Skip to contentSkip to conversation

VIA IDE DMA problems with sleeping harddisk

2.6.0-test11 Claas Langbehn 2 participants 2 messages Dec 16, 2003 – Dec 17, 2003

lore
Share & tools
lore
#0 lore raw

Hello,

I have got two harddiscs in my system (hda, hdb) and an CD-R/W writer as hdc. Both harddiscs are UDMA-100 drives. First of all, it is strange that the drives are only set to a transfer rate of 88.8 MB/s and not to 100MB/s (see below).

hdb is sleeping most of the time (hdparm -S), but when I need the drive, it does not spin up fast enough, so that the kernel messages say:

    Dec 16 15:13:14 kernel: hdb: dma_timer_expiry: dma status == 0x61
    Dec 16 15:13:24 kernel: hdb: DMA timeout error
    Dec 16 15:13:24 kernel: hdb: dma timeout error: status=0xd0 { Busy }
    Dec 16 15:13:24 kernel: 
    Dec 16 15:13:24 kernel: hda: DMA disabled
    Dec 16 15:13:24 kernel: hdb: DMA disabled
    Dec 16 15:13:25 kernel: ide0: reset: success

In /proc/ide/via i see, that hda is using PIO now:

-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: PIO UDMA UDMA PIO
Address Setup: 120ns 120ns 120ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 90ns 90ns 330ns
Data Recovery: 30ns 30ns 30ns 270ns
Cycle Time: 120ns 22ns 60ns 600ns
Transfer Rate: 16.6MB/s 88.8MB/s 33.3MB/s 3.3MB/s

When I re-enable DMA afterwards the messages say:

Dec 16 15:13:49 zoo kernel: blk: queue dfde1200, I/O limit 4095Mb (mask

0xffffffff)

- How do I increase the dma_timer_expiry so that DMA will not be disabled so fast?

- Why does the kernel say "hdb: DMA disabled" but /proc/ide/via says that DMA was only disabled on hda?
Is it a bug or is it enabled again without telling me?

- Which workaround should be considered?

Regards, Claas

# cat /proc/ide/via   (with DMA enabled)

----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.38
South Bridge: VIA vt8235
Revision: ISA 0x0 IDE 0x6
Highest DMA rate: UDMA133
BM-DMA base: 0xdc00
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: yes yes
Simplex only: no no
Cable Type: 80w 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA UDMA UDMA PIO
Address Setup: 120ns 120ns 120ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 90ns 90ns 330ns
Data Recovery: 30ns 30ns 30ns 270ns
Cycle Time: 22ns 22ns 60ns 600ns
Transfer Rate: 88.8MB/s 88.8MB/s 33.3MB/s 3.3MB/s

# uname -a
    Linux zoo 2.6.0-test11 #3 Mon Dec 1 19:57:51 CET 2003 i686 GNU/Linux
#1 lore raw
Quoted 7 lines · Claas Langbehn

Hello,

I have got two harddiscs in my system (hda, hdb) and an CD-R/W writer as hdc. Both harddiscs are UDMA-100 drives. First of all, it is strange that the drives are only set to a transfer rate of 88.8 MB/s and not to 100MB/s (see below).

This is normal. UDMA/133 chipsets often don't support 100MB/sec, because it's not possible with a 266 MHz clock, so instead you get 88.8MB/sec, which is the closest lower value achievable.

Quoted 30 lines

hdb is sleeping most of the time (hdparm -S), but when I need the drive, it does not spin up fast enough, so that the kernel messages say:

    Dec 16 15:13:14 kernel: hdb: dma_timer_expiry: dma status == 0x61
    Dec 16 15:13:24 kernel: hdb: DMA timeout error
    Dec 16 15:13:24 kernel: hdb: dma timeout error: status=0xd0 { Busy }
    Dec 16 15:13:24 kernel: 
    Dec 16 15:13:24 kernel: hda: DMA disabled
    Dec 16 15:13:24 kernel: hdb: DMA disabled
    Dec 16 15:13:25 kernel: ide0: reset: success

In /proc/ide/via i see, that hda is using PIO now:

-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: PIO UDMA UDMA PIO
Address Setup: 120ns 120ns 120ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 90ns 90ns 330ns
Data Recovery: 30ns 30ns 30ns 270ns
Cycle Time: 120ns 22ns 60ns 600ns
Transfer Rate: 16.6MB/s 88.8MB/s 33.3MB/s 3.3MB/s

When I re-enable DMA afterwards the messages say:

Dec 16 15:13:49 zoo kernel: blk: queue dfde1200, I/O limit 4095Mb (mask

0xffffffff)

Quoted 6 lines

- How do I increase the dma_timer_expiry so that DMA will not be disabled so fast?

- Why does the kernel say "hdb: DMA disabled" but /proc/ide/via says that DMA was only disabled on hda?
Is it a bug or is it enabled again without telling me?

DMA is enabled in the chipset but not used by the driver.

Quoted 48 lines

- Which workaround should be considered?

Regards, Claas

# cat /proc/ide/via   (with DMA enabled)

----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.38
South Bridge: VIA vt8235
Revision: ISA 0x0 IDE 0x6
Highest DMA rate: UDMA133
BM-DMA base: 0xdc00
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: yes yes
Simplex only: no no
Cable Type: 80w 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA UDMA UDMA PIO
Address Setup: 120ns 120ns 120ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 90ns 90ns 330ns
Data Recovery: 30ns 30ns 30ns 270ns
Cycle Time: 22ns 22ns 60ns 600ns
Transfer Rate: 88.8MB/s 88.8MB/s 33.3MB/s 3.3MB/s

# uname -a
    Linux zoo 2.6.0-test11 #3 Mon Dec 1 19:57:51 CET 2003 i686 GNU/Linux

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 2 lines
Vojtech Pavlik
SuSE Labs, SuSE CR