bcm5700 driver at 100Mbit? tg3 doesn't do 100Mbit - 2.6.4-mm1
tg3.ko loads, network starts up. Can't connect to 100Mbit network switch. The bcm5700 driver in ths SuSE kraxel 2.6.3 kernel works. The tg3 is supposed to be a replacement for bcm5700 I believe. Regards
Sid.
Signature · 2 lines
Sid Boyce .... Hamradio G3VBV and keen Flyer Linux Only Shop.
Quoted 3 lines · Sid Boyce
tg3.ko loads, network starts up. Can't connect to 100Mbit network switch. The bcm5700 driver in ths SuSE kraxel 2.6.3 kernel works. The tg3 is supposed to be a replacement for bcm5700 I believe.
On Debian's 2.4, I have been able to get 100 Mbps traffic by forcing a re-negotiation through mii-diag or ethtool (I don't recall which one, this mii-tool/mii-diag/ethtool is a HORRIBLE MESS that needs to be sorted out) and seem to recall that ifconfig eth0 down ; ifconfig eth1 up could also have fixed this - however, such behaviour is of course unsuitable for production use and I don't know if the same trick works on 2.6 kernels.
Signature · 3 lines
Matthias Andree Encrypt your mail: my GnuPG key ID is 0x052E7D95
Quoted 3 lines
Quoted 3 lines
tg3.ko loads, network starts up. Can't connect to 100Mbit network switch. The bcm5700 driver in ths SuSE kraxel 2.6.3 kernel works. The tg3 is supposed to be a replacement for bcm5700 I believe.
Works for me (Dell Latitude D600), both for "NIC to switch"...
===
Mar 12 16:20:37 y kernel: Linux version 2.6.4-mm1 (lech7@y) (gcc version 3.3.3) #1 Thu Mar 11 14:16:54 CET 2004 [...] Mar 12 16:20:37 y kernel: eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0d:56:7b:d8:9d [...] Mar 12 16:20:39 y kernel: tg3: eth0: Link is up at 100 Mbps, half duplex. Mar 12 16:20:39 y kernel: tg3: eth0: Flow control is off for TX and off for RX.
===
...and "NIC to NIC" mode:
===
Mar 14 03:43:08 y kernel: Linux version 2.6.4-mm1 (lech7@y) (gcc version 3.3.3) #1 Thu Mar 11 14:16:54 CET 2004 [...] Mar 14 03:43:08 y kernel: eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0d:56:7b:d8:9d [...] Mar 14 03:43:10 y kernel: tg3: eth0: Link is up at 100 Mbps, full duplex. Mar 14 03:43:10 y kernel: tg3: eth0: Flow control is off for TX and off for RX.
===
Signature · 4 lines
Leszek. -- [email protected] 2:480/33.7 -- REAL programmers use INTEGERS -- -- speaking just for myself...
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 6 lines · Ananda Bhattacharya
Yeah I had that problem so I just used the tg3 driver. The bcm5700 is actually made by broadcom, while the tg3 is somethting that tyan did for onboard ethernet chips, while the bcm5700 is for PCI cards.
So the bcm5700 should do the trick all in all :)
Thanks, I altered /etc/modprobe.conf, replacing bcm5700 with tg3, rebooted and it's OK. Regards
Sid.
Signature · 2 lines
Sid Boyce .... Hamradio G3VBV and keen Flyer Linux Only Shop.