lilo and 2.5.69?
Hello,
Normally I have in my lili.conf:
append = "root=/dev/scsi/host0/bus0/target15/lun0/part2 video=matrox:1600x1200-16@75"
But I got:
Fatal: open /dev/ide/host0/bus0/target0/lun0/par: No such file or directory
Exit 1
Same if I put:
root=/dev/scsi/host0/bus0/target15/lun0/part2
Or root=/dev/sdb2
Is there something special to do with this new kernel?
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
Quoted 1 line · Gregoire Favre
Is there something special to do with this new kernel?
You need to fix lilo to not assume the names listet in /proc/partitions are actual device files. In 2.5.69 there's a bug that it prints truncated devfs names instead of traditional device names as it should, but relying on the names to mean anything is broken - that kernel can't enforce the device names used.
The following patch that is in Linus BK tree should get it working for you again for now..
fs/partitions/check.c +0 -13
@@ -96,19 +96,6 @@char *disk_name (struct gendisk *hd,int part,char *buf) { -#ifdef CONFIG_DEVFS_FS -if (hd->devfs_name[0 ] !='\0' ) { -if (part) -snprintf (buf,BDEVNAME_SIZE ,"%s/part%d" , - hd->devfs_name, part); -else if (hd->minors !=1 ) -snprintf (buf,BDEVNAME_SIZE ,"%s/disc" , hd->devfs_name); -else -snprintf (buf,BDEVNAME_SIZE ,"%s" , hd->devfs_name); -return buf; - } -#endif -if (!part)snprintf (buf,BDEVNAME_SIZE ,"%s" , hd->disk_name);else if (isdigit (hd->disk_name[strlen (hd->disk_name)-1 ]))
Quoted 12 lines · Gregoire Favre
Hello,
Normally I have in my lili.conf:
append = "root=/dev/scsi/host0/bus0/target15/lun0/part2 video=matrox:1600x1200-16@75"
But I got:
Fatal: open
/dev/ide/host0/bus0/target0/lun0/par: No such file or directory
Exit 1
Quoted 6 lines
Same if I put:
root=/dev/scsi/host0/bus0/target15/lun0/part2Or root=/dev/sdb2
Is there something special to do with this new kernel?
Looks like a bug that truncates long device names. Looks like your'e using devfs, using /dev/discs/discX/part2
is a fine workaround - because it is short enough. Replace the X with whatever number your host0-target15 disk has.
Helge Hafting
Quoted 6 lines · Helge Hafting
Looks like a bug that truncates long device names. Looks like your'e using devfs, using
/dev/discs/discX/part2
is a fine workaround - because it is short enough. Replace the X with whatever number your host0-target15 disk has.
I have put:
append = "root=/dev/discs/disc2/part2 video=matrox:1600x1200-16@75"
And it produces the same error:
Fatal: open /dev/ide/host0/bus0/target0/lun0/par: No such file or directory 8,1 Top
Exit 1
which was previsible as dev/sdb2 produced the same problem.
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]