ALI M5451 (CMI 9739): PCM always muted?
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22), snd_ali5451 loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).
Is this a known bug? Didn't have the time to check the code yet...
LLaP
bero
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 6 lines · Bernhard Rosenkraenzer
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),
snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).Is this a known bug? Didn't have the time to check the code yet...
There was a report that on a similar codec/controller combination such problem was caused by the "IEC958 Capture Monitor" switch turned on. Turning this switch off in alsamixer fixed the problem.
Hello Bernhard,
Bernhard Rosenkraenzer [Sat, Apr 17, 2004 at 07:45:35PM +0200]:
Quoted 4 lines
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware),
I don't really think so, as the version I had in my old Acer TM 524TEV allowed adjusting.
If no adjusting of pcm is available, howto adjust volume? Master doesn't affect any setting.
Quoted 2 lines
but doesn't make any noise -
apparently PCM is always muted (volume fixed at 0?).
Just unmute it with alsamixer, but it will raise volume to highest level.
Nico
Signature · 3 lines
Keep it simple & stupid, use what's available. pgp: 8D0E E27A | Nico Schottelius http://nerd-hosting.net | http://linux.schottelius.org
At Sat, 17 Apr 2004 19:45:35 +0200,
Quoted 6 lines · Bernhard Rosenkraenzer
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).
there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
Takashi
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 8 lines · Takashi Iwai
Quoted 5 lines
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
I knew that -- it doesn't make any sound even if it's unmuted though. Nothing useful in dmesg output either.
LLaP
bero
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 7 lines · Bernhard Rosenkraenzer
Quoted 6 lines · Takashi Iwai
Quoted 5 lines
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).
Quoted 5 lines
Quoted 2 lines
there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
I knew that -- it doesn't make any sound even if it's unmuted though. Nothing useful in dmesg output either.
And what does "amixer contents" show?
Quoted 7 lines · Sergey Vlasov
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),
snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).And what does "amixer contents" show?
numid=9,iface=MIXER,name='Master Mono Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=10,iface=MIXER,name='Master Mono Playback Volume'
; type=INTEGER,access=rw---,values=1,min=0,max=31,step=0 : values=31
numid=1,iface=MIXER,name='Master Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=2,iface=MIXER,name='Master Playback Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=31,step=0 : values=31,31
numid=26,iface=MIXER,name='PCM Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=7,iface=MIXER,name='Surround Playback Switch'
; type=BOOLEAN,access=rw---,values=2
: values=on,on
numid=8,iface=MIXER,name='Surround Playback Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=31,step=0 : values=31,31
numid=3,iface=MIXER,name='Center Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=4,iface=MIXER,name='Center Playback Volume'
; type=INTEGER,access=rw---,values=1,min=0,max=31,step=0 : values=0
numid=5,iface=MIXER,name='LFE Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=6,iface=MIXER,name='LFE Playback Volume'
; type=INTEGER,access=rw---,values=1,min=0,max=31,step=0 : values=0
numid=41,iface=MIXER,name='Line-In As Surround'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=18,iface=MIXER,name='Line Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=19,iface=MIXER,name='Line Playback Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=31,step=0 : values=0,0
numid=20,iface=MIXER,name='CD Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=21,iface=MIXER,name='CD Playback Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=31,step=0 : values=0,0
numid=17,iface=MIXER,name='Mic Boost (+20dB)'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=31,iface=MIXER,name='Mic Select'
; type=ENUMERATED,access=rw---,values=1,items=2 ; Item #0 'Mic1'
; Item #1 'Mic2'
: values=0
numid=15,iface=MIXER,name='Mic Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=16,iface=MIXER,name='Mic Playback Volume'
; type=INTEGER,access=rw---,values=1,min=0,max=31,step=0 : values=0
numid=13,iface=MIXER,name='Phone Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=14,iface=MIXER,name='Phone Playback Volume'
; type=INTEGER,access=rw---,values=1,min=0,max=31,step=0 : values=0
numid=22,iface=MIXER,name='Video Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=23,iface=MIXER,name='Video Playback Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=31,step=0 : values=0,0
numid=11,iface=MIXER,name='PC Speaker Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=12,iface=MIXER,name='PC Speaker Playback Volume'
; type=INTEGER,access=rw---,values=1,min=0,max=15,step=0 : values=0
numid=24,iface=MIXER,name='Aux Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=25,iface=MIXER,name='Aux Playback Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=31,step=0 : values=0,0
numid=30,iface=MIXER,name='Mono Output Select'
; type=ENUMERATED,access=rw---,values=1,items=2 ; Item #0 'Mix'
; Item #1 'Mic'
: values=0
numid=27,iface=MIXER,name='Capture Source'
; type=ENUMERATED,access=rw---,values=2,items=8 ; Item #0 'Mic'
; Item #1 'CD'
; Item #2 'Video'
; Item #3 'Aux'
; Item #4 'Line'
; Item #5 'Mix'
; Item #6 'Mix Mono'
; Item #7 'Phone'
: values=5,5
numid=28,iface=MIXER,name='Capture Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=29,iface=MIXER,name='Capture Volume'
; type=INTEGER,access=rw---,values=2,min=0,max=15,step=0 : values=0,0
numid=38,iface=MIXER,name='IEC958 Capture Valid Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=32,iface=MIXER,name='IEC958 Playback Con Mask'
; type=IEC958,access=r----,values=1
: values=?
