Skip to contentSkip to conversation

[[email protected]: visws linux-2.6.0-test5 qla1280 isues]

[email protected]: visws linux-2.6.0-test5 qla1280 isues [email protected] 1 participant 1 message Sep 26, 2003

lore
Share & tools
lore
#0 lore raw

----- Forwarded message from Florian Boor <[email protected]> -----

Subject: visws linux-2.6.0-test5 qla1280 isues
From: Florian Boor <[email protected]>
To: [email protected]
X-Mailer: Ximian Evolution 1.4.4

Hi Andrey!

Greetings from kernel hacker meeting in Oldenburg :-)

My first task for today was war compiling a kernel with qla1280 debug support. It still hangs... here the output:

qla1x160: Supported Device Found VID=1077 DID=1080 SSVID=1077 SSDID=1
qla1280: QLA1080 found on PCI bus 1, dev 0
Configure PCI space for adapter...
scsi(0): Reading NVRAM
qla1280_read_nvram: Completed Reading NVRAM
scsi(0): Determining if RISC is loaded
qla1280: NVRAM configured to load RISC load.
scsi(0): Verifying chip
qla1280_chip_diag: Checking mailboxes of chip
scsi(0): Setup chip
qla1280_setup_chip: DMA RISC code (15675) words
qla1280_setup_chip: Verifying checksum of loaded RISC code.
qla1280_setup_chip: start firmware running.
scsi(0): Configure NVRAM parameters
qla1280 : initiator scsi id bus[0]=7
qla1280 : initiator scsi id bus[1]=0
qla1280 : bus reset delay[0]=5
qla1280 : bus reset delay[1]=0
qla1280 : retry count[0]=0
qla1280 : retry delay[0]=0
qla1280 : retry count[1]=0
qla1280 : retry delay[1]=0
qla1280 : async data setup time[0]=9
qla1280 : async data setup time[1]=0
qla1280 : req/ack active negation[0]=1
qla1280 : req/ack active negation[1]=0
qla1280 : data line active negation[0]=1
qla1280 : data line active negation[1]=0
qla1280 : disable loading risc code=0
qla1280 : enable 64bit addressing=0
qla1280 : selection timeout limit[0]=250
qla1280 : selection timeout limit[1]=0
qla1280 : max queue depth[0]=256
qla1280 : max queue depth[1]=0
scsi(0:0): Resetting SCSI BUS
scsi0 : QLogic QLA1080 PCI to SCSI Host Adapter: bus 1 device 0 irq 16

       Firmware version:  8.15.00, Driver version 3.23.35

Any
idea?
I'll be here working on SGI320 and iPaq for the next two days, maybe i'm able to port the monitor detection code from 2.2.x. :-)

Greetings

Florian

Signature · 13 lines
The dream of yesterday                     Florian Boor
is the hope of today                       Tel: 0271-7411487 
and the reality of tomorrow.               [email protected]
[Robert Hutchings Goddard, 1904]           [email protected]

6C 44 30 4C 43 20 6B 61 16 07 0F AA E6 97 70 A8


----- End forwarded message -----

-- 
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net