing a Sony Vaio N505-VE laptop.
Thanks.
Quoted 8 lines · On Tue, 18 Feb 2003 09:43:49 -0500 John Weber <[email protected]> wrote:
Quoted 7 lines · Luis Miguel Garcia
it's about 2.5.62
I can do a make bzImage correctly
I can do a make modules correctlybut
Quoted 11 lines
Quoted 4 lines
when I do a make
modules_installI get a lot of
depmod: Unresolved Symbols in/lib/modules/2.5.62/xxxx/xxxxx/xxxx.koWhat ca I do in order to see what's happening?
Do you have module-init-tools installed? Kernels since 2.5.48 require differed module utilities.
=============================================================
Luis Miguel Garcia Mancebo
Ingenieria Tecnica en Informatica de Gestion Universidad de Deusto / University of Deusto Bilbao / Spain
------------------------------------------------------------
there's no place that I could be without you there's no place that I could gleam without you there's no place that I could dream without you there's no place that I could be without you honestly
=============================================================
Quoted 7 lines · Luis Miguel Garcia
hello:
Yes, it was missing module-init-tools. Now I have my kernel compiled but when I try to boot, I can only see
Uncompressing Kernel... booting linux....
Quoted 7 lines
and then I cannot see nothing more but the HD is going up and down during half a minute, so I think something is happening but my screen is not updating.
What can I test in order to boot my system?
I'm behing a Sony Vaio N505-VE laptop.
Maybe the message below applies to you too.
Quoted 9 lines · Duncan Sands
This is becoming a FAQ! Did you enable the console in your .config?
CONFIG_VT=yCONFIG_VT_CONSOLE=y
Most likely you chose to compile the input system as a module, which caused the console options to be autohorribly deselected. Just say 'y' for the input subsystem, at which point the console options will reappear, letting you select them.
I hope this helps,
Duncan.
Signature · 1 line
GertJan