aic7x^3: locks up (2.4.19 up to .21-pre7)

DISCUSSION Christian Vogel 1 participant 1 message Apr 18, 2003

Share & tools

Christian Vogel

author

2003-04-18 15:01 UTC #0 lore raw

Hi,

short version: I have two aic7xxx SCSI-controllers in my machine and I can reproduce hard lockups when accessing both simultaneously. This phenomenon was not present on 2.4.18 vanilla and appears since 2.4.19 up to (last one tested 2.4.21-pre7). 2.4.20-ac2 also is affected.

I have two aic7xxx controllers (one 2940U, one UW) on a VIA KT266-based motherboard with the following SCSI devices connected to them.

2940UW ----(internal 68pin)---- IBM DNES-318350W (Disk) on ID 0
|
+- (active terminator)

2940U ----(internal 50pin)---- PLEXTOR PX-20TS (CD) on ID 5

    |                         |
    +---  YAMAHA CRW4416S     +- ARCHIVE Python 27871-XXX (Streamer)
  (ext)    (CD-Writer)        |  
                              +- (passive terminator)

This setup seemed to be stable for a long time. Now I discovered (and verified) that I have problems with concurrent access between the 2940UW and the 2940U.

A test looks like this:

1.) boot acpi=off aic7xxx=verbose console=ttyS1 init=/bin/sh 2.) init-2.05a# /sbin/devfsd /dev
3.) init-2.05a# cat /dev/scsi/host1/bus0/target6/lun0/cd >/dev/null & 4.) init-2.05a# ls /bin
(hearing harddisk clicking a little...)
---> tadaa: instant hang. No response whatsoever, cursor of the
matrox framebuffer stops blinking

It's also possible to try burning a CD, this also locks the machine (and that's how I discovered it, who needs CDs anyway these days :-) ).

Permutations I have tested:

  -  acpi=off/on
  -  internal/external cable of the 2940U connected/disconnected
  -  reading Plextor/Yamaha

Affected kernels:
- kernel 2.4.18 works without any problems
- kernel 2.4.19, 20, 21-pre7, 20-ac2 hangs

I don't think that cabling of the SCSI-bus is an issue, because the problem appears on both the internal and the external bus independently and it always appears as soon as I access the *other* SCSI adapter.... And using 2.4.18 I burned many CDs flawlessly...

/proc/interrupts:

  0:       6647          XT-PIC  timer
  1:        135          XT-PIC  keyboard
  2:          0          XT-PIC  cascade
  4:          1          XT-PIC  serial
  8:          1          XT-PIC  rtc
 11:       3311          XT-PIC  aic7xxx, VIA8233
 12:       1084          XT-PIC  PS/2 Mouse
 14:         17          XT-PIC  ide0
 15:       1114          XT-PIC  aic7xxx, eth0, Ensoniq AudioPCI, usb-uhci
NMI:          0 
LOC:       6613 
ERR:         10
MIS:          0

Attachments (too long to have inline conveniently):

- 2.4.21-p7-no_acpi.txt -> sample boot. 2.4.21-p7 with acpi patch but acpi disabled

- lspci -> output of lspci -v -v -v

- config-2.4.21... -> .config from 2.4.21-p7 kernel used

If I can help with providing some more datapoints, feel free to email me.

Chris

Signature · 1 line

Gates' Law: Every 18 months, the speed of software halfes.

Linux version 2.4.21-pre7-acpi ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-113)) #2 Thu Apr 17 20:27:23 CEST 2003 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: ro root=/dev/sda3 video=matrox:vesa:0x194,font:SUN12x22 aic7xxx=verbose console=ttyS1,9600 init=/bin/sh acpi=off Found and enabled local APIC!
Initializing CPU#0
Detected 1000.063 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1992.29 BogoMIPS
Memory: 256752k/262080k available (1244k kernel code, 4940k reserved, 353k data, 264k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Duron(tm) processor stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1000.0139 MHz.
..... host bus clock speed is 200.0027 MHz.
cpu: 0, clocks: 2000027, slice: 1000013
CPU0<T0:2000016,T1:1000000,D:3,S:1000013,C:2000027>
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030328
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xfb430, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3099] at 00:00.0
KT266 enable bus disconnect on STPGNT: Now Active!
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
matroxfb: Matrox MGA-G200 (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 1152x864x24bpp (virtual: 1152x2426)
matroxfb: framebuffer at 0xE7000000, mapped to 0xd0805000, size 8388608
Console: switching to colour frame buffer device 96x39
fb0: MATROX VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1

