kernelparameter idex=noprobe
Hallo,
according to linux-2.6.4/Documentation/ide.txt :
"idex=noprobe" : do not attempt to access/use this interface
SuSEs inofficial 2.6.4-0 kernel ( precompiled from rpm) comes with CONFIG_BLK_DEV_SIIMAGE=yCONFIG_SCSI_SATA_SIL=m
Trying to use the sata_sil driver for my sil3112 controler I did give ide4=noprobe ide5=noprobe hdi=noprobe hdj=noprobe hdk=noprobe hdl=noprobe on the kernel commandline
The Bootup- messages show:
[...]
6>Using ACPI (MADT) for SMP configuration information
<4>Built 1 zonelists
<4>Kernel command line: root=/dev/hde2 vga=0x317 desktop hdc=ide-scsi hdclun=0 splash=silent 3
ide4=noprobe ide5=noprobe hdi=noprobe hdj=noprobe hdk=noprobe hdl=noprobe <6>ide_setup: hdc=ide-scsi
<6>ide_setup: hdclun=0
<6>bootsplash: silent mode.
<6>ide_setup: ide4=noprobe
<6>ide_setup: ide5=noprobe
<6>ide_setup: hdi=noprobe
<6>ide_setup: hdj=noprobe
<6>ide_setup: hdk=noprobe
<6>ide_setup: hdl=noprobe
[...]
6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>AMD7411: IDE controller at PCI slot 0000:00:07.1
<6>AMD7411: chipset revision 1
<6>AMD7411: not 100%% native mode: will probe irqs later <6>AMD7411: 0000:00:07.1 (rev 01) UDMA100 controller
<6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
<4>hda: DM166D DVD-ROM, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>hdc: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<6>PDC20270: IDE controller at PCI slot 0000:00:09.0
<6>PDC20270: chipset revision 2
<6>PDC20270: 100%% native mode on irq 177
<6> ide2: BM-DMA at 0x1830-0x1837, BIOS settings: hde:pio, hdf:pio
<6> ide3: BM-DMA at 0x1838-0x183f, BIOS settings: hdg:pio, hdh:pio
<4>hde: SAMSUNG SP0612N, ATA DISK drive
<4>ide2 at 0x1868-0x186f,0x1862 on irq 177
<6>SiI3112 Serial ATA: IDE controller at PCI slot 0000:00:0a.0 <6>SiI3112 Serial ATA: chipset revision 2
<6>SiI3112 Serial ATA: 100%% native mode on irq 185
<6> ide4: MMIO-DMA , BIOS settings: hdi:pio, hdj:pio
<6> ide5: MMIO-DMA , BIOS settings: hdk:pio, hdl:pio
<4>hde: max request size: 1024KiB
<6>hde: 117304992 sectors (60060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
<6> hde: hde1 < hde5 hde6 hde7 hde8 hde9 > hde2 hde3 hde4
[...]
Why is the SIL3112 taken over by the siimage driver ? Did I misinterpret ide.txt, is ide.txt wrong or is this a bug ?
hdi=noprobe seems to work however. The attached SATA disk doesn't show up. And it does show up if I leave out hdi=noprobe.
Is there any chance to use sata_sil with that kernel configuration ? Or is recompiling with CONFIG_BLK_DEV_SIIMAGE=m or with siimage disabled the only option ?
Quoted 57 lines · Markus Kossmann
Hallo,
according tolinux-2.6.4/Documentation/ide.txt:
"idex=noprobe" : do not attempt to access/use this interface
SuSEs inofficial 2.6.4-0 kernel ( precompiled from rpm) comes withCONFIG_BLK_DEV_SIIMAGE=yCONFIG_SCSI_SATA_SIL=mTrying to use the
sata_sildriver for my sil3112 controler I did give ide4=noprobe ide5=noprobe hdi=noprobe hdj=noprobe hdk=noprobe hdl=noprobe on the kernel commandlineThe Bootup- messages show:
[...]
