atapi cd reported twice in dmesg??
Hello,
I'm migrating to 2.6 after having used 2.0,2.2,2.4 for quite
some years now.
At a first glance, I read ide-scsi is dropped. Okay, no SCSI
support at all for me then. I have one CD writer, and now it
gets reported twice, which I don't understand. I have CONFIG_IDE,CONFIG_BLK_DEV_IDE,CONFIG_BLK_DEV_IDEDSK,CONFIG_IDEDISK_MULTIMODE,CONFIG_BLK_DEV_IDECD set. dmesg reports: "hdc: PCRW804, ATAPI CD/DVD-ROM drive" first
(ok), then "hdc: ATAPI 32X CDROM CD-R/RW drive, 2048kB Cache,
DMA". Prior to the second report, an error is generated:
"end_request: I/O error, dev hdc, sector 0". Reading works fine,
haven't tested writing yet (nor installed X, hence the omission
of blank lines in this mail). Is this a RTFM problem...? Kindest
regards, Xander.
--------------------------------------------------------------------------------
Get your free 15 Mb POP3 email @alexandria.cc
Click here -> http://www.alexandria.cc/
Quoted 16 lines · xander vanwiggen
Hello,
I'm migrating to 2.6 after having used 2.0,2.2,2.4 for quite
some years now.
At a first glance, I read ide-scsi is dropped. Okay, no SCSI
support at all for me then. I have one CD writer, and now it
gets reported twice, which I don't understand. I have CONFIG_IDE,CONFIG_BLK_DEV_IDE,CONFIG_BLK_DEV_IDEDSK,CONFIG_IDEDISK_MULTIMODE,CONFIG_BLK_DEV_IDECD set. dmesg reports: "hdc: PCRW804, ATAPI CD/DVD-ROM drive" first
(ok), then "hdc: ATAPI 32X CDROM CD-R/RW drive, 2048kB Cache,
DMA". Prior to the second report, an error is generated:
"end_request: I/O error, dev hdc, sector 0". Reading works fine,
haven't tested writing yet (nor installed X, hence the omission
of blank lines in this mail). Is this a RTFM problem...? Kindest
regards, Xander.
I'm still running 2.4 on this box, with a combi drive as the primary
slave. That shows twice too, as
hdb: HL-DT-ST RW/DVD GCC-4320B, ATAPI CD/DVD-ROM drive
and then _many_ lines later is the second part
hdb: attached ide-scsi driver.
scsi1: SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: RW/DVD GCC-4320B Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
So I guess all that's happening is that the two parts come together
when we give up ide-scsi. The error messages look as if the kernel is trying to find any partitions, which isn't going to happen without media
- you should see how many error messages I get from an ATPAI ZIP drive in 2.4 when I boot without media, but they're nothing to worry about.
HTH
Ken
Signature · 1 line
I'm as free as a bird now, and this bird you cannot chain.
Quoted 11 lines · xander vanwiggen
Hello,
I'm migrating to 2.6 after having used 2.0,2.2,2.4 for quite
some years now.
At a first glance, I read ide-scsi is dropped. Okay, no SCSI
support at all for me then. I have one CD writer, and now it
gets reported twice, which I don't understand. I have CONFIG_IDE,CONFIG_BLK_DEV_IDE,CONFIG_BLK_DEV_IDEDSK,CONFIG_IDEDISK_MULTIMODE,CONFIG_BLK_DEV_IDECD set. dmesg reports: "hdc: PCRW804, ATAPI CD/DVD-ROM drive" first
(ok), then "hdc: ATAPI 32X CDROM CD-R/RW drive, 2048kB Cache,
DMA". Prior to the second report, an error is generated:
The first is the generic ide probe, the second is ide-cd registering the device. There is nothing wrong, that is how it's supposed to look.
Signature · 1 line
Jens Axboe