[2.4.21] orinoco_cs card reinsertion
PATCH 1/1 [2.4.21] orinoco_cs card reinsertion
Hello!
After switching from 2.4.20 to 2.4.21 (Debian unstable package kernel-source-2.4.21-5), my wireless LAN PCMCIA card stopped working when I hot-removed and reinserted it. I got these messages in /var/log/syslog, plus a high beep on removal and a high and then a low beep on reinsertion:
Upon removal:
Aug 29 16:00:41 SebastianL2 kernel: orinoco_lock() called with
hw_unavailable (dev=cf34b800)
Upon reinsertion:
Aug 29 16:00:44 SebastianL2 cardmgr[192]: socket 0: ZCOMAX AirRunner/XI-300 Aug 29 16:00:44 SebastianL2 kernel: GetNextTuple(). No matching CIS configuration, maybe you need the ignore_cis_vcc=1 parameter. Aug 29 16:00:44 SebastianL2 kernel: orinoco_cs: GetFirstTuple: No more items Aug 29 16:00:45 SebastianL2 cardmgr[192]: get dev info on socket 0
failed: Resource temporarily unavailable
I looked at the changes between the two kernels, in orinoco.c, orinoco_cs.c, and hermes.c, and it seems that quite a bit of code was restructured. So unfortunately, I cannot narrow it down to a single change that caused this. The attached patch fixes the problem for me, but it is NOT a simple copy from the old driver, and it may not be correct at all. However, it might give someone a hint about what went wrong. Anyway, even with this patch, I still get the "orinoco_lock() called with hw_unavailable" message when I remove the card.
Sorry if I'm posting a patch for a problem that has already been fixed in 2.4.22. The Debian package is still at 2.4.21, and I don't know anything about the Debian patches and why they are needed, etc. If I can just install a kernel from kernel.org, I will do this, and try to see if the problem is still there (I can see an item "orinoco driver update" in the changelog, but it's not specific). Should I also install a 2.6 kernel and check?
I have attached the output of lspci -vvv and the parts of the syslog that identify my card and show the problem. The controller is this entry in lspci.txt:
00:08.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
Here is the output of ver_linux:
------------------------------------------------------------------------
Linux SebastianL2 2.4.21 #1 Sat Aug 30 00:22:04 CEST 2003 i686 GNU/Linux
Gnu C 3.3.2 Gnu make 3.80 binutils 2.14.90.0.5 util-linux 2.11z mount 2.11z modutils 0.9.13 e2fsprogs 1.35-WIP pcmcia-cs 3.2.2 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 3.1.11 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 5.0.90
------------------------------------------------------------------------
Hopefully someone can find the true cause of the problem. Good luck.
Signature · 1 line
Sebastian Reichelt
net/wireless/orinoco_cs.c renamed from net/wireless/orinoco_cs.c.orig +2 -2
@@ -597,8 +597,8 @@orinoco_unlock (priv, &flags); -/* if (link->open) */ -/* orinoco_cs_stop(dev); */ +if (dev->stop) + dev->stop (dev);mod_timer (&link->release, jiffies +HZ /20 ); }
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 80)
Subsystem: Uniwill Computer Corp: Unknown device 8100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dfd00000-dfefffff
Prefetchable memory behind bridge: cfb00000-dfbfffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
Subsystem: Uniwill Computer Corp: Unknown device 3000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 9 Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 10400000-107ff000 (prefetchable) Memory window 1: 10800000-10bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
00:10.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: Unknown device 8415:8200
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at dffff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10)
Subsystem: Uniwill Computer Corp: Unknown device 8100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Uniwill Computer Corp: Unknown device 8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1e) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1e) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
Subsystem: Uniwill Computer Corp: Unknown device 8235
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40)
Subsystem: Uniwill Computer Corp: Unknown device 8100
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at e400 [size=256]
Region 1: I/O ports at e000 [size=4]
