2.4.22 hangs upon echo > /proc/acpi/alarm
ACPI version is 20031002
Initial backtrace obtained with kdb:
acpi_os_read_port+36
acpi_hw_lowlevel_read+7b
acpi_ev_gpe_detect+94
acpi_ev_sci_xrupt_handler+3c
acpi_irq+d
handle_IRQ_event+31
do_IRQ+72
call_do_IRQ+5
do_softirq+5a
do_IRQ+a1
proc_file_write+9b
sys_write+be
system_call+33
Further stepping shows endless loop around:
acpi_ev_gpe_detect+80
acpi_hw_lowlevel_read
acpi_os_read_port
acpi_ut_get_region_name
acpi_ut_debug_print
acpi_ut_debug_print
jmp acpi_ev_gpe_detect+80
Debugging is compiled in, but no meesages go to dmesg
How to enable acpi_ut_debug_print output?
Regards
Michael
Quoted 28 lines · Michael Frank
ACPI version is 20031002
Initial backtrace obtained with kdb:
acpi_os_read_port+36
acpi_hw_lowlevel_read+7b
acpi_ev_gpe_detect+94
acpi_ev_sci_xrupt_handler+3c
acpi_irq+d
handle_IRQ_event+31
do_IRQ+72
call_do_IRQ+5
do_softirq+5a
do_IRQ+a1
proc_file_write+9b
sys_write+be
system_call+33Further stepping shows endless loop around:
acpi_ev_gpe_detect+80
acpi_hw_lowlevel_read
acpi_os_read_port
acpi_ut_get_region_name
acpi_ut_debug_print
acpi_ut_debug_print
jmp acpi_ev_gpe_detect+80
Quoted 3 lines
Debugging is compiled in, but no meesages go to dmesg
How to enable
acpi_ut_debug_printoutput?
printk() can be called from anywhere but the text is only stored in the log buffer. The text is written from the log buffer to the console or syslog when the kernel is not running in interrupt context. This is a common problem with printk, you get no output when debugging interrupt problems.
Since you have already applied the kdb patch, change acpi to add #include <linux/kdb.h> and call kdb_printf() instead of printk for debugging messages. kdb_printf uses polling mode I/O so you get the output immediately.
Quoted 40 lines · Keith Owens
Quoted 28 lines · Michael Frank
ACPI version is 20031002
Initial backtrace obtained with kdb:
acpi_os_read_port+36
acpi_hw_lowlevel_read+7b
acpi_ev_gpe_detect+94
acpi_ev_sci_xrupt_handler+3c
acpi_irq+d
handle_IRQ_event+31
do_IRQ+72
call_do_IRQ+5
do_softirq+5a
do_IRQ+a1
proc_file_write+9b
sys_write+be
system_call+33Further stepping shows endless loop around:
acpi_ev_gpe_detect+80
acpi_hw_lowlevel_read
acpi_os_read_port
acpi_ut_get_region_name
acpi_ut_debug_print
acpi_ut_debug_print
jmp acpi_ev_gpe_detect+80Quoted 3 lines
Debugging is compiled in, but no meesages go to dmesg
How to enable
acpi_ut_debug_printoutput?
printk()can be called from anywhere but the text is only stored in the log buffer. The text is written from the log buffer to the console or syslog when the kernel is not running in interrupt context. This is a common problem with printk, you get no output when debugging interrupt problems.
Quoted 5 lines
Since you have already applied the kdb patch, change acpi to add #include <
linux/kdb.h> and callkdb_printf()instead of printk for debugging messages.kdb_printfuses polling mode I/O so you get the output immediately.
Thank you for your reply. I'll make good use of kdb_printf in future.
In this case however the messages did not even go into the dmesg buffer as the acpi debug output (via its own printf) must be enabled by debug section flags which were disabled. I'll file a bug report against acpi asap.
I have two questions about kdb 3.0, x86 hw on 2.4.22 kernel
- is there any netpoll interface for kdb for legacy free hw wo serial port.
- on another non-acpi machine kdb hangs permanently and blinking kbleds stop once
- any key is pressed on the at keyboard
- after about a minute inside kdb (operating via serial port)
Regards
Michael
Quoted 1 line · Michael Frank
I have two questions about kdb 3.0, x86 hw on 2.4.22 kernel
kdb 3.0 is ancient, current is kdb v4.3.
Quoted 1 line
- is there any netpoll interface for kdb for legacy free hw wo serial port.
No netpoll interface. netpoll is not in the standard kernel, kdb patches are only against the standard kernels.
For legacy free hardware, kdb v4.3 has a working USB keyboard polled mode. Build with
CONFIG_USB=yCONFIG_USB_UHCI=y (or OHCI)CONFIG_USB_HID=mCONFIG_USB_HIDINPUT=yCONFIG_USB_KBD=yCONFIG_KDB_USB=y
Quoted 3 lines
- on another non-acpi machine kdb hangs permanently and blinking kbleds stop once
- any key is pressed on the at keyboard
- after about a minute inside kdb (operating via serial port)
Sounds like kdb is itself dying. Insufficient data to diagnose, in any case there have been a lot of bug fixes and enhancements to kdb since v3.0.