    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio

hda: Pioneer DVD-ROM ATAPIModel DVD-115 0127, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
SCSI subsystem driver Revision: 1.00
ahc_pci:0:14:0: Reading SEEPROM...done.
ahc_pci:0:14:0: Low byte termination Enabled
ahc_pci:0:14:0: Downloading Sequencer Program... 441 instructions downloaded ahc_pci:0:14:0: Features 0x0, Bugs 0x25, Flags 0x10401540 ahc_pci:0:15:0: Reading SEEPROM...done.
ahc_pci:0:15:0: internal 50 cable not present, internal 68 cable is present ahc_pci:0:15:0: external cable not present
ahc_pci:0:15:0: BIOS eeprom is present
ahc_pci:0:15:0: High byte termination Enabled
ahc_pci:0:15:0: Low byte termination Enabled
ahc_pci:0:15:0: Downloading Sequencer Program... 451 instructions downloaded ahc_pci:0:15:0: Features 0x5, Bugs 0x25, Flags 0x10481400 (scsi0:A:0:0): Sending WDTR 0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.28
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs

(scsi0:A:0:0): Received WDTR 0 filtered to 0 (scsi0:A:0): 3.300MB/s transfers
scsi0: target 0 using 8bit transfers
(scsi0:A:0): 3.300MB/s transfers
scsi0: target 0 using asynchronous transfers
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.28
<Adaptec 2940 SCSI adapter>
aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs

(scsi0:A:0:0): Sending WDTR 1
(scsi0:A:0:0): Received WDTR 1 filtered to 1
(scsi0:A:0): 6.600MB/s transfers (16bit)
scsi0: target 0 using 16bit transfers
(scsi0:A:0:0): Sending SDTR period c, offset 8
spurious 8259A interrupt: IRQ7.
(scsi0:A:0:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
scsi0: target 0 synchronous at 20.0MHz, offset = 0x8
Vendor: IBM Model: DNES-318350W Rev: S80K
Type: Direct-Access ANSI SCSI revision: 03
(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit) scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Vendor: YAMAHA Model: CRW4416S Rev: 1.0f
Type: CD-ROM ANSI SCSI revision: 02
(scsi1:A:6:0): Sending SDTR period 19, offset f (scsi1:A:6:0): Received SDTR period 1e, offset f
Filtered to period 1e, offset f
(scsi1:A:6): 8.333MB/s transfers (8.333MHz, offset 15)
scsi1: target 6 synchronous at 8.0MHz, offset = 0xf (scsi1:A:6): 8.333MB/s transfers (8.333MHz, offset 15) Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 (scsi0:A:0:0): Sending WDTR 1
(scsi0:A:0:0): Received WDTR 1 filtered to 1
(scsi0:A:0): 6.600MB/s transfers (16bit)
scsi0: target 0 using asynchronous transfers (scsi0:A:0:0): Sending SDTR period c, offset 8 (scsi0:A:0:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
scsi0: target 0 synchronous at 20.0MHz, offset = 0x8
SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB) Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1 p3 p4 < p5 p6 p7 p8 >
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 264k freed
init-2.05a# /sbin/devfsd /dev
Started device management daemon v1.3.25 for /dev init-2.05a# cat /dev/scsi/host1/bus0/target6/lun0/cd >/dev/null &
[1] 14
init-2.05a# Attached scsi CD-ROM sr0 at scsi1, channel 0, id 6, lun 0
sr0: scsi3-mmc drive: 16x/16x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12

init-2.05a#
init-2.05a#
init-2.05a#
init-2.05a#
init-2.05a#
init-2.05a# ls -l /bin

00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Subsystem: VIA Technologies, Inc. VT8367 [KT266]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT333 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e4000000-e6ffffff
Prefetchable memory behind bridge: e7000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05)
Subsystem: Compaq Computer Corporation NC3121 Fast Ethernet NIC (WOL)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: Memory at e9100000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at c000 [size=32]
Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at c400 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0e.0 SCSI storage controller: Adaptec AHA-2940/2940W / AIC-7871 (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at c800 [disabled] [size=256]
Region 1: Memory at e9101000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]

00:0f.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at cc00 [disabled] [size=256]
Region 1: Memory at e9102000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]

00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 15
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 15
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 30)
Subsystem: VIA Technologies, Inc.: Unknown device 4511
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at e000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. MGA-G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: Memory at e7000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at e4000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1

#
# Automatically generated by make menuconfig: don't edit #
CONFIG_X86=y
# CONFIG_SBUS is not set
CONFIG_UID16=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y

#
# Loadable module support
#
CONFIG_MODULES=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y

#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_HAS_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_F00F_WORKS_OK=y
CONFIG_X86_MCE=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_HIGHMEM is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_SMP is not set
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_TSC_DISABLE is not set
CONFIG_X86_TSC=y

#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_HOTPLUG is not set
# CONFIG_PCMCIA is not set
# CONFIG_HOTPLUG_PCI is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_PM=y
# CONFIG_APM is not set

#
# ACPI Support
#
CONFIG_ACPI=y
# CONFIG_ACPI_HT_ONLY is not set
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_DEBUG is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
CONFIG_PARPORT_OTHER=y
CONFIG_PARPORT_1284=y

#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=m
CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_BLK_STATS is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
# CONFIG_NETFILTER is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
# CONFIG_NET_IPGRE_BROADCAST is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_INET_ECN=y
# CONFIG_SYN_COOKIES is not set
CONFIG_IPV6=m
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
CONFIG_VLAN_8021Q=m
# CONFIG_IPX is not set
# CONFIG_ATALK is not set

#
# Appletalk devices
#
# CONFIG_DEV_APPLETALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Network testing
#
CONFIG_NET_PKTGEN=m

#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set

#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y

#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=m
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_BLK_DEV_GENERIC is not set
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set

#
# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_DEBUG_QUEUES=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set

#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set

#
# Network device support
#
CONFIG_NETDEVICES=y

#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
CONFIG_ETHERTAP=m

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
CONFIG_EEPRO100=m
# CONFIG_EEPRO100_PIO is not set
# CONFIG_E100 is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_SUNDANCE_MMIO is not set
# CONFIG_TLAN is not set
# CONFIG_TC35815 is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set

#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set

#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Input core support
#
CONFIG_INPUT=y
CONFIG_INPUT_KEYBDEV=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=y
CONFIG_INPUT_EVDEV=y

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=m
# CONFIG_TIPAR is not set

#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_PHILIPSPAR is not set
# CONFIG_I2C_ELV is not set
# CONFIG_I2C_VELLEMAN is not set
# CONFIG_SCx200_I2C is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_ALGOPCF is not set
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_PROC=m

#
# Mice
#
# CONFIG_BUSMOUSE is not set
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
# CONFIG_MK712_MOUSE is not set

#
# Joysticks
#
CONFIG_INPUT_GAMEPORT=y
CONFIG_INPUT_NS558=m
# CONFIG_INPUT_LIGHTNING is not set
# CONFIG_INPUT_PCIGAME is not set
# CONFIG_INPUT_CS461X is not set
# CONFIG_INPUT_EMU10K1 is not set
CONFIG_INPUT_SERIO=m
# CONFIG_INPUT_SERPORT is not set
# CONFIG_INPUT_ANALOG is not set
# CONFIG_INPUT_A3D is not set
# CONFIG_INPUT_ADI is not set
# CONFIG_INPUT_COBRA is not set
# CONFIG_INPUT_GF2K is not set
# CONFIG_INPUT_GRIP is not set
# CONFIG_INPUT_INTERACT is not set
# CONFIG_INPUT_TMDC is not set
# CONFIG_INPUT_SIDEWINDER is not set
# CONFIG_INPUT_IFORCE_USB is not set
# CONFIG_INPUT_IFORCE_232 is not set
# CONFIG_INPUT_WARRIOR is not set
# CONFIG_INPUT_MAGELLAN is not set
# CONFIG_INPUT_SPACEORB is not set
# CONFIG_INPUT_SPACEBALL is not set
# CONFIG_INPUT_STINGER is not set
# CONFIG_INPUT_DB9 is not set
# CONFIG_INPUT_GAMECON is not set
# CONFIG_INPUT_TURBOGRAFX is not set
# CONFIG_QIC02_TAPE is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_IPMI_PANIC_EVENT is not set
# CONFIG_IPMI_DEVICE_INTERFACE is not set
# CONFIG_IPMI_KCS is not set
# CONFIG_IPMI_WATCHDOG is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_SCx200_GPIO is not set
# CONFIG_AMD_RNG is not set
# CONFIG_INTEL_RNG is not set
# CONFIG_AMD_PM768 is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=m
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_I810 is not set
CONFIG_AGP_VIA=y
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD_8151 is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
CONFIG_DRM=y
# CONFIG_DRM_OLD is not set
CONFIG_DRM_NEW=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I810_XFREE_41 is not set
# CONFIG_DRM_I830 is not set
CONFIG_DRM_MGA=m
# CONFIG_DRM_SIS is not set
# CONFIG_MWAVE is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=m
# CONFIG_REISERFS_FS is not set
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=m
# CONFIG_MSDOS_FS is not set
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
# CONFIG_JFS_FS is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_MINIX_FS=m
# CONFIG_VXFS_FS is not set
CONFIG_NTFS_FS=m
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
CONFIG_UDF_FS=m
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set

#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_TCP is not set
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
# CONFIG_ZISOFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y