Region 2: I/O ports at dc00 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 20)
Subsystem: Uniwill Computer Corp: Unknown device 4005
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at e800 [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51)
Subsystem: Uniwill Computer Corp: Unknown device 8100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at dffff700 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: S3 Inc. VT8636A [ProSavage KN133] AGP4X VGA Controller (TwisterK) (rev 01) (prog-if 00 [VGA])
Subsystem: Uniwill Computer Corp: Unknown device 8003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (1000ns min, 63750ns max), cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at dfe80000 (32-bit, non-prefetchable) [size=512K] Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at dfe70000 [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Aug 29 15:58:07 SebastianL2 kernel: Linux Kernel Card Services 3.1.22 Aug 29 15:58:07 SebastianL2 kernel: options: [pci] [cardbus] [pm] Aug 29 15:58:07 SebastianL2 kernel: PCI: Assigned IRQ 9 for device 00:08.0 Aug 29 15:58:07 SebastianL2 kernel: orinoco.c 0.13b (David Gibson <[email protected]> and others) Aug 29 15:58:07 SebastianL2 kernel: hermes.c: 4 Dec 2002 David Gibson <[email protected]> Aug 29 15:58:07 SebastianL2 kernel: orinoco_cs.c 0.13b (David Gibson <[email protected]> and others) Aug 29 15:58:07 SebastianL2 kernel: NET4: Linux TCP/IP 1.0 for NET4.0 Aug 29 15:58:07 SebastianL2 kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes Aug 29 15:58:07 SebastianL2 kernel: TCP: Hash tables configured (established 16384 bind 32768) Aug 29 15:58:07 SebastianL2 kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Aug 29 15:58:07 SebastianL2 kernel: Yenta IRQ list 0820, PCI irq9 Aug 29 15:58:07 SebastianL2 kernel: Socket status: 30000411 Aug 29 15:58:07 SebastianL2 kernel: VFS: Mounted root (ext2 filesystem) readonly. Aug 29 15:58:07 SebastianL2 kernel: Freeing unused kernel memory: 76k freed Aug 29 15:58:07 SebastianL2 kernel: Adding Swap: 248968k swap-space (priority -1) Aug 29 15:58:07 SebastianL2 cardmgr[191]: cannot access /lib/modules/2.4.21: No such file or directory Aug 29 15:58:07 SebastianL2 cardmgr[191]: watching 1 sockets Aug 29 15:58:07 SebastianL2 kernel: cs: IO port probe 0x0c00-0x0cff: clean. Aug 29 15:58:07 SebastianL2 kernel: cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x87f Aug 29 15:58:07 SebastianL2 kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x400-0x40f 0x4d0-0x4d7 Aug 29 15:58:07 SebastianL2 cardmgr[192]: starting, version is 3.2.2 Aug 29 15:58:07 SebastianL2 kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. Aug 29 15:58:07 SebastianL2 cardmgr[192]: socket 0: ZCOMAX AirRunner/XI-300 Aug 29 15:58:08 SebastianL2 kernel: eth1: Station identity 001f:0003:0000:0008 Aug 29 15:58:08 SebastianL2 kernel: eth1: Looks like an Intersil firmware version 0.8.3 Aug 29 15:58:08 SebastianL2 kernel: eth1: Ad-hoc demo mode supported Aug 29 15:58:08 SebastianL2 kernel: eth1: IEEE standard IBSS ad-hoc mode supported Aug 29 15:58:08 SebastianL2 kernel: eth1: WEP supported, 104-bit key Aug 29 15:58:08 SebastianL2 kernel: eth1: MAC address 00:00:CB:06:01:B4 Aug 29 15:58:08 SebastianL2 kernel: eth1: Station name "Prism I" Aug 29 15:58:08 SebastianL2 kernel: eth1: ready Aug 29 15:58:08 SebastianL2 kernel: eth1: index 0x01: Vcc 5.0, irq 5, io 0x0100-0x013f Aug 29 15:58:08 SebastianL2 cardmgr[192]: executing: './network start eth1' Aug 29 15:58:08 SebastianL2 kernel: eth1: Error -110 setting multicast list. Aug 29 15:58:08 SebastianL2 last message repeated 2 times Aug 29 15:58:08 SebastianL2 kernel: eth1: New link status: Connected (0001) [...] Aug 29 16:00:41 SebastianL2 kernel: orinoco_lock() called with hw_unavailable (dev=cf34b800) Aug 29 16:00:41 SebastianL2 cardmgr[192]: executing: './network stop eth1' [...] Aug 29 16:00:44 SebastianL2 cardmgr[192]: socket 0: ZCOMAX AirRunner/XI-300 Aug 29 16:00:44 SebastianL2 kernel: GetNextTuple(). No matching CIS configuration, maybe you need the ignore_cis_vcc=1 parameter. Aug 29 16:00:44 SebastianL2 kernel: orinoco_cs: GetFirstTuple: No more items Aug 29 16:00:45 SebastianL2 cardmgr[192]: get dev info on socket 0 failed: Resource temporarily unavailable
Quoted 31 lines · Sebastian Reichelt
Hello!
