Printing Garbage
Hi,
suddenly my printer Epson LQ 300 is only printing garbage characters. What could be the reason.
I am in RH 7.3. I went to DOS the same, only garbage printing.
There are no error messages. Starting LPD says OK. Lprm, lpq etc function normally.
Running the printer self test performs flawlessly, meaning the printer does work. I checked all the cables, can't find anything wrong.
Any ideas, help?
Regards
Signature · 7 lines
Peter - To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.linux-learn.org/faqs
Try a different printer if it works correctly then buy a new printer.
Frank
Quoted 10 lines · Peter
Hi,
suddenly my printer Epson LQ 300 is only printing garbage characters. What could be the reason.
I am in RH 7.3. I went to DOS the same, only garbage printing.
There are no error messages. Starting LPD says OK. Lprm, lpq etc function normally.
Quoted 6 lines
Running the printer self test performs flawlessly, meaning the printer does work. I checked all the cables, can't find anything wrong.
Any ideas, help?
Regards
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
Quoted 7 lines · Peter
Hi,
suddenly my printer Epson LQ 300 is only printing garbage characters. What could be the reason.
I am in RH 7.3. I went to DOS the same, only garbage printing.
Quoted 7 lines
There are no error messages. Starting LPD says OK. Lprm, lpq etc function normally.
Running the printer self test performs flawlessly, meaning the printer does work. I checked all the cables, can't find anything wrong.
Any ideas, help?
Well, if the problem occurs with DOS as well as Linux, that certainly suggests it is not a Linux problem. There are a couple of things to do before you buy a new printer, though.
1. Have you power-cycled the printer? If not, do so, just in case something caused a transient change in the settings. Leave it off for a minute or so.
2. You say "I checked all the cables, can't find anything wrong". Checked *how*? Visually? That wouldn't catch a single broken wire, which would be enough to turn good signals into jabberwocky ... and could easily happen if the cable is bent sharply at either end (I've never actually seen this with a parallel or serial cable, but I have seen it happen to VGA cables). The only real way to test for a cable problem, unless you are better with a VOM than I am, is to substitute another cable and still see the problem (or to use the cable in a different setup and see no problem there ... even that is not a *completely* certain test, though).
3. You probably want to ask for help on a support list for the printer, not a Linux list. There, the question to ask is if there is some persistent change to the configuration that can occur accidentally ... stay in NV RAM or whatever.
4. Any chance that you made a BIOS change to the port (you don't way if this is a parallel, serial, USB, or LAN/Ethernet setup, so I can't be more specific than that ... though I suppose you use of DOS implies either parallel or serial)?
Were I to **guess**, it would be that you missed a bad cable. Only a guess, though.
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
Quoted 38 lines · Ray Olszewski
Quoted 7 lines · Peter
Hi,
suddenly my printer Epson LQ 300 is only printing garbage characters. What could be the reason.
I am in RH 7.3. I went to DOS the same, only garbage printing.
Quoted 7 lines
There are no error messages. Starting LPD says OK. Lprm, lpq etc function normally.
Running the printer self test performs flawlessly, meaning the printer does work. I checked all the cables, can't find anything wrong.
Any ideas, help?
Well, if the problem occurs with DOS as well as Linux, that certainly suggests it is not a Linux problem. There are a couple of things to do before you buy a new printer, though.
1. Have you power-cycled the printer? If not, do so, just in case something caused a transient change in the settings. Leave it off for a minute or so.
2. You say "I checked all the cables, can't find anything wrong". Checked *how*? Visually? That wouldn't catch a single broken wire, which would be enough to turn good signals into jabberwocky ... and could easily happen if the cable is bent sharply at either end (I've never actually seen this with a parallel or serial cable, but I have seen it happen to VGA cables). The only real way to test for a cable problem, unless you are better with a VOM than I am, is to substitute another cable and still see the problem (or to use the cable in a different setup and see no problem there ... even that is not a *completely* certain test, though).
3. You probably want to ask for help on a support list for the printer, not a Linux list. There, the question to ask is if there is some persistent change to the configuration that can occur accidentally ... stay in NV RAM or whatever.
