Skip to contentSkip to conversation

Promise PDC20378 PATA support?

DISCUSSION Dan Hopper 2 participants 3 messages Feb 7, 2004 – Feb 11, 2004

lore
Share & tools
lore

Dan Hopper

author
#0 lore raw

Hi,

Has anyone had any luck getting PATA working on Promise PDC20378 controllers in a 2.6.x kernel? As far as I can determine from looking at the drivers and at 2-month old postings to linux-kernel, the sata_promise driver only handles the two SATA ports and not the PATA port. The Promise-supplied TX2plus driver works (with PATA support) for 2.4.x but hasn't been updated for 2.6.x.

I fear the answer is still no, but I hate being limited to only 4 PATA devices when I've got 5 sitting in there :)

Thanks,
Dan Hopper

#1 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 3 lines

Hi,

Has anyone had any luck getting PATA working on Promise PDC20378

If this is the controller that appears on motherboards like the MSI KT4 Ultra (Via KT400 chipset) then the PATA port works just fine in 2.4.x (x >= 22)

I'll have a dig in dmesg when I get home and find the relevant lines.

Mark.

- --
Mark Watts
Senior Systems Engineer
QinetiQ TIM
St Andrews Road, Malvern
GPG Public Key ID: 455420ED

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.3 (GNU/Linux)

iD8DBQFAKNsaBn4EFUVUIO0RAsppAKDU7QpIbt7RPWkhktikvMIIMZ9rugCeLRDV xYyYO0HsPitfnaiNKTF99h4=
=98Oy
-----END PGP SIGNATURE-----

#2 lore raw
In reply to Dan Hopper

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 3 lines

Hi,

Has anyone had any luck getting PATA working on Promise PDC20378

I lied - I have the PDC20376 not the 8 varient.

00:0d.0 RAID bus controller: Promise Technology, Inc. PDC20376 (rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 6620
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 96 (1000ns min, 4500ns max), cache line size 08
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at cc00 [size=64]
        Region 1: I/O ports at c800 [size=16]
        Region 2: I/O ports at c400 [size=128]
        Region 3: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at dffc0000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA 

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

During boot I see the following:

PROMISE SATA150 Series Linux Driver v1.00.0.10
pdc-ultra:[info] Drive 5: MAXTOR 6L020J1 40132502s 20548MB UDMA6
scsi0 : pdc-ultra
Vendor: Model: MAXTOR 6L020J1 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 4, lun 0 SCSI device sda: 40132503 512-byte hdwr sectors (20548 MB)
/dev/scsi/host0/bus0/target4/lun0: p1

Drive is a 20Gig Maxtor PATA device.

Cheers,

Mark.

- --
Mark Watts
Senior Systems Engineer
QinetiQ TIM
St Andrews Road, Malvern
GPG Public Key ID: 455420ED

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.3 (GNU/Linux)

iD8DBQFAKezgBn4EFUVUIO0RAr/vAKDICBtq9KoZ5ra/zRyKQnN3HU+mXACg094k 89yDB5lyez3+4WsAA3PWxFY=
=z3Gi
-----END PGP SIGNATURE-----