2.6.x net driver updates

This should fix the build. Only thing left not building is g_ncr5380...

Linus, please do a

bk pull bk://kernel.bkbits.net/jgarzik/net-drivers-2.5

This will update the following files:

 drivers/usb/net/Makefile.mii      |    6 
 drivers/net/Kconfig               |   11 
 drivers/net/Makefile              |   28 --
 drivers/net/e100/e100.h           |    1 
 drivers/net/e100/e100_config.c    |    2 
 drivers/net/e100/e100_config.h    |    1 
 drivers/net/e100/e100_main.c      |   49 +---
 drivers/net/e1000/e1000.h         |    8 
 drivers/net/e1000/e1000_ethtool.c |   14 -
 drivers/net/e1000/e1000_hw.c      |   39 +--
 drivers/net/e1000/e1000_hw.h      |    2 
 drivers/net/e1000/e1000_main.c    |   90 ++++---
 drivers/net/e1000/e1000_osdep.h   |    2 
 drivers/net/hamradio/baycom_epp.c |    4 
 drivers/net/pcmcia/Kconfig        |    1 
 drivers/net/pcmcia/smc91c92_cs.c  |    8 
 drivers/net/sk98lin/skdim.c       |    5 
 drivers/net/sk98lin/skge.c        |  103 +++-----
 drivers/net/sk98lin/skproc.c      |  463 ++++++++++++++++----------------------
 drivers/net/tulip/Kconfig         |    1 
 drivers/net/wan/sealevel.c        |   36 +-
 drivers/net/wan/z85230.c          |   58 ++--
 drivers/net/wireless/orinoco.c    |    4 
 drivers/usb/net/Kconfig           |    2 
 24 files changed, 447 insertions(+), 491 deletions(-)

through these ChangeSets:

<[email protected]> (03/09/27 1.1371)
[PATCH] select MII

The patch below switches MII to be select'ed instead of including it in the Makefile.

Note that this patch requires a recent Linus' tree with the select CRC32 patch included.

diffstat output:

    drivers/net/Kconfig          |   11 +++++++++++
    drivers/net/Makefile         |   28 +++++++++++-----------------
    drivers/net/pcmcia/Kconfig   |    1 +
    drivers/net/tulip/Kconfig    |    1 +
    drivers/usb/net/Kconfig      |    2 ++
    drivers/usb/net/Makefile.mii |    6 ------
    6 files changed, 26 insertions(+), 23 deletions(-)

Tangential to the patch I observed a small problem (not fixed in the patch):
MII depends on NET_ETHERNET, but USB_PEGASUS and USB_USBNET depend only on NET.

cu
Adrian

<[email protected]> (03/09/27 1.1370)
[PATCH] wan/z8530 deadlocks

Existing code for drivers/net/wan/z8530 is riddled with self-deadlocks and irq flag confusion. For example:
z8530_init -> do_z8530_init -> write_zsreg
self deadlocks on the channel lock.

Several places acquire both the channel and dma lock and then reuse the same irq flags variable - ouch.

This code at least, correctly probes (for no device case) on SMP. Other paths verified by inspection.

<[email protected]> (03/09/27 1.1369)
[PATCH] sealevel -- syncppp startup fix

The sealevel driver called sppp_attach before checking that board existed and never called detach in the error path.

My change is to call sppp_attach from the netdev->init hook which happens later in the process, and call detach from the uninit hook.

Also, changed the structure element 'netdev' to 'pppdev' to avoid confusion.

Here is the fix against 2.6.0-test5 latest

<[email protected]> (03/09/27 1.1368)
[netdrvr smc91c92_cs] select proper bank for MII registers

<[email protected]> (03/09/27 1.1367)
[netdrvr] build fixes

For e1000 and baycom_epp.

Contributed by Jeff Garzik.

<[email protected]> (03/09/27 1.1366)
[PATCH] janitor: e100: cleanup #includes

Hi,
Please apply to 2.6.0-test5-current.

Thanks,
--
~Randy

From: Randy Hron <[email protected]>

Remove unneeded include of version.h.
Test compiled against 2.6.0-test5-bk9.

    linux-260-t5bk12-kj-rddunlap/drivers/net/e100/e100.h |    1 -
    1 files changed, 1 deletion(-)

<[email protected]> (03/09/27 1.1365)
[PATCH] janitor: hermes: delete verify_area call

Hi,
Please apply to 2.6.0-test5-current.

Thanks,
--
~Randy

From: Domen Puncer <[email protected]>

IMO, that verify_area wasn't needed.

    linux-260-t5bk12-kj-rddunlap/drivers/net/wireless/orinoco.c |    4 ----
    1 files changed, 4 deletions(-)

<[email protected]> (03/09/27 1.1364)
[e100] trying to pci_alloc before pci_enable

* Some archs don't like calling pci_alloc_consistent before calling pci_enable_device. (Imagine that). This corrects that.

<[email protected]> (03/09/27 1.1363)
[e100] h/w can't do IPv6 checksum offloading

* Driver was advertising HW_CSUM, but hardware is only capable of IP_CSUM.

<[email protected]> (03/09/27 1.1362)
[e100] PRO/10+ not configured properly

* PRO/10+ (10 Mbps-only card) was not configured properly so it didn't pass traffic.

<[email protected]> (03/09/27 1.1361)
[e1000] misc

* removed unused var, ASSERT macro
* missed a free_netdev() in probe cleanup undo.

<[email protected]> (03/09/27 1.1360)
[e1000] better propagation of error codes

* Better propagation of error codes during probe/open paths. {Janice Girouard ([email protected])]

<[email protected]> (03/09/27 1.1359)
[e1000] force 1000/full on SERDES connected to back-plane

* Bug fix: SERDES devices might be connected to back-plan switch that doesn't support auto-neg, so add the capability to force 1000/full.

<[email protected]> (03/09/27 1.1358)
[e1000] flow control updates

* handle ethtool force flow control
* correctly set flow control hi/low watermarks based on size of Rx FIFO area. The size can change if doing Jumbo Frames or, in the case of 82547, is smaller to start with.
* was not properly forcing flow control settings to fc_none if using strict IEEE flow control override.

<[email protected]> (03/09/27 1.1357)
[netdrvr sk98lin] use seq_file for /proc

Replace proc_read with seq_file interface which is much cleaner.

Also, instead of searching the list of devices looking for the name which is slow and would break if interface name changes; store a pointer to device in the proc entry, and retrieve it from the information saved by single_open.

Formatting and other behaviours are retained.

<[email protected]> (03/09/27 1.1356)
[netdrvr skge] handle proc_fs errors.

Existing code does not
- check if proc_fs functions return error.
- use proc_mkdir to make the directory.

Note pSkRootDir defined twice.

<[email protected]> (03/09/27 1.1355)
[netdrvr sk98lin] build on smp fix

There is no exported variable called smp_num_cpus! so this driver won't build on SMP. Since the local variable is never used anyway just get rid of it.

This applies against 2.6.0-test5-bk13 which has the last vendor driver update.