Quoted 8 lines
4. Any chance that you made a BIOS change to the port (you don't way if this is a parallel, serial, USB, or LAN/Ethernet setup, so I can't be more specific than that ... though I suppose you use of DOS implies either parallel or serial)?
Were I to **guess**, it would be that you missed a bad cable. Only a guess, though.
Hi All
First I assume competence with my response.
By that I mean that the person knows to do all the normal clean up things like check printer cable, check plugged in, turn off printer to clear buffer, clear files from cash et before a question like that is ask.
For mysself I have a printer HO 890 C connected to a dual boot Win XP / Md 9.1 box that at times refuses to print correct.
I have seen the same file printed under the same program in the same operating system print and not print.
This printer may and often is connected to another dual boot Win 98 / RH 6.3 box where it always works.
There is a third box RH 7.3 form which it also always works.
At the last SLUG meeting here in Tampa I mentioned the problem because I thought it has something to do with the fact that I had split the HD of the offending computer into 3 sectors. The Win XP can see two: WIN XP and Common; the Md 9.1 can see two: Common and Md 9.1. I was concerned with the partition format being used for Common.
Oh I for got to mention the problem is independent of file format except for plain text which always works. All other formats work and/or fail seeming at random.
Turns out that regardless of the file format used any files brought up in Win XP Office become corrupt. If Win XP Office is not used then there is no problem.
I found the problem by the simple means of using a second Canon portable printer I have.
Regards
Frank
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
Hi, my own worst suspicion turned out to be true. The motherboard had failed which
was a little less then 2 years old, yet old enough that this type can not be found any longer and therefore all the sockets of the new boards are different forcing me to buy as well a new processor and memories. Guess that keeps the industry running.
The new board is P4VMM2 by ECS Elitegroup and I was unable to configure X in RH7.3. The first time this happened since RH5.2. I then went over to Slackware 9.1, got X surprisingly working there, copied XF86config over to RH and all is fine
except I am $200 poorer.
Thanks and regards
Peter
Quoted 14 lines · Peter
Hi,
suddenly my printer Epson LQ 300 is only printing garbage characters. What could be the reason.
I am in RH 7.3. I went to DOS the same, only garbage printing.
There are no error messages. Starting LPD says OK. Lprm, lpq etc function normally.
Running the printer self test performs flawlessly, meaning the printer does work. I checked all the cables, can't find anything wrong.
Any ideas, help?
Quoted 2 lines · [email protected] said:
Were I to **guess**, it would be that you missed a bad cable. Only a guess, though.
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
Greetings: Not following the thread; if the parallel port was on the MB there could have been a simple work around. (Too late now though, eh?)
Parallel port expansion cards are available for $10upUS.. I've had to do that several times to "rescue" a MB.. Of course, some times it didn't work. <grin>
Glad to see you've rediscovered the very fine Slackware 9X, IMHO.
Hal - in Terra Alta, WV - Slackware GNU/Linux 9.0 (2.4.20)
Proprietary Formats Unacceptable
Quoted 13 lines · Peter
Hi, my own worst suspicion turned out to be true. The motherboard had failed which
was a little less then 2 years old, yet old enough that this type can not be found any longer and therefore all the sockets of the new boards are different forcing me to buy as well a new processor and memories. Guess that keeps the industry running.The new board is P4VMM2 by ECS Elitegroup and I was unable to configure X in RH7.3. The first time this happened since RH5.2. I then went over to Slackware 9.1, got X surprisingly working there, copied XF86config over to RH and all is fine
except I am $200 poorer.
Quoted 20 lines
Thanks and regards
Peter
Quoted 14 lines · Peter
Hi,
suddenly my printer Epson LQ 300 is only printing garbage characters. What could be the reason.
I am in RH 7.3. I went to DOS the same, only garbage printing.
There are no error messages. Starting LPD says OK. Lprm, lpq etc function normally.
Running the printer self test performs flawlessly, meaning the printer does work. I checked all the cables, can't find anything wrong.
Any ideas, help?
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs