Skip to contentSkip to conversation

Linksys connectivity problem using 2.6.0-test4

DISCUSSION Fawad Halim 2 participants 3 messages Sep 10, 2003

lore
Share & tools
lore
#0 lore raw

Hi,
I'm having trouble connecting to the http based admin ports on my
LinkSys VPN router (BEFVP41) using the 2.6.0-test4 kernel on Redhat 9. The connectivity works fine with 2.4.20-19.9 from Redhat as well as other 2.4.x kernels. With the 2.6 kernel, I can ping the machine, but can't connect to the http ports (80, 8080)

# uname -a
Linux chuckie 2.6.0-test4-fh1 #1 Mon Sep 1 05:43:07 CDT 2003 i686 athlon i386 GNU/Linux
# nmap 192.168.3.1

Starting nmap 3.30 ( http://www.insecure.org/nmap/ ) at 2003-09-10 06:42 CDT Interesting ports on 192.168.3.1:
(The 1642 ports scanned but not shown below are in state: closed)

Port       State       Service
80/tcp     open        http
8080/tcp   open        http-proxy

Nmap run completed -- 1 IP address (1 host up) scanned in 2.468 seconds

# ping -c 1 192.168.3.1
PING 192.168.3.1 (192.168.3.1) 56(84) bytes of data.
64 bytes from 192.168.3.1: icmp_seq=1 ttl=149 time=1.44 ms

--- 192.168.3.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.448/1.448/1.448/0.000 ms

# telnet 192.168.3.1 80
Trying 192.168.3.1...
telnet: connect to address 192.168.3.1: Connection refused

The VPN router is doing NAT correctly for both kernels, and connectivity to services other than the router itself is fine.

I am not sure where to even begin debugging this problem.

Regards
-fawad

#1 lore raw
Quoted 7 lines · Fawad Halim

Hi,
I'm having trouble connecting to the http based admin ports on my
LinkSys VPN router (BEFVP41) using the 2.6.0-test4 kernel on Redhat 9. The connectivity works fine with 2.4.20-19.9 from Redhat as well as other 2.4.x kernels. With the 2.6 kernel, I can ping the machine, but can't connect to the http ports (80, 8080)

<skip>

Quoted 7 lines
# telnet 192.168.3.1 80
Trying 192.168.3.1...
telnet: connect to address 192.168.3.1: Connection refused

The VPN router is doing NAT correctly for both kernels, and connectivity to services other than the router itself is fine.

Make sure that you not using ECN - my Linksys refuses incoming connections with ECN. Passes them tohrough just fine, tough.

Dmitry

#2 lore raw

Dmitry, Thanks for the pointer. In 2.6, apparently ECN is enabled by default. Disabling it did the trick.

-fawad

Quoted 22 lines · Fawad Halim
Quoted 7 lines

Hi,
I'm having trouble connecting to the http based admin ports on my
LinkSys VPN router (BEFVP41) using the 2.6.0-test4 kernel on Redhat 9. The connectivity works fine with 2.4.20-19.9 from Redhat as well as other 2.4.x kernels. With the 2.6 kernel, I can ping the machine, but can't connect to the http ports (80, 8080)

<skip>

Quoted 7 lines
# telnet 192.168.3.1 80
Trying 192.168.3.1...
telnet: connect to address 192.168.3.1: Connection refused

The VPN router is doing NAT correctly for both kernels, and connectivity to services other than the router itself is fine.

Make sure that you not using ECN - my Linksys refuses incoming connections with ECN. Passes them tohrough just fine, tough.

Dmitry