Skip to contentSkip to conversation

2.5 BK boot hang after ide

DISCUSSION Felipe Alfaro Solana 3 participants 5 messages Mar 23, 2003 – Mar 24, 2003

lore
Share & tools
lore
#0 lore raw

----- Original Message -----
From: Duncan Sands <[email protected]>
Date: Sun, 23 Mar 2003 14:44:21 +0100
To: [email protected]
Subject: 2.5 BK boot hang after ide

Quoted 12 lines

Copied down by hand:

...
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
VP_IDE: Chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt 8235 (rev 00) IDE UDMA 133 controller on pci00:11.1

	ide0: BM_DMA at 0xfc00-0xfc07, BIOS settings: hda: DMA, hdb: DMA 
	ide1: BM_DMA at 0xfc08-0xfc0f, BIOS settings: hdc: DMA, hdd: DMA 
Quoted 13 lines

hda: ST320423A, ATA DISK drive
hdb: Maxtor 6E030L0, ATA DISK drive
id0 at 0x1f0-0x1f7, 0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-MI402, ATAPI CD/DVD-ROM drive
hdd: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177, 0x376 on irq 15
hda: host protected area => 1
hda : 40011300 sectors (20486 MB) w/512KiB Cache, CHS=39693/16/63, UDMA(66)
hda: hda1 hda2 hda3
hdb: host protected area => 1
hdb : 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(133)
hdb: hdb1
(hangs)

I'm experiencing exactly the same as you: 2.5 won't continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 and 2.5.65-mm4. All of them fail at the same point. I've tried using ACPI, APM, disabling preempt, TCQ, enabling SysRq support, but had no luck.

The machine is a Pentium 4 2.0Gz, with a QDI PlatiniX 2D/533-A (i845E), 2 UDMA100 disks (Seagate ST380021A 80GB and IBM-DTLA-307030 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

Signature · 5 lines
______________________________________________
http://www.linuxmail.org/
Now with e-mail forwarding for only US$5.95/yr

Powered by Outblaze
#1 lore raw
Quoted 10 lines

I'm experiencing exactly the same as you: 2.5 won't continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 and 2.5.65-mm4. All of them fail at the same point. I've tried using ACPI, APM, disabling preempt, TCQ, enabling SysRq support, but had no luck.

The machine is a Pentium 4 2.0Gz, with a QDI PlatiniX 2D/533-A (i845E), 2 UDMA100 disks (Seagate ST380021A 80GB and IBM-DTLA-307030 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

2.5 BK worked for me two days ago, i.e. before Alan's latest IDE changes went in. Did any previous version work for you?

Duncan.

#2 lore raw
Quoted 12 lines · Duncan Sands
Quoted 10 lines

I'm experiencing exactly the same as you: 2.5 won't continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 and 2.5.65-mm4. All of them fail at the same point. I've tried using ACPI, APM, disabling preempt, TCQ, enabling SysRq support, but had no luck.

The machine is a Pentium 4 2.0Gz, with a QDI PlatiniX 2D/533-A (i845E), 2 UDMA100 disks (Seagate ST380021A 80GB and IBM-DTLA-307030 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

Quoted 4 lines

2.5 BK worked for me two days ago, i.e. before Alan's latest IDE changes went in. Did any previous version work for you?

I'm seeing the exact same behavior for AMD Opus. It just hangs after the hdd, no messages. I've been dropping printk's in random places, but still haven't figured it out.
Please see the "IDE Todo" thread for more info. Also, it
was working for me 2 days ago as well.

Cheers,
Nicholas

#3 lore raw
In reply to Felipe Alfaro Solana
Quoted 32 lines
Quoted 17 lines

Copied down by hand:

...
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
VP_IDE: Chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt 8235 (rev 00) IDE UDMA 133 controller on pci00:11.1 ide0: BM_DMA at 0xfc00-0xfc07, BIOS settings: hda: DMA, hdb:
DMA ide1: BM_DMA at 0xfc08-0xfc0f, BIOS settings: hdc: DMA, hdd: DMA hda:
ST320423A, ATA DISK drive
hdb: Maxtor 6E030L0, ATA DISK drive
id0 at 0x1f0-0x1f7, 0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-MI402, ATAPI CD/DVD-ROM drive
hdd: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive

Quoted 8 lines

ide1 at 0x170-0x177, 0x376 on irq 15
hda: host protected area => 1
hda : 40011300 sectors (20486 MB) w/512KiB Cache, CHS=39693/16/63, UDMA(66) hda: hda1 hda2 hda3
hdb: host protected area => 1
hdb : 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(133) hdb: hdb1
(hangs)

I'm experiencing exactly the same as you: 2.5 won't continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 and 2.5.65-mm4. All of them fail at the same point. I've tried using ACPI, APM, disabling preempt, TCQ, enabling SysRq support, but had no luck.

Quoted 4 lines

The machine is a Pentium 4 2.0Gz, with a QDI PlatiniX 2D/533-A (i845E), 2 UDMA100 disks (Seagate ST380021A 80GB and IBM-DTLA-307030 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

Seems to be OK with current BK.

Thanks,

Duncan.

#4 lore raw
Quoted 6 lines · Duncan Sands
Quoted 6 lines

I'm experiencing exactly the same as you: 2.5 won't continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 and 2.5.65-mm4. All of them fail at the same point. I've tried using ACPI, APM, disabling preempt, TCQ, enabling SysRq support, but had no luck.

Quoted 6 lines
Quoted 4 lines

The machine is a Pentium 4 2.0Gz, with a QDI PlatiniX 2D/533-A (i845E), 2 UDMA100 disks (Seagate ST380021A 80GB and IBM-DTLA-307030 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

Seems to be OK with current BK.

Yes, fortunately it's solved :-)

________________________________________________________________________
Felipe Alfaro Solana
Linux Registered User #287198
http://counter.li.org