USB timeout with printer
I have a HP LaserJet 1300 that I'm using over USB.
(drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 8 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1017)
What's getting to be very annoying is that usually within a day after printing something, I get the message usb 1-2: control timeout on ep0in, and the printer needs to be power cycled. I get other weird errors sometimes, like "drivers/usb/class/usblp.c: usblp0: error -110 reading printer status". I don't have any evidence that this is Linux's fault, but it seems like a fairly likely possibility, at least if you consider it an incompatibility with the printer rather than a bug. My mouse uses USB and it works fine. I'm using an expensive Belkin USB cable. The kernel version is 2.6.0-test9-bk17. Here is some information on my USB controller:
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c800 [size=32]
Capabilities: <available only to root>
I think this may have started a few -test revisions ago, but I'm not sure. I only purchased the printer fairly recently so it's not like I can say that it's worked for years.
Hi Aaron :)
* Aaron Lehmann <[email protected]> dixit:
Quoted 5 lines
What's getting to be very annoying is that usually within a day after printing something, I get the message usb 1-2: control timeout on ep0in, and the printer needs to be power cycled. I get other weird errors sometimes, like "
drivers/usb/class/usblp.c: usblp0: error -110 reading printer status".
I have exactly the same problem, quite frequently lately (I use
2.4.21), with a PostScript capable laser printer, namely Lexmark Optra E312.
I have a VIA chipset, too.
Raúl Núñez de Arenas Coronado
Signature · 2 lines
Linux Registered User 88736 http://www.pleyades.net & http://raul.pleyades.net/
Quoted 21 lines · On Mon, 1 Dec 2003 11:50:32 -0800 Aaron Lehmann wrote:
I have a HP LaserJet 1300 that I'm using over USB.
(
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 8 if 0 alt 1 proto 2 vid0x03F0pid0x1017)What's getting to be very annoying is that usually within a day after printing something, I get the message usb 1-2: control timeout on ep0in, and the printer needs to be power cycled. I get other weird errors sometimes, like "
drivers/usb/class/usblp.c: usblp0: error -110 reading printer status". I don't have any evidence that this is Linux's fault, but it seems like a fairly likely possibility, at least if you consider it an incompatibility with the printer rather than a bug. My mouse uses USB and it works fine. I'm using an expensive Belkin USB cable. The kernel version is 2.6.0-test9-bk17. Here is some information on my USB controller:00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c800 [size=32]
Capabilities: <available only to root>
Quoted 3 lines
I think this may have started a few -test revisions ago, but I'm not sure. I only purchased the printer fairly recently so it's not like I can say that it's worked for years.
I have experienced similar issues with LaserJet 1300:
http://marc.theaimsgroup.com/?l=linux-usb-devel&m=106208938406301&w=2
http://marc.theaimsgroup.com/?w=2&r=1&s=laserjet+1300+lockup&q=t