#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set

#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set

#
# Frame-buffer support
#
CONFIG_FB=y
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_CLGEN is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_VESA is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_HGA is not set
CONFIG_VIDEO_SELECT=y
CONFIG_FB_MATROX=y
# CONFIG_FB_MATROX_MILLENIUM is not set
# CONFIG_FB_MATROX_MYSTIQUE is not set
# CONFIG_FB_MATROX_G450 is not set
CONFIG_FB_MATROX_G100A=y
CONFIG_FB_MATROX_G100=y
CONFIG_FB_MATROX_I2C=m
# CONFIG_FB_MATROX_MAVEN is not set
CONFIG_FB_MATROX_PROC=m
# CONFIG_FB_MATROX_MULTIHEAD is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set
CONFIG_FBCON_ADVANCED=y
# CONFIG_FBCON_MFB is not set
# CONFIG_FBCON_CFB2 is not set
# CONFIG_FBCON_CFB4 is not set
CONFIG_FBCON_CFB8=y
CONFIG_FBCON_CFB16=y
CONFIG_FBCON_CFB24=y
CONFIG_FBCON_CFB32=y
# CONFIG_FBCON_AFB is not set
# CONFIG_FBCON_ILBM is not set
# CONFIG_FBCON_IPLAN2P2 is not set
# CONFIG_FBCON_IPLAN2P4 is not set
# CONFIG_FBCON_IPLAN2P8 is not set
# CONFIG_FBCON_MAC is not set
# CONFIG_FBCON_VGA_PLANES is not set
# CONFIG_FBCON_VGA is not set
# CONFIG_FBCON_HGA is not set
# CONFIG_FBCON_FONTWIDTH8_ONLY is not set
CONFIG_FBCON_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_SUN8x16 is not set
CONFIG_FONT_SUN12x22=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set

#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_ALI5455 is not set
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_MIDI_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_FORTE is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_MIDI_VIA82CXXX is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
# CONFIG_SOUND_AD1816 is not set
# CONFIG_SOUND_AD1889 is not set
# CONFIG_SOUND_SGALAXY is not set
# CONFIG_SOUND_ADLIB is not set
# CONFIG_SOUND_ACI_MIXER is not set
# CONFIG_SOUND_CS4232 is not set
# CONFIG_SOUND_SSCAPE is not set
# CONFIG_SOUND_GUS is not set
# CONFIG_SOUND_VMIDI is not set
# CONFIG_SOUND_TRIX is not set
# CONFIG_SOUND_MSS is not set
# CONFIG_SOUND_MPU401 is not set
# CONFIG_SOUND_NM256 is not set
# CONFIG_SOUND_MAD16 is not set
# CONFIG_SOUND_PAS is not set
# CONFIG_PAS_JOYSTICK is not set
# CONFIG_SOUND_PSS is not set
# CONFIG_SOUND_SB is not set
# CONFIG_SOUND_AWE32_SYNTH is not set
# CONFIG_SOUND_KAHLUA is not set
# CONFIG_SOUND_WAVEFRONT is not set
# CONFIG_SOUND_MAUI is not set
# CONFIG_SOUND_YM3812 is not set
# CONFIG_SOUND_OPL3SA1 is not set
# CONFIG_SOUND_OPL3SA2 is not set
# CONFIG_SOUND_YMFPCI is not set
# CONFIG_SOUND_YMFPCI_LEGACY is not set
# CONFIG_SOUND_UART6850 is not set
# CONFIG_SOUND_AEDSP16 is not set
# CONFIG_SOUND_TVMIXER is not set

#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_UHCI=m
# CONFIG_USB_UHCI_ALT is not set
# CONFIG_USB_OHCI is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_BLUETOOTH is not set
# CONFIG_USB_MIDI is not set
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
CONFIG_USB_STORAGE_DPCM=y
# CONFIG_USB_STORAGE_HP8200e is not set
CONFIG_USB_STORAGE_SDDR09=y
# CONFIG_USB_STORAGE_SDDR55 is not set
CONFIG_USB_STORAGE_JUMPSHOT=y
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_HID is not set
# CONFIG_USB_HIDINPUT is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
CONFIG_USB_DC2XX=m
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
# CONFIG_USB_SERIAL_DEBUG is not set
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
# CONFIG_USB_SERIAL_KEYSPAN_MPR is not set
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
# CONFIG_USB_SERIAL_KEYSPAN_USA49WLC is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_CYBERJACK is not set
CONFIG_USB_SERIAL_XIRCOM=m
# CONFIG_USB_SERIAL_OMNINET is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set

#
# Bluetooth support
#
# CONFIG_BLUEZ is not set

#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_IOVIRT is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_FRAME_POINTER is not set

#
# Library routines
#
# CONFIG_ZLIB_INFLATE is not set
# CONFIG_ZLIB_DEFLATE is not set