After switching from 2.4.20 to 2.4.21 (Debian unstable package kernel-source-2.4.21-5), my wireless LAN PCMCIA card stopped working when I hot-removed and reinserted it. I got these messages in
/var/log/syslog, plus a high beep on removal and a high and then a low beep on reinsertion:Upon removal:
Aug 29 16:00:41 SebastianL2 kernel: orinoco_lock() called with
hw_unavailable(dev=cf34b800)Upon reinsertion:
Aug 29 16:00:44 SebastianL2 cardmgr[192]: socket 0: ZCOMAX AirRunner/XI-300 Aug 29 16:00:44 SebastianL2 kernel: GetNextTuple(). No matching CIS configuration, maybe you need the ignore_cis_vcc=1 parameter. Aug 29 16:00:44 SebastianL2 kernel: orinoco_cs: GetFirstTuple: No more items Aug 29 16:00:45 SebastianL2 cardmgr[192]: get dev info on socket 0failed: Resource temporarily unavailable
I looked at the changes between the two kernels, in
orinoco.c,orinoco_cs.c, andhermes.c, and it seems that quite a bit of code was restructured. So unfortunately, I cannot narrow it down to a single change that caused this. The attached patch fixes the problem for me, but it is NOT a simple copy from the old driver, and it may not be correct at all. However, it might give someone a hint about what went wrong. Anyway, even with this patch, I still get the "orinoco_lock()called withhw_unavailable" message when I remove the card.
Quoted 7 lines
Sorry if I'm posting a patch for a problem that has already been fixed in 2.4.22. The Debian package is still at 2.4.21, and I don't know anything about the Debian patches and why they are needed, etc. If I can just install a kernel from kernel.org, I will do this, and try to see if the problem is still there (I can see an item "orinoco driver update" in the changelog, but it's not specific). Should I also install a 2.6 kernel and check?
Sebastian,
Can you please try 2.4.22? It contains orinoco changes including in the area you changed.
Quoted 2 lines
Can you please try 2.4.22? It contains orinoco changes including in the area you changed.
Sorry, 2.4.22 (from kernel.org) just hangs when I insert the card, after the first of two beeps. Ctrl-Alt-Del doesn't work. No messages are printed except the usual "cs: memory probe 0xa0000000-0xa0ffffff:
clean.", and syslog doesn't seem to have been flushed (it's cut off at a higher position).
One thing I noticed from syslog is that the socket is assigned another
IRQ: 5 instead of 9.
Signature · 1 line
Sebastian Reichelt
Quoted 11 lines · Sebastian Reichelt
Quoted 2 lines
Can you please try 2.4.22? It contains orinoco changes including in the area you changed.
Sorry, 2.4.22 (from kernel.org) just hangs when I insert the card, after the first of two beeps. Ctrl-Alt-Del doesn't work. No messages are printed except the usual "cs: memory probe 0xa0000000-0xa0ffffff:
clean.", and syslog doesn't seem to have been flushed (it's cut off at a higher position).One thing I noticed from syslog is that the socket is assigned another
IRQ: 5 instead of 9.
Hum, are you using ACPI? There have a few IRQ assignment issues reported with the new ACPI in 2.4.22.
Can you please try booting with "pci=noacpi" option ?
Not sure, but can this be related with the stuff commented before in this list with the subjects "Airo Net 340 PCMCIA WiFi Card trouble" ?
Quoted 28 lines · Marcelo Tosatti
Quoted 11 lines · Sebastian Reichelt
Quoted 2 lines
Can you please try 2.4.22? It contains orinoco changes including in the area you changed.
Sorry, 2.4.22 (from kernel.org) just hangs when I insert the card, after the first of two beeps. Ctrl-Alt-Del doesn't work. No messages are printed except the usual "cs: memory probe 0xa0000000-0xa0ffffff:
clean.", and syslog doesn't seem to have been flushed (it's cut off at a higher position).One thing I noticed from syslog is that the socket is assigned another
IRQ: 5 instead of 9.Hum, are you using ACPI? There have a few IRQ assignment issues reported with the new ACPI in 2.4.22.
Can you please try booting with "pci=noacpi" option ?
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 4 lines
Hum, are you using ACPI? There have a few IRQ assignment issues reported with the new ACPI in 2.4.22.
Can you please try booting with "pci=noacpi" option ?
Yes, thanks. That solves both problems (the reinsertion detection and the crash). I still get the message "orinoco_lock() called with hw_unavailable" in syslog, just in case that means something.
Speaking about messages, ever since I've been using PCMCIA (the SourceForge stuff for 2.2 and the kernel support in 2.4), I've been getting the following message three times in a row after insertion:
eth1: Error -110 setting multicast list.
I was told on SourceForge that I should just ignore it. However, it covered by login prompt, so I simply commented out everything about "multicasting" in orinoco.c. Is there a correct way to handle this?
Signature · 1 line
Sebastian Reichelt