2/11: actisys-sir: dongle api change

diff -u -p linux/drivers/net/irda.d6/actisys-sir.c  linux/drivers/net/irda/actisys-sir.c
@@ -65,7 +65,7 @@ static int actisys_reset(struct sir_dev 
 
 /* These are the baudrates supported, in the order available */
 /* Note : the 220L doesn't support 38400, but we will fix that below */
-static __u32 baud_rates[] = { 9600, 19200, 57600, 115200, 38400 };
+static unsigned baud_rates[] = { 9600, 19200, 57600, 115200, 38400 };
 
 #define MAX_SPEEDS (sizeof(baud_rates)/sizeof(baud_rates[0]))
 

@@ -118,7 +118,7 @@ static int actisys_open(struct sir_dev *
 {
 	struct qos_info *qos = &dev->qos;
 
-	dev->set_dtr_rts(dev, TRUE, TRUE);
+	sirdev_set_dtr_rts(dev, TRUE, TRUE);
 
 	/* Set the speeds we can accept */
 	qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;

@@ -130,13 +130,15 @@ static int actisys_open(struct sir_dev *
 	qos->min_turn_time.bits = 0x7f; /* Needs 0.01 ms */
 	irda_qos_bits_to_value(qos);
 
+	/* irda thread waits 50 msec for power settling */
+
 	return 0;
 }
 
 static int actisys_close(struct sir_dev *dev)
 {
 	/* Power off the dongle */
-	dev->set_dtr_rts(dev, FALSE, FALSE);
+	sirdev_set_dtr_rts(dev, FALSE, FALSE);
 
 	return 0;
 }

@@ -174,23 +176,25 @@ static int actisys_change_speed(struct s
 	 * Now, we can set the speed requested. Send RTS pulses until we
          * reach the target speed 
 	 */
-	for (i=0; i<MAX_SPEEDS; i++) {
+	for (i = 0; i < MAX_SPEEDS; i++) {
 		if (speed == baud_rates[i]) {
-			dev->speed = baud_rates[i];
+			dev->speed = speed;
 			break;
 		}
 		/* Set RTS low for 10 us */
-		dev->set_dtr_rts(dev, TRUE, FALSE);
+		sirdev_set_dtr_rts(dev, TRUE, FALSE);
 		udelay(MIN_DELAY);
 
 		/* Set RTS high for 10 us */
-		dev->set_dtr_rts(dev, TRUE, TRUE);
+		sirdev_set_dtr_rts(dev, TRUE, TRUE);
 		udelay(MIN_DELAY);
 	}
 
 	/* Check if life is sweet... */
-	if (i >= MAX_SPEEDS)
-		ret = -1;  /* This should not happen */
+	if (i >= MAX_SPEEDS) {
+		actisys_reset(dev);
+		ret = -EINVAL;  /* This should not happen */
+	}
 
 	/* Basta lavoro, on se casse d'ici... */
 	return ret;

@@ -221,11 +225,11 @@ static int actisys_change_speed(struct s
 static int actisys_reset(struct sir_dev *dev)
 {
 	/* Reset the dongle : set DTR low for 10 us */
-	dev->set_dtr_rts(dev, FALSE, TRUE);
+	sirdev_set_dtr_rts(dev, FALSE, TRUE);
 	udelay(MIN_DELAY);
 
 	/* Go back to normal mode */
-	dev->set_dtr_rts(dev, TRUE, TRUE);
+	sirdev_set_dtr_rts(dev, TRUE, TRUE);
 	
 	dev->speed = 9600;	/* That's the default */