Shared Interrupts Question (2.4)
I am trying to understand "kinda shared" interrupts.
There are various interrupts in my not-yet-released CPU, and I have interrupt code that knows how to talk to them. So far so good. I also have an external interrupt controller that groups together 18 external interrupt sources and sends them in one CPU pin. This external controller has a register for enabling interrupts, and a register for status/acknowledge. Pretty standard.
The CPU code doesn't know about the external controller. It seems silly to rewrite the CPU-specific interrput code to accommodate this board-specific detail (besides then my code won't match Dale's). So I figure I tell the kernel I am doing shared interrupts.
So where do I enable, disable, and acknowledge these external bits? Specifically, I am trying to get a couple of serial ports working. I can put conditional code in serial.c startup() to enable these interrupts, but how do I know which serial port? Add a conditionally compiled sub-IRQ number to serial_state structure?
Is there a cleaner way?
Thanks,
-kb
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi
U r saying from the interrupt controller only one physical line is coming to CPU to interrupt CPU.
SO in the do_irq routine u will have to read the interrupt controller registers & find out who has caused the interrupt & then invoke interrupt handler corressponding to the interrupt number.
U should have a way, from the CPU to read the interrupt controller registers & find out the cause.....................
Bhupi
Linux+Hypertransport -->Silicon
www.gdatech.com
Good after beer -- Linux
Quoted 34 lines · --- Kent Borg
I am trying to understand "kinda shared" interrupts.
There are various interrupts in my not-yet-released CPU, and I have
interrupt code that knows how to talk to them. So far so good. I
also have an external interrupt controller that groups together 18
external interrupt sources and sends them in one CPU pin. This
external controller has a register for enabling interrupts, and a
register for status/acknowledge. Pretty standard.The CPU code doesn't know about the external controller. It seems
silly to rewrite the CPU-specific interrput code to accommodate this
board-specific detail (besides then my code won't match Dale's). So I
figure I tell the kernel I am doing shared interrupts.So where do I enable, disable, and acknowledge these external bits?
Specifically, I am trying to get a couple of serial ports working. I
can put conditional code inserial.cstartup()to enable these
interrupts, but how do I know which serial port? Add a conditionally
compiled sub-IRQ number toserial_statestructure?
Quoted 9 lines
Is there a cleaner way?
Thanks,
-kb
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Quoted 4 lines · bhupinder sahran
SO in the
do_irqroutine u will have to read the interrupt controller registers & find out who has caused the interrupt & then invoke interrupt handler corressponding to the interrupt number.
Yes, but how do I enable the interrupt in the first place? (Disable too.) I mean, I know how to set the bit, but where is the best place to do so? In the case of a serial port, I figure I could turn it on in startup() in serial.c. But then how do I know which of two possible interrupts it is? I could do something hacky, like look at the UART address and infer from there, but that looks nasty...
Thanks,
-kb, the Kent who, if has to muck with existing kernel files, wants to do so in an acceptable way.
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Quoted 15 lines · Kent Borg
I am trying to understand "kinda shared" interrupts.
There are various interrupts in my not-yet-released CPU, and I have interrupt code that knows how to talk to them. So far so good. I also have an external interrupt controller that groups together 18 external interrupt sources and sends them in one CPU pin. This external controller has a register for enabling interrupts, and a register for status/acknowledge. Pretty standard.
The CPU code doesn't know about the external controller. It seems silly to rewrite the CPU-specific interrput code to accommodate this board-specific detail (besides then my code won't match Dale's). So I figure I tell the kernel I am doing shared interrupts.
Quoted 7 lines
So where do I enable, disable, and acknowledge these external bits? Specifically, I am trying to get a couple of serial ports working. I can put conditional code in
serial.cstartup()to enable these interrupts, but how do I know which serial port? Add a conditionally compiled sub-IRQ number toserial_statestructure?Is there a cleaner way?
Create and register a board-specific interrupt driver. Assign it a range of irqs (non-conflicting with the main interrupt driver). When called with an irq outside its range, the board-specific driver routines forward the call to the main driver. The board-specific driver does a request_irq at init time for the one main irq it is multiplexing.
-Dale
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Quoted 4 lines · Dale Farnsworth
Create and register a board-specific interrupt driver. Assign it a range of irqs (non-conflicting with the main interrupt driver). When called with an irq outside its range, the board-specific driver routines forward the call to the main driver.
Cool, cool...
Quoted 2 lines
The board-specific driver does a
request_irqat init time for the one main irq it is multiplexing.
What does my handler on the main irq do? Perhaps nothing?
I am figuring I supply my own get_irq call, and it returns one of this new interrupt range, or if none, calls the previous get_irq. If I never let the main irq number come back, my handler on the main irq never gets called, right? If so, why am calling request_irq in the first place? To keep the system from puking on spurious interrupts? (But if I answer the get_irq, and if I never answer the main irq number, how would it know?)
Thanks,
-kb, the Kent who thinks he is getting close.
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Quoted 6 lines · Kent Borg
Quoted 4 lines · Dale Farnsworth
Create and register a board-specific interrupt driver. Assign it a range of irqs (non-conflicting with the main interrupt driver). When called with an irq outside its range, the board-specific driver routines forward the call to the main driver.
Quoted 6 lines
Cool, cool...
Quoted 2 lines
The board-specific driver does a
request_irqat init time for the one main irq it is multiplexing.What does my handler on the main irq do? Perhaps nothing?
Nothing. You make sure that get_irq never returns that irq, so the handler won't be called.
Quoted 5 lines
I am figuring I supply my own
get_irqcall, and it returns one of this new interrupt range, or if none, calls the previousget_irq. If I never let the main irq number come back, my handler on the main irq never gets called, right? If so, why am callingrequest_irqin the first place?
To enable (unmask) the main irq. I think you're right, it's better to not call request_irq and just enable the irq directly.
Quoted 3 lines
To keep the system from puking on spurious interrupts? (But if I answer the
get_irq, and if I never answer the main irq number, how would it know?)
I'd call the main get_irq before checking for interrupt in my range.
my_get_irq() {
int irq = main_get_irq();
if (irq != my_irq)
return irq;
/* find which irq in my range cascaded into my_irq */
irq = find_cascaded_irq();
return irq;
}-Dale
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/