6>Using ACPI (MADT) for SMP configuration information <4>Built 1 zonelists
<4>Kernel command line: root=/dev/hde2 vga=0x317 desktop hdc=ide-scsi hdclun=0 splash=silent 3
ide4=noprobe ide5=noprobe hdi=noprobe hdj=noprobe hdk=noprobe hdl=noprobe <6>ide_setup: hdc=ide-scsi
<6>ide_setup: hdclun=0
<6>bootsplash: silent mode.
<6>ide_setup: ide4=noprobe
<6>ide_setup: ide5=noprobe
<6>ide_setup: hdi=noprobe
<6>ide_setup: hdj=noprobe
<6>ide_setup: hdk=noprobe
<6>ide_setup: hdl=noprobe
[...]
6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>AMD7411: IDE controller at PCI slot 0000:00:07.1 <6>AMD7411: chipset revision 1
<6>AMD7411: not 100%% native mode: will probe irqs later <6>AMD7411: 0000:00:07.1 (rev 01) UDMA100 controller
<6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
<4>hda: DM166D DVD-ROM, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>hdc: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<6>PDC20270: IDE controller at PCI slot 0000:00:09.0 <6>PDC20270: chipset revision 2
<6>PDC20270: 100%% native mode on irq 177
<6> ide2: BM-DMA at 0x1830-0x1837, BIOS settings: hde:pio, hdf:pio
<6> ide3: BM-DMA at 0x1838-0x183f, BIOS settings: hdg:pio, hdh:pio
<4>hde: SAMSUNG SP0612N, ATA DISK drive
<4>ide2 at 0x1868-0x186f,0x1862 on irq 177
<6>SiI3112 Serial ATA: IDE controller at PCI slot 0000:00:0a.0 <6>SiI3112 Serial ATA: chipset revision 2
<6>SiI3112 Serial ATA: 100%% native mode on irq 185
<6> ide4: MMIO-DMA , BIOS settings: hdi:pio, hdj:pio
<6> ide5: MMIO-DMA , BIOS settings: hdk:pio, hdl:pio
<4>hde: max request size: 1024KiB
<6>hde: 117304992 sectors (60060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
<6> hde: hde1 < hde5 hde6 hde7 hde8 hde9 > hde2 hde3 hde4 [...]
Quoted 2 lines
Why is the SIL3112 taken over by the siimage driver ? Did I misinterpret ide.txt, is ide.txt wrong or is this a bug ?
It is not a bug - siimage driver is compiled in and PCI device is detected. It has nothing to do with "idex=noprobe" or "hdx=noprobe".
Quoted 6 lines
hdi=noprobe seems to work however. The attached SATA disk doesn't show up. And it does show up if I leave out hdi=noprobe.
Is there any chance to use
sata_silwith that kernel configuration ? Or is recompiling withCONFIG_BLK_DEV_SIIMAGE=mor with siimage disabled the only option ?
Yep.
Regards,
Bartlomiej
Booting off of IDE while using different libata drives on same southbridge
I am having a similar problem to what Markus Kossmann wrote about, but with the VIA Southbridge (Asus K8V). My situation is similar, but a little different. I would like to boot off a PATA drive attached to the Southbridge, but use libata for a couple SATA drives attached to the same Southbridge.
Is this still not possible? I also tried hde/hdg=noprobe options, but they didn't help the situation. It appears the only way to get the drives on sata_via is to boot off of them. Am I correct in thinking this is the only way to go about this?
-ryan
Quoted 11 lines · Bartlomiej Zolnierkiewicz
Quoted 5 lines
Is there any chance to use
sata_silwith that kernel configuration ? Or is recompiling withCONFIG_BLK_DEV_SIIMAGE=mor with siimage disabled the only option ?Yep.
Regards,
Bartlomiej
Re: Booting off of IDE while using different libata drives on same southbridge
Quoted 10 lines · J. Ryan Earl
I am having a similar problem to what Markus Kossmann wrote about, but with the VIA Southbridge (Asus K8V). My situation is similar, but a little different. I would like to boot off a PATA drive attached to the Southbridge, but use libata for a couple SATA drives attached to the same Southbridge.
