2.5.64 - cpu freq not turned on
There was a 2.5.x kernel that allowed me to use cpufreq with it but the recent ones just give me this message:
cpufreq: Intel(R) SpeedStep(TM) for this chipset not (yet) available.
Now I know it worked before cos I noticed it and played about with the 8 speed steps I had available to me (and I thought I only had 2).
What information is needed about my chipset to make the code detect it properly?
(not on cpufreq ml btw)
Signature · 5 lines
"Other countries of course, bear the same risk. But there's no doubt his
hatred is mainly directed at us. After all this is the guy who tried to
kill my dad."
- George W. Bush Jr, 'President' of the United States
September 26, 2002 (from a political fundraiser in Huston, Texas)Hi,
Quoted 7 lines · CaT
There was a 2.5.x kernel that allowed me to use cpufreq with it but the recent ones just give me this message:
cpufreq: Intel(R) SpeedStep(TM) for this chipset not (yet) available.
Now I know it worked before cos I noticed it and played about with the 8 speed steps I had available to me (and I thought I only had 2).
Actually, SpeedStep is (so far, Banias isn't out to the public market yet) only 2 states. What you had running was probably the p4-clockmod driver for Intel Pentium 4 processors. But that does only throttle the CPU, which causes (at best) linear energy saving while real "speedstep" is much better than that. You can see what cpufreq driver is loaded by cat'ting scaling_driver in the cpufreq sysfs directory for that cpu.
This directory moved in 2.5.64 - and that's why you probably think there was some regression (in fact, there is, but patches to fix that are on their way...) - the sysfs interface to cpufreq is now in/sys/devices/sys/cpu0/cpufreq/ or/sys/class/cpu/cpufreq/cpu0/cpufreq/
Quoted 2 lines
What information is needed about my chipset to make the code detect it properly?
lspci -- maybe it's a ich4-m southbridge, then the attached patch (also sent to Linus a few moments ago) might help.
Dominik
arch/i386/kernel/cpu/cpufreq/speedstep.c +15 -1
@@ -29,6 +29,9 @@#include <asm/msr.h> +#ifndef PCI_DEVICE_ID_INTEL_82801DB_12 +#define PCI_DEVICE_ID_INTEL_82801DB_12 0x24cc +#endif /* speedstep_chipset: * It is necessary to know which chipset is used. As accesses to
@@ -40,7 +43,7 @@#define SPEEDSTEP_CHIPSET_ICH2M 0x00000002#define SPEEDSTEP_CHIPSET_ICH3M 0x00000003 - +#define SPEEDSTEP_CHIPSET_ICH4M 0x00000004/* speedstep_processor */
@@ -106,6 +109,7 @@switch (speedstep_chipset) {case SPEEDSTEP_CHIPSET_ICH2M :case SPEEDSTEP_CHIPSET_ICH3M : +case SPEEDSTEP_CHIPSET_ICH4M :/* get PMBASE */ pci_read_config_dword (speedstep_chipset_dev,0x40 , &pmbase);if (!(pmbase &0x01 ))
@@ -166,6 +170,7 @@switch (speedstep_chipset) {case SPEEDSTEP_CHIPSET_ICH2M :case SPEEDSTEP_CHIPSET_ICH3M : +case SPEEDSTEP_CHIPSET_ICH4M :/* get PMBASE */ pci_read_config_dword (speedstep_chipset_dev,0x40 , &pmbase);if (!(pmbase &0x01 ))
@@ -245,6 +250,7 @@switch (speedstep_chipset) {case SPEEDSTEP_CHIPSET_ICH2M :case SPEEDSTEP_CHIPSET_ICH3M : +case SPEEDSTEP_CHIPSET_ICH4M : {u16 value =0 ;
@@ -277,6 +283,14 @@static unsigned int speedstep_detect_chipset (void ) { speedstep_chipset_dev =pci_find_subsys (PCI_VENDOR_ID_INTEL , +PCI_DEVICE_ID_INTEL_82801DB_12 , +PCI_ANY_ID , +PCI_ANY_ID , +NULL ); +if (speedstep_chipset_dev) +return SPEEDSTEP_CHIPSET_ICH4M ; + + speedstep_chipset_dev = pci_find_subsys(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, PCI_ANY_ID, PCI_ANY_ID,
Quoted 6 lines · Dominik Brodowski
Quoted 2 lines
Now I know it worked before cos I noticed it and played about with the 8 speed steps I had available to me (and I thought I only had 2).
Actually, SpeedStep is (so far, Banias isn't out to the public market yet) only 2 states. What you had running was probably the p4-clockmod driver for Intel Pentium 4 processors. But that does only throttle the CPU, which
Ahhh. I have a P3 though.
Quoted 3 lines
causes (at best) linear energy saving while real "speedstep" is much better than that. You can see what cpufreq driver is loaded by cat'ting
scaling_driverin the cpufreq sysfs directory for that cpu.
Not there.
Quoted 3 lines
This directory moved in 2.5.64 - and that's why you probably think there was some regression (in fact, there is, but patches to fix that are on their way...) - the sysfs interface to cpufreq is now in
2.5.63 doesn't turn speedstep on for me either.
Quoted 5 lines
Quoted 2 lines
What information is needed about my chipset to make the code detect it properly?
lspci -- maybe it's a ich4-m southbridge, then the attached patch (also sent to Linus a few moments ago) might help.
Didn't apply the patch cos I don't see that in the lspci output:
00:00.0 Host bridge: Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corp. 440BX/ZX - 82443BX/ZX AGP bridge (rev 03) 00:07.0 Bridge: Intel Corp. 82371AB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 03)
The rest are sound, cardbus etc.
Signature · 5 lines
"Other countries of course, bear the same risk. But there's no doubt his
hatred is mainly directed at us. After all this is the guy who tried to
kill my dad."
- George W. Bush Jr, 'President' of the United States
September 26, 2002 (from a political fundraiser in Huston, Texas)Quoted 9 lines · CaT
Didn't apply the patch cos I don't see that in the lspci output:
00:00.0 Host bridge: Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corp. 440BX/ZX - 82443BX/ZX AGP bridge (rev 03) 00:07.0 Bridge: Intel Corp. 82371AB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 03)
PIIX4EM southbridges are still in reverse-engeenering process.
Im also wondering why Intel still make this old stuff under NDA?
Cheers,
Signature · 3 lines
Ducrot Bruno http://www.poupinou.org Page profaissionelle http://toto.tu-me-saoules.com Haume page