Skip to contentSkip to conversation

Interrupt problem, no USB on SMP machine with 2.4.19/20/21

DISCUSSION Ed Wildgoose 3 participants 4 messages Mar 7, 2003

lore
Share & tools
lore
#0 lore raw

I am running a dual intel P3 933Mhz machine with an EPOX EP-D3VA motherboard. This has a via VT82C693A/694x [Apollo PRO133x] chipset

I cannot seem to get USB working at all on this machine. I have tried 2.4.19 20 and 21-ac (latest as of yesterday) with no luck. Basically doing insmod usb-uhci generates errors in the log:

Mar  7 19:09:07 [kernel] usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
Mar  7 19:09:07 [kernel] usb.c: new USB bus registered, assigned bus number 1
Mar  7 19:09:07 [kernel] hub.c: USB hub found
Mar  7 19:09:07 [kernel] usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Mar  7 19:09:08 [kernel] hub.c: new USB device 00:07.2-1, assigned address 2
Mar  7 19:09:10 [/etc/hotplug/usb.agent] Setup usbcore for USB product 0/0/0
Mar  7 19:09:11 [/etc/hotplug/usb.agent] Setup usbcore for USB product 0/0/0
Mar  7 19:09:13 [kernel] usb_control/bulk_msg: timeout
Mar  7 19:09:13 [kernel] usb.c: USB device not accepting new address=2 (error=-110)
Mar  7 19:09:13 [kernel] hub.c: new USB device 00:07.2-1, assigned address 3
Mar  7 19:09:18 [kernel] usb.c: USB device not accepting new address=3 (error=-110)

And this is consistent across kernel versions, usb-uhci and uhci give similar messages. This is using MPS 1.1 - with MPS 1.4 the IRQ is 19.

I'm assuming that the IRQ 9 is the problem and that the kernel is trying to assign IRQ 3? I tried:

    setpci -s 00:07.2 INTERRUPT_LINE=3

Results of lspci -vx -s 00:07.2 are:

00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 11) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
00: 06 11 38 30 07 00 10 02 11 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 04 00 00

But I'm not sure what I am expecting to happen...?

I'm not very experienced at this so hints on how to debug further would be appreciated (What other information do I need to send?)

Output from dmesg is below, note this is the 2.4.21ac kernel with ACPI - other tests were done without ACPI or any power management with similar results:

Thanks

Linux version 2.4.21-pre5-ac2 ([email protected]) (gcc version 3.2.2) #1 SMP Fri Mar 7 07:50:43 GMT 2003 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000f5a40
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #1 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Kernel command line: root=/dev/hda5
Initializing CPU#0
Detected 935.466 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1867.77 BogoMIPS
Memory: 514688k/524224k available (1607k kernel code, 9148k reserved, 572k data, 148k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.

CPU:     After generic, caps: 0383fbff 00000000 00000000 00000000
CPU:             Common caps: 0383fbff 00000000 00000000 00000000

Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#0.

CPU:     After generic, caps: 0383fbff 00000000 00000000 00000000
CPU:             Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 731.35 usecs.

task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1867.77 BogoMIPS
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check reporting enabled on CPU#1.

CPU:     After generic, caps: 0383fbff 00000000 00000000 00000000
CPU:             Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Coppermine) stepping 06

Total of 2 processors activated (3735.55 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011

.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011

.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:

00 000 00  1    0    0   0   0    0    0    00
01 0FF 0F  0    0    0   0   0    1    1    39
02 001 01  0    0    0   0   0    1    1    31
03 0FF 0F  0    0    0   0   0    1    1    41
04 0FF 0F  0    0    0   0   0    1    1    49
05 000 00  1    0    0   0   0    0    0    00
06 0FF 0F  0    0    0   0   0    1    1    51
07 0FF 0F  0    0    0   0   0    1    1    59
08 0FF 0F  0    0    0   0   0    1    1    61
09 000 00  1    0    0   0   0    0    0    00
0a 000 00  1    0    0   0   0    0    0    00
0b 000 00  1    0    0   0   0    0    0    00
0c 0FF 0F  0    0    0   0   0    1    1    69
0d 0FF 0F  0    0    0   0   0    1    1    71
0e 0FF 0F  0    0    0   0   0    1    1    79
0f 0FF 0F  0    0    0   0   0    1    1    81
10 0FF 0F  1    1    0   1   0    1    1    89
11 0FF 0F  1    1    0   1   0    1    1    91
12 0FF 0F  1    1    0   1   0    1    1    99
13 0FF 0F  1    1    0   1   0    1    1    A1
14 000 00  1    0    0   0   0    0    0    00
15 000 00  1    0    0   0   0    0    0    00
16 000 00  1    0    0   0   0    0    0    00
17 000 00  1    0    0   0   0    0    0    00

IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:17
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:19
IRQ10 -> 0:18
IRQ11 -> 0:16
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 935.4640 MHz.
..... host bus clock speed is 133.6376 MHz.
cpu: 0, clocks: 1336376, slice: 445458 CPU0<T0:1336368,T1:890896,D:14,S:445458,C:1336376>
cpu: 1, clocks: 1336376, slice: 445458 CPU1<T0:1336368,T1:445440,D:12,S:445458,C:1336376>
migration_task 0 on cpu=0
migration_task 1 on cpu=1
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/0596] at 00:07.0
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
tbxface-0099 [01] Acpi_load_tables : ACPI Tables successfully loaded
Parsing Methods:.................................................................................... 84 Control Methods found and parsed (341 nodes total)
ACPI Namespace successfully loaded at root c03943c0
ACPI: Core Subsystem version [20011018]
evxfevnt-0081 [-20] Acpi_enable : Transition to ACPI mode successful
Executing device _INI methods:...........................
27 Devices found: 27 _STA, 2 _INI
Completing Region and Field initialization:......................
16/20 Regions, 6/8 Fields initialized (341 nodes total)
ACPI: Subsystem enabled
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:pio
HPT370A: IDE controller at PCI slot 00:0b.0
HPT370A: chipset revision 4
HPT370A: not 100% native mode: will probe irqs later
HPT37X: using 33MHz PCI clock
ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hda: WDC WD1200JB-00CRA1, ATA DISK drive
blk: queue c03c2cc0, I/O limit 4095Mb (mask 0xffffffff)
hdc: RICOH DVD/CDRW MP9120, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=14593/255/63, UDMA(66) ide-floppy driver 0.99.newide
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
EXT2-fs warning (device ide0(3,5)): ext2_read_super: mounting ext3 filesystem as ext2

VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 148k freed
Adding Swap: 1044184k swap-space (priority -1)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0c.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xec00. Vers LK1.1.18-ac 00:10:4b:b4:be:e3, IRQ 10
product code 4e4b rev 00.9 date 06-19-98
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
Enabling bus-master transmits and whole-frame receives.
00:0c.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.104 loaded
bttv: using 32 buffers with 2080k (66560k total) for capture
bttv: Host bridge is VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x]
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 00:09.0, irq: 5, latency: 32, mmio: 0xdf001000
bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is 107d:6606
bttv0: using: BT878(Leadtek WinFast 2000/ W) [card=34,insmod option]
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
i2c-core.o: driver i2c TV tuner driver registered.
tuner: probing bt848 #0 i2c adapter [id=0x10005]
tuner: chip found @ 0xc2
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
i2c-core.o: client [Philips PAL_BG (FI1216 and compa] registered to adapter [bt848 #0](pos. 0).
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd8000000
[drm] AGP 0.99 on VIA Apollo Pro @ 0xd8000000 64MB
[drm] Initialized radeon 1.7.0 20020828 on minor 0
SCSI subsystem driver Revision: 1.00
hdc: attached ide-cdrom driver.
hdc: ATAPI 32X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
usb-uhci.c: $Revision: 1.275 $ time 08:29:13 Mar 7 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:07.2-1, assigned address 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device 00:07.2-1, assigned address 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
usb.c: USB disconnect on device 00:07.2-0 address 1
usb.c: USB bus 1 deregistered
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: new USB device 00:07.2-1, assigned address 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device 00:07.2-1, assigned address 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
usb.c: USB disconnect on device 00:07.2-0 address 1
usb.c: USB bus 1 deregistered
usb-uhci.c: $Revision: 1.275 $ time 08:29:13 Mar 7 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:07.2-1, assigned address 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device 00:07.2-1, assigned address 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)

#1 lore raw
Quoted 6 lines · Ed Wildgoose

I am running a dual intel P3 933Mhz machine with an EPOX EP-D3VA motherboard. This has a via VT82C693A/694x [Apollo PRO133x] chipset

I cannot seem to get USB working at all on this machine. I have tried 2.4.19 20 and 21-ac (latest as of yesterday) with no luck. Basically doing insmod usb-uhci generates errors in the log:

Have you booted with "noapic" on the command line? That's the only way a lot of VIA motherboards will get their onboard USB controller to work properly.

thanks,

greg k-h

#2 lore raw
Quoted 3 lines · Greg KH

Have you booted with "noapic" on the command line? That's the only way a lot of VIA motherboards will get their onboard USB controller to work properly.

VIA onboard devices require the interrupt line and pin are both written in APIC mode. Linux for reasons I still don't understand does not do that by default. The current -ac tree has a quirk for this although it doesnt seem to be working for all cases and needs a victim to review it more carefully

#3 lore raw
Quoted 9 lines · Greg KH
Quoted 3 lines

Have you booted with "noapic" on the command line? That's the only way a lot of VIA motherboards will get their onboard USB controller to work properly.

VIA onboard devices require the interrupt line and pin are both written in APIC mode. Linux for reasons I still don't understand does not do that by default. The current -ac tree has a quirk for this although it doesnt seem to be working for all cases and needs a victim to review it more carefully

booting my -ac kernel with noapic gets the USB working (hooray and thanks). I am just recompiling my gentoo-sources kernel to see if I can make that work (it certainly doesn't without ACPI enabled).

I will play with config files and kernel sources and see if I can determine whether anything *other* than the -ac branch will work correctly. Is there any way that I can usefully help feed that info back to the developers? Are there any tests that I can try?

Thanks for your help all