Skip to contentSkip to conversation

Confused about 2.6 PnP support

DISCUSSION DervishD 2 participants 3 messages Apr 12, 2004 – Apr 15, 2004

lore
Share & tools
lore

DervishD

author
#0 lore raw

Hi all :)

I'm on the way of upgrading to 2.6.x kernel, and since I don't
have ISA cards (I don't even have an ISA bus in my mobo), I disabled ISA support in my config (CONFIG_ISA), but I've noticed that PnP support (CONFIG_PNP) depends on it :?

AFAIK, PnP, strictly speaking, has nothing to do with the PCI
bus, but I think is common notation to talk about PnP referring autoconfiguration of PCI cards, and I want to know if I need to select PCI support for having my PCI cards correctly detected and configured (currently my BIOS does the work), or if the PnP support in kernel 2.6 is just for ISA cards. In addition to this, the PnP BIOS support (which I think I may need so Linux correctly gets the IO, IRQ and DMA settings for my parallel port) is marked as EXPERIMENTAL (at least in 2.6.5)

I want to know if I must tell my BIOS I don't have a PnP OS or
if, on the contrary, I should tell my BIOS that my OS is not PnP (I only use Linux) and deselect PnP support (as well as ISA support) in my 2.6.x kernel. Personally, I don't mind setting 'Non PnP OS' in my BIOS and remove both CONFIG_ISA and CONFIG_PNP.

BTW, ¿does Linux support rebalancing of PnP bus resources or I
better avoid conflicts...?

Thanks a lot in advance :)

Raúl Núñez de Arenas Coronado

Signature · 2 lines
Linux Registered User 88736
http://www.pleyades.net & http://raul.pleyades.net/
#1 lore raw
Quoted 7 lines · DervishD

Hi all :)

I'm on the way of upgrading to 2.6.x kernel, and since I don't
have ISA cards (I don't even have an ISA bus in my mobo), I disabled ISA support in my config (CONFIG_ISA), but I've noticed that PnP support (CONFIG_PNP) depends on it :?

Quoted 9 lines

AFAIK, PnP, strictly speaking, has nothing to do with the PCI
bus, but I think is common notation to talk about PnP referring autoconfiguration of PCI cards, and I want to know if I need to select PCI support for having my PCI cards correctly detected and configured (currently my BIOS does the work), or if the PnP support in kernel 2.6 is just for ISA cards. In addition to this, the PnP BIOS support (which I think I may need so Linux correctly gets the IO, IRQ and DMA settings for my parallel port) is marked as EXPERIMENTAL (at least in 2.6.5)

In this context PnP is refering to configuration of system and ISA devices. PnPBIOS support should be safe but faults on boot for a few buggy systems. Because the recovery code has been fixed, this should be less of a problem. If you see a message indicating that a pnp device was activated as the parport driver loads then you need PnPBIOS support to properly use it. If not, then PnPBIOS will still aid in the device's detection process.

Quoted 6 lines

I want to know if I must tell my BIOS I don't have a PnP OS or
if, on the contrary, I should tell my BIOS that my OS is not PnP (I only use Linux) and deselect PnP support (as well as ISA support) in my 2.6.x kernel. Personally, I don't mind setting 'Non PnP OS' in my BIOS and remove both CONFIG_ISA and CONFIG_PNP.

If you are using PnPBIOS support then set PNP OS to "yes", otherwise use "no".

Quoted 3 lines

BTW, ?does Linux support rebalancing of PnP bus resources or I
better avoid conflicts...?

Yes, see sysfs and drivers/pnp/interface.c. Resources can be reallocated but only if the device is not bound to a driver (modules are useful for this).

Quoted 5 lines

Thanks a lot in advance :)

Ra?l N??ez de Arenas Coronado

Regards,
Adam

author
#2 lore raw

Hi Adam, and thanks for your answer :)

* Adam Belay <[email protected]> dixit:

Quoted 11 lines
Quoted 9 lines

AFAIK, PnP, strictly speaking, has nothing to do with the PCI
bus, but I think is common notation to talk about PnP referring autoconfiguration of PCI cards, and I want to know if I need to select PCI support for having my PCI cards correctly detected and configured (currently my BIOS does the work), or if the PnP support in kernel 2.6 is just for ISA cards. In addition to this, the PnP BIOS support (which I think I may need so Linux correctly gets the IO, IRQ and DMA settings for my parallel port) is marked as EXPERIMENTAL (at least in 2.6.5)

In this context PnP is refering to configuration of system and ISA devices.

But then, why it depends on ISA support?

BTW, in the case of my printer, the log says:

parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready

The question is that my parallel port is configured as EPP, using
DMA 3, not as SPP, and I'm not sure if the problem is on the kernel, the motherboard or if it is a simple matter of notation and the port is being properly detected. My /proc/sys/dev/parport says PCSPP,TRISTATE, not EPP... But DMA channel, IRQ line and IO addresses are being correctly detected, so this doesn't seem a problem of PnP.

Quoted 7 lines
Quoted 5 lines

I want to know if I must tell my BIOS I don't have a PnP OS or
if, on the contrary, I should tell my BIOS that my OS is not PnP (I only use Linux) and deselect PnP support (as well as ISA support) in my 2.6.x kernel. Personally, I don't mind setting 'Non PnP OS' in my BIOS and remove both CONFIG_ISA and CONFIG_PNP.

If you are using PnPBIOS support then set PNP OS to "yes", otherwise use "no".

So if I don't want ISA support in my kernel I must go with PNP OS
set to 'no' and let the BIOS do the work, am I right?

Quoted 5 lines
Quoted 2 lines

BTW, ?does Linux support rebalancing of PnP bus resources or I
better avoid conflicts...?

Yes, see sysfs and drivers/pnp/interface.c. Resources can be reallocated but only if the device is not bound to a driver (modules are useful for this).

Cool :)) Thanks for the information.

Raúl Núñez de Arenas Coronado

Signature · 2 lines
Linux Registered User 88736
http://www.pleyades.net & http://raul.pleyades.net/