numid=33,iface=MIXER,name='IEC958 Playback Pro Mask'
; type=IEC958,access=r----,values=1
: values=?
numid=36,iface=MIXER,name='IEC958 Playback AC97-SPSA'
; type=INTEGER,access=rw---,values=1,min=0,max=3,step=0 : values=3
numid=34,iface=MIXER,name='IEC958 Playback Default'
; type=IEC958,access=rw---,values=1
: values=?
numid=37,iface=MIXER,name='IEC958 Playback Source'
; type=ENUMERATED,access=rw---,values=1,items=2 ; Item #0 'Analog'
; Item #1 'Digital'
: values=0
numid=35,iface=MIXER,name='IEC958 Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=39,iface=MIXER,name='IEC958 Capture Monitor'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=40,iface=MIXER,name='IEC958 Capture Switch'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=42,iface=MIXER,name='External Amplifier'
; type=BOOLEAN,access=rw---,values=1
: values=on
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 7 lines · Bernhard Rosenkraenzer
Quoted 6 lines · Sergey Vlasov
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),
snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).
Quoted 8 lines
Quoted 1 line
And what does "amixer contents" show?
numid=35,iface=MIXER,name='IEC958 Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=39,iface=MIXER,name='IEC958 Capture Monitor'
; type=BOOLEAN,access=rw---,values=1
: values=on
Did you try to turn these things off?
Quoted 3 lines
numid=42,iface=MIXER,name='External Amplifier'
; type=BOOLEAN,access=rw---,values=1
: values=on
Or maybe this (who knows where it is hooked really).
At Wed, 21 Apr 2004 15:28:03 +0400,
Quoted 12 lines · Sergey Vlasov
[1 <text/plain; us-ascii (7bit)>]
Quoted 9 lines · Bernhard Rosenkraenzer
Quoted 7 lines · Sergey Vlasov
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),
snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).And what does "amixer contents" show?
Quoted 8 lines
Quoted 6 lines
numid=35,iface=MIXER,name='IEC958 Playback Switch'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=39,iface=MIXER,name='IEC958 Capture Monitor'
; type=BOOLEAN,access=rw---,values=1
: values=onDid you try to turn these things off?
yes 'iec958 capture monitor' should be off, at least.
Quoted 5 lines
Quoted 3 lines
numid=42,iface=MIXER,name='External Amplifier'
; type=BOOLEAN,access=rw---,values=1
: values=onOr maybe this (who knows where it is hooked really).
this should be on. (it's no longer 'power down' switch).
--
Takashi Iwai <[email protected]> ALSA Developer - www.alsa-project.org
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Takashi Iwai [Tue, Apr 20, 2004 at 12:39:35PM +0200]:
Quoted 11 lines
At Sat, 17 Apr 2004 19:45:35 +0200,
Quoted 6 lines · Bernhard Rosenkraenzer
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
Does that mean I have _no_ possibility to adjust the volume?
How do I find out if I got the CM9739? This is what lspci shows:
-------------------- snip ----------------
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Au dio Device (rev 02)
Subsystem: Elitegroup Computer Systems: Unknown device 0f22
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping
- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <M
Abort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at effac000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
-------------------- snap ----------------
Greetings,
Nico
Signature · 3 lines
Keep it simple & stupid, use what's available. pgp: 8D0E E27A | Nico Schottelius http://nerd-hosting.net | http://linux.schottelius.org
At Wed, 21 Apr 2004 14:04:54 +0200,
Quoted 12 lines · Nico Schottelius
[1 <text/plain; us-ascii (quoted-printable)>] Takashi Iwai [Tue, Apr 20, 2004 at 12:39:35PM +0200]:
Quoted 9 lines
At Sat, 17 Apr 2004 19:45:35 +0200,
Quoted 6 lines · Bernhard Rosenkraenzer
Hi,
On an ALI M5451 (Using a CMI 9739 - PCI ID 10b9:5451 Sub-ID 1019:0f22),snd_ali5451loads and can adjust mixer settings (except for PCM volume, but I think that's a limitation of the hardware), but doesn't make any noise - apparently PCM is always muted (volume fixed at 0?).