Is this still not possible? I also tried hde/hdg=noprobe options, but they didn't help the situation. It appears the only way to get the drives on
sata_viais to boot off of them. Am I correct in thinking this is the only way to go about this?
Did you actually tried it (booting off of them)?
[ I can't see how this can help. ]
Just don't compile-in generic IDE PCI driver which controls your SATA drives (or don't load this module if you're using initrd).
Quoted 11 lines
-ryan
Quoted 8 lines · Bartlomiej Zolnierkiewicz
Quoted 3 lines
Is there any chance to use
sata_silwith that kernel configuration ? Or is recompiling withCONFIG_BLK_DEV_SIIMAGE=mor with siimage disabled the only option ?Yep.
Regards,
Bartlomiej
Re: Booting off of IDE while using different libata drives on same southbridge
Quoted 16 lines · Bartlomiej Zolnierkiewicz
Quoted 6 lines · J. Ryan Earl
I am having a similar problem to what Markus Kossmann wrote about, but with the VIA Southbridge (Asus K8V). My situation is similar, but a little different. I would like to boot off a PATA drive attached to the Southbridge, but use libata for a couple SATA drives attached to the same Southbridge.
Quoted 6 lines
Is this still not possible? I also tried hde/hdg=noprobe options, but they didn't help the situation. It appears the only way to get the drives on
sata_viais to boot off of them. Am I correct in thinking this is the only way to go about this?
Quoted 4 lines
Did you actually tried it (booting off of them)?
[ I can't see how this can help. ]
With libata linked into the kernel, and ide as a module, I can boot off of libata.
Quoted 4 lines
Just don't compile-in generic IDE PCI driver which controls your SATA drives (or don't load this module if you're using initrd).
As I said, I want to boot off of the PATA drives attached to the southbridge. To boot of them, I have to have the IDE driver compiled into the kernel; if I do this I can't use libata on that southbridge, the IDE driver take precedence for the serial ata channels.
-ryan
Re: Booting off of IDE while using different libata drives on same southbridge
Quoted 13 lines · you
Quoted 12 lines · Bartlomiej Zolnierkiewicz
Quoted 10 lines · J. Ryan Earl
I am having a similar problem to what Markus Kossmann wrote about, but with the VIA Southbridge (Asus K8V). My situation is similar, but a little different. I would like to boot off a PATA drive attached to the Southbridge, but use libata for a couple SATA drives attached to the same Southbridge.
Is this still not possible? I also tried hde/hdg=noprobe options, but they didn't help the situation. It appears the only way to get the drives on
sata_viais to boot off of them. Am I correct in thinking this is the only way to go about this?
Quoted 5 lines
Quoted 2 lines
Did you actually tried it (booting off of them)?
[ I can't see how this can help. ]With libata linked into the kernel, and ide as a module, I can boot off of libata.
Therefore you changed order in which these drivers are initialized, it has nothing to do with booting off of SATA drives.
Quoted 7 lines
Quoted 2 lines
Just don't compile-in generic IDE PCI driver which controls your SATA drives (or don't load this module if you're using initrd).
As I said, I want to boot off of the PATA drives attached to the southbridge. To boot of them, I have to have the IDE driver compiled into the kernel; if I do this I can't use libata on that southbridge, the IDE driver take precedence for the serial ata channels.
Just don't compile generic IDE PCI driver!!CONFIG_BLK_DEV_GENERIC=n
VIA PATA controller uses via82cxxx driver not generic IDE PCI one.
Quoted 1 line
-ryan
Re: Booting off of IDE while using different libata drives on same southbridge
Quoted 7 lines · Bartlomiej Zolnierkiewicz
Just don't compile generic IDE PCI driver!!
CONFIG_BLK_DEV_GENERIC=nVIA PATA controller uses via82cxxx driver not generic IDE PCI one.
Ahhh, I knew I was making a mistake. I didn't realize I was using the generic IDE driver.
Thank you sir!
-ryan