Skip to contentSkip to conversation

2.4.25 XFS can't create files

DISCUSSION Carsten Gaebler 3 participants 4 messages Apr 2, 2004 – Apr 5, 2004

lore
Share & tools
lore
#0 lore raw

Hi there,

I have somewhat of an esoteric problem. I can create an XFS on an external fibre channel RAID attached to an LSI fibre channel card (Fusion MPT driver) but I can't create files or directories on that filesystem (Permission denied). ext2/ext3 work fine on the same partition, so I suspect this is an XFS+MPT issue.

Here's what I tried:

sq22:~# mkfs.xfs /dev/sdb2
meta-data=/dev/sdb2     isize=256    agcount=140, agsize=1048576 blks
data     =              bsize=4096   blocks=146320896, imaxpct=25
         =              sunit=0      swidth=0 blks, unwritten=0
naming   =version 2     bsize=4096
log      =internal log  bsize=4096   blocks=17861
realtime =none          extsz=65536  blocks=0, rtextents=0
sq22:~# mkdir /mnt/xfs
sq22:~# ls -ld / /mnt/ /mnt/xfs/
drwxr-xr-x   19 root     root         4096 Sep 16  2003 /
drwxr-xr-x    4 root     root         4096 Apr  2 09:26 /mnt/
drwxr-xr-x    2 root     root         4096 Apr  2 09:26 /mnt/xfs/
sq22:~# mount -t xfs /dev/sdb2 /mnt/xfs/
sq22:~# mount | grep xfs
/dev/sdb2 on /mnt/xfs type xfs (rw)
sq22:~# ls -ld /mnt/xfs/
drwxr-xr-x    2 root     root            6 Apr  2 09:25 /mnt/xfs/
sq22:~# touch /mnt/xfs/foo
touch: creating `/mnt/xfs/foo': Permission denied
sq22:~#

Here's some system information:

sq22:~# uname -a
Linux sq22 2.4.25 #3 SMP Fri Mar 19 14:39:04 CET 2004 i686 unknown
sq22:~# lsmod
Module                  Size  Used by    Not tainted
sg                     25092   0
mptscsih               33300   2
ipt_REJECT              3232  13  (autoclean)
iptable_filter          1792   1  (autoclean)
ip_tables              12288   2  [ipt_REJECT iptable_filter]
mptbase                33440   3  [mptscsih]
e1000                  64224   1
sq22:~#

From lspci:

03:08.0 Fibre Channel: LSI Logic / Symbios Logic (formerly NCR): Unknown device 0628
Subsystem: LSI Logic / Symbios Logic (formerly NCR): Unknown
device 5030
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR-

        Latency: 72 (16000ns min, 2500ns max), cache line size 10
        Interrupt: pin A routed to IRQ 24
        Region 0: I/O ports at 2000 [size=256]
        Region 1: Memory at fe6f0000 (64-bit, non-prefetchable) [size=64K]
        Region 3: Memory at fe6e0000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at fe500000 [disabled] [size=1M]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-

                Address: 0000000000000000  Data: 0000
        Capabilities: [68] #07 [0000]

From dmesg:

Fusion MPT base driver 2.05.11.03
Copyright (c) 1999-2003 LSI Logic Corporation
mptbase: Initiating ioc0 bringup
ioc0: FC919X: Capabilities={Initiator,Target,LAN}
mptbase: 1 MPT adapter found, 1 installed.
Fusion MPT SCSI Host driver 2.05.11.03
scsi1 : ioc0: LSIFC919X, FwRev=01000000h, Ports=1, MaxQ=1023, IRQ=24
blk: queue f7e21018, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: IFT Model: ES A08F-G Rev: 331J
Type: Direct-Access ANSI SCSI revision: 03
blk: queue f7b99e18, I/O limit 4294967295Mb (mask 0xffffffffffffffff) Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 SCSI device sdb: 2341134336 512-byte hdwr sectors (1198661 MB)
sdb: sdb1 sdb2
XFS mounting filesystem sd(8,18)
Ending clean XFS mount for filesystem: sd(8,18)

Any clues?

cg.

#1 lore raw

(cc-'d to the linux-xfs list)

Quoted 5 lines · Carsten Gaebler

I have somewhat of an esoteric problem. I can create an XFS on an external fibre channel RAID attached to an LSI fibre channel card (Fusion MPT driver) but I can't create files or directories on that filesystem (Permission denied). ext2/ext3 work fine on the same partition, so I suspect this is an XFS+MPT issue.

I suspect it's not MPT related. I'm not farmiliar with stock 2.4.25 but assume the XFS merge went OK and everything is sane. Any chance you can test with a CVS kernel from oss.sgi.com to rule out the (probably minor) differences there?

Quoted 2 lines
sq22:~# touch /mnt/xfs/foo
touch: creating `/mnt/xfs/foo': Permission denied

strace shows open/creat failing? there are also no ACLs and/or security modules involved are there?

#2 lore raw
Quoted 4 lines · Chris Wedgwood

I suspect it's not MPT related. I'm not farmiliar with stock 2.4.25 but assume the XFS merge went OK and everything is sane. Any chance you can test with a CVS kernel from oss.sgi.com to rule out the (probably minor) differences there?

The SGI kernel works fine. Thanks for the hint.

Quoted 1 line

strace shows open/creat failing?

Yes.

open("/mnt/xfs/foo", O_WRONLY|O_NONBLOCK|O_CREAT|O_NOCTTY|O_LARGEFILE, 0666) = -1 EACCES (Permission denied)

Quoted 2 lines

there are also no ACLs and/or
security modules involved are there?

Nope.

cg.

#3 lore raw
In reply to Carsten Gaebler
Quoted 7 lines · Carsten Gaebler

Hi there,

I have somewhat of an esoteric problem. I can create an XFS on an external fibre channel RAID attached to an LSI fibre channel card (Fusion MPT driver) but I can't create files or directories on that filesystem (Permission denied). ext2/ext3 work fine on the same partition, so I suspect this is an XFS+MPT issue.

Thats very odd - the SGI CVS 2.4 kernel (that you reported working) is also at 2.4.25, and there's nothing in the XFS fixes/updates there that might be the cause of this, AFAICT. ACLs are not in Marcelo's tree, but that is unlikely to be the cause here (both cases are well tested). The only other thing I can suggest is a liberal sprinkling of printks on the sys_open path, till you find the spot thats returning this error..

cheers.

Signature · 1 line
Nathan