Skip to contentSkip to conversation

PROBLEM: nForce2 keeps crashing during network activity

DISCUSSION Ross Dickson 3 participants 5 messages Dec 22, 2003 – Dec 31, 2003

lore
Share & tools
lore
#0 lore raw
Quoted 15 lines
Quoted 15 lines

Jens Kübler wrote:

Hi

My computer will freeze if I produce heavy network traffic. The crashes happen after an arbitrary time and seem not to be related to hardware defects. I tried the onboard nic and the rtl8139 which worked fine for me with my old mainboard. I've copied the same file with windowsXP and tried some other heavy network traffic just to see wheater it might be an hardware error but the system was stable. After I have started to import my home directory via NFS the crashes became more often. I will crash my system if I copy a big file via SMB.
I had the problem with Mandrake 9.1 and now with 9.2 and even compiled my own kernel (mandrake source) with no effect.

Quoted 7 lines
Quoted 2 lines

Any suggestions?

Boot with noapic or acpi=off
--
Regards
Thomas

If the noapic or acpi=off stabilizes it for you and you want to run with apic and io-apic then my patches may help.

You can find them in this thread

Updated Lockup Patches, 2.4.22 - 23 Nforce2, apic timer ack delay, ioapic edge
for NMI debug

If unsubscribed you can find it here
http://linux.derkeiler.com/Mailing-Lists/Kernel/2003-12/4673.html
or here
http://lkml.org/lkml/2003/12/21/156

Regards
Ross Dickson

#1 lore raw
Quoted 5 lines

If the noapic or acpi=off stabilizes it for you and you want to run with apic and io-apic then my patches may help.

You can find them in this thread

Quoted 7 lines

Updated Lockup Patches, 2.4.22 - 23 Nforce2, apic timer ack delay, ioapic edge for NMI debug

If unsubscribed you can find it here
http://linux.derkeiler.com/Mailing-Lists/Kernel/2003-12/4673.html
or here
http://lkml.org/lkml/2003/12/21/156

I played a bit around with apic off and on and still it had no effect. My board keeps crashing. Seems not to be related to apic.

Jens

#2 lore raw
Quoted 15 lines · Jens Kübler
Quoted 5 lines

If the noapic or acpi=off stabilizes it for you and you want to run with apic and io-apic then my patches may help.

You can find them in this thread

Quoted 9 lines

Updated Lockup Patches, 2.4.22 - 23 Nforce2, apic timer ack delay, ioapic edge for NMI debug

If unsubscribed you can find it here
http://linux.derkeiler.com/Mailing-Lists/Kernel/2003-12/4673.html
or here
http://lkml.org/lkml/2003/12/21/156

Quoted 4 lines

I played a bit around with apic off and on and still it had no effect. My board keeps crashing. Seems not to be related to apic.

Jens

I would not count on that if it's an nforce2 board. It's virtually an faq that if nforce2 is unstable then you may actually need apic, local apic, ioapic, a bios update, these patches, maybe athcool utility.

My nforce2 motherboard had ERR count and excessive MIS count in /proc/interrupts due to sharing interrupts between two pci cards. I removed the ethernet card, used the motherboard ethernet and forcedeth driver, so I was not sharing interrupts between pci cards, and that gave me ERR 0 and minimal MIS. Shared interrupts might be your problem.

Personally I found that noapic or acpi=off could not do anything for me either. Currently I have pre-emptive kernel, apic, acpi, local apic.

You can try a bios flash update. This is most hopeful for Award bios. Save your old bios just in case when the flash software asks if you want to save your old bios. We heard from one person who needed to go back to his old bios, but several got rid of their nforce2 crashes by a bios update.

You can try athcool utility turning cpu disconnect off--"athcool off". This stopped crashing for a few. I don't need that.

You can try the patches; they can't hurt and would be easy to remove. To make them work you need apic on in bios, apic and local apic on in kernel config.

-Bob

#3 lore raw
In reply to Ross Dickson
Quoted 14 lines
Quoted 5 lines

If the noapic or acpi=off stabilizes it for you and you want to run with apic and io-apic then my patches may help.

You can find them in this thread

Quoted 7 lines

Updated Lockup Patches, 2.4.22 - 23 Nforce2, apic timer ack delay, ioapic edge
for NMI debug

If unsubscribed you can find it here
http://linux.derkeiler.com/Mailing-Lists/Kernel/2003-12/4673.html
or here
http://lkml.org/lkml/2003/12/21/156

Quoted 4 lines

I played a bit around with apic off and on and still it had no effect. My board keeps crashing. Seems not to be related to apic.

Jens

Might be a mandrake source thing, not liking nforce2 perhaps?

If you don't mind a bit of work, you could download current standard 2.4.23 kern source, add my patches, compile with acpi and uniprocessor ioapic, Athlon etc. use the onboard nic, and try it with apic_tack=1 kernel arg.

Regards
Ross.

#4 lore raw
Quoted 8 lines

Might be a mandrake source thing, not liking nforce2 perhaps?

If you don't mind a bit of work, you could download current standard 2.4.23 kern source, add my patches, compile with acpi and uniprocessor ioapic, Athlon etc. use the onboard nic, and try it with apic_tack=1 kernel arg.

Regards
Ross.

Transfered 1,8 GB without any crash. As the nvnet module seems to be part of the NVIDIA released drivers I use my Realtek 8139 (like before when I had the crashes). I just compiled the NVIDIA drivers and will give it a run. I am wondering where the actual bug might be located as you remember that I did not use APIC in the first place.

Thanx for help

Jens