PAT support
Hi Terence,
in your patch, you write
+/* Here is the PAT's default layout on ia32 cpus when we are done.
+ * PAT0: Write Back
+ * PAT1: Write Combine
+ * PAT2: Uncached
+ * PAT3: Uncacheable
+ * PAT4: Write Through
+ * PAT5: Write Protect
+ * PAT6: Uncached
+ * PAT7: Uncacheable
Is that layout possible?
There is an errata in the B2 and C1 stepping of the Pentium 4 cpus that results in incorrect PAT numbers: the highest bit is ignored by the CPU under some circumstances. There's a similar errata (E27) that affects all Pentium 3 cpus: The highest bit is always ignored. I think we need a fallback to 4 PAT entries.
--
Manfred
oh, good catch. we added comments detailing this to an internal evaluation stand-alone pat module for pci express testing (the same pat.c/pat.h files as a standalone module), and I forgot to propogate those comments to this patch.
here's a snippet of our comments:
/* Here is the PAT's default layout on ia32 cpus at boot/reset.
* This is table 10-12 in the IA-32 Intel Architecture Software Developer's
* Manual Volume 3: System Programming Guide.
* PAT0: Write Back
* PAT1: Write Through
* PAT2: Uncached (/ Uncacheable on Athlon cpus)
* PAT3: Uncacheable
* PAT4: Write Back
* PAT5: Write Through
* PAT6: Uncached (/ Uncacheable on Athlon cpus)
* PAT7: Uncacheable
*
* Rather than mucking with the PAT entries too much, we'll only replace one
* entry with Write Combining. Ideally, we'd do that to one of the latter 4
* entries, but due to errata in the P3/P4 cpus, we can only use the first
* four entries reliably.
*
* For that reason, we'll replace PAT1: Write Through with Write Combine. *
* For more details about these errata, see Intel Pentium III Processor
* Specification Update, errata E.27 (Upper Four PAT Entries Not Usable With
* Mode B or Mode C Paging) and Intel Pentium IV Processor Specification
* Update, errata N46 (PAT Index MSB May Be Calculated Incorrectly) */
rather than reprogramming all of the pats (compare the above table to the below table), we only replaced one entry with write-combining. I could just update cachemap with the corrected comments, or go ahead and only update the one pat entry, whichever everyone prefers.
Thanks,
Terence
Quoted 23 lines · On Mon, Apr 12, 2004 at 10:34:22PM -0700, [email protected] wrote:
Hi Terence,
in your patch, you write
+/* Here is the PAT's default layout on ia32 cpus when we are done.
+ * PAT0: Write Back
+ * PAT1: Write Combine
+ * PAT2: Uncached
+ * PAT3: Uncacheable
+ * PAT4: Write Through
+ * PAT5: Write Protect
+ * PAT6: Uncached
+ * PAT7: UncacheableIs that layout possible?
There is an errata in the B2 and C1 stepping of the Pentium 4 cpus that results in incorrect PAT numbers: the highest bit is ignored by the CPU under some circumstances. There's a similar errata (E27) that affects all Pentium 3 cpus: The highest bit is always ignored.
I think we need a fallback to 4 PAT entries.--
Manfred
Hi!
Quoted 11 lines
in your patch, you write
+/* Here is the PAT's default layout on ia32 cpus when we are done.
+ * PAT0: Write Back
+ * PAT1: Write Combine
+ * PAT2: Uncached
+ * PAT3: Uncacheable
+ * PAT4: Write Through
+ * PAT5: Write Protect
+ * PAT6: Uncached
+ * PAT7: Uncacheable
Quoted 6 lines
Is that layout possible?
There is an errata in the B2 and C1 stepping of the Pentium 4 cpus that results in incorrect PAT numbers: the highest bit is ignored by the CPU under some circumstances. There's a similar errata (E27) that affects all Pentium 3 cpus: The highest bit is always ignored. I think we need a fallback to 4 PAT entries.
What about arranging it so that foo is always more restrictive than foo|4? That way you can get some slowdowns on bad cpus, but it will always be correct.
Signature · 1 line
64 bytes from 195.113.31.123: icmp_seq=28 ttl=51 time=448769.1 ms
Quoted 13 lines · Manfred Spraul
Hi Terence,
in your patch, you write
+/* Here is the PAT's default layout on ia32 cpus when we are done.
+ * PAT0: Write Back
+ * PAT1: Write Combine
+ * PAT2: Uncached
+ * PAT3: Uncacheable
+ * PAT4: Write Through
+ * PAT5: Write Protect
+ * PAT6: Uncached
+ * PAT7: Uncacheable
Quoted 6 lines
Is that layout possible?
There is an errata in the B2 and C1 stepping of the Pentium 4 cpus that results in incorrect PAT numbers: the highest bit is ignored by the CPU under some circumstances. There's a similar errata (E27) that affects all Pentium 3 cpus:
The highest bit is always ignored.
I think we need a fallback to 4 PAT entries.
Write Through and Write Protect are essentially useless. So that should be easy to do.
Eric