Quoted 4 lines
Quoted 2 lines
there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
Does that mean I have _no_ possibility to adjust the volume?
right. it doesn't support the PCM volume but you can basically adjust the master volume.
Quoted 1 line
How do I find out if I got the CM9739? This is what lspci shows:
you can see it in /proc/asound/card0/codec97#0/ac97#0-0.
Takashi
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Takashi Iwai [Wed, Apr 21, 2004 at 02:43:17PM +0200]:
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
Does that mean I have _no_ possibility to adjust the volume?
right. it doesn't support the PCM volume but you can basically adjust the master volume.
This doesn't affect the sound volume, tested it again some seconds ago. Some weeks ago I even tried it with _every_ switch available. I just can switch it on or off, but no volume adjusting.
And using master doesn't do anything at all.
Do you have any hint for me? Perhaps I am doing something wrong?
Quoted 3 lines
Quoted 1 line
How do I find out if I got the CM9739? This is what lspci shows:
you can see it in /proc/asound/card0/codec97#0/ac97#0-0.
For you information, perhaps you need it:
0-0/0: C-Media Electronics CMI9739
Capabilities : DAC resolution : 16-bit ADC resolution : 16-bit 3D enhancement : No 3D Stereo Enhancement
Current setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off
3D enhancement : off Loudness : off Mono output : MIX Mic select : Mic1
ADC/DAC loopback : off
Extended ID : codec=0 rev=1 LDAC SDAC CDAC DSA=0 SPDIF DRA
Extended status : SPCV LDAC SDAC CDAC SPDIF=3/4 SPDIF
SPDIF Control : Consumer PCM Category=0x2 Generation=1 Rate=48kHz
Have a nice day,
Nico
Signature · 3 lines
Keep it simple & stupid, use what's available. pgp: 8D0E E27A | Nico Schottelius http://nerd-hosting.net | http://linux.schottelius.org
Just wanted to ask whether someone read my mail and if anyone knows if there is the possibility to adjust sound volume or not.
Thanks for any answer/hint,
Nico
Nico Schottelius [Thu, Apr 22, 2004 at 12:00:31AM +0200]:
Quoted 51 lines
Takashi Iwai [Wed, Apr 21, 2004 at 02:43:17PM +0200]:
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
Does that mean I have _no_ possibility to adjust the volume?
right. it doesn't support the PCM volume but you can basically adjust the master volume.
This doesn't affect the sound volume, tested it again some seconds ago. Some weeks ago I even tried it with _every_ switch available. I just can switch it on or off, but no volume adjusting.
And using master doesn't do anything at all.
Do you have any hint for me? Perhaps I am doing something wrong?
Quoted 3 lines
Quoted 1 line
How do I find out if I got the CM9739? This is what lspci shows:
you can see it in /proc/asound/card0/codec97#0/ac97#0-0.
For you information, perhaps you need it:
0-0/0: C-Media Electronics CMI9739
Capabilities : DAC resolution : 16-bit ADC resolution : 16-bit 3D enhancement : No 3D Stereo EnhancementCurrent setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off3D enhancement : off Loudness : off Mono output : MIX Mic select : Mic1ADC/DAC loopback : off
Extended ID : codec=0 rev=1 LDAC SDAC CDAC DSA=0 SPDIF DRA
Extended status : SPCV LDAC SDAC CDAC SPDIF=3/4 SPDIF
SPDIF Control : Consumer PCM Category=0x2 Generation=1 Rate=48kHzHave a nice day,
Nico
Signature · 3 lines
Keep it simple & stupid, use what's available. pgp: 8D0E E27A | Nico Schottelius http://nerd-hosting.net | http://linux.schottelius.org
Signature · 3 lines
Keep it simple & stupid, use what's available. pgp: 8D0E E27A | Nico Schottelius http://nerd-hosting.net | http://linux.schottelius.org
Hi,
I have the same problem and haven't found a solution (yet).
Quoted 27 lines · Nico Schottelius
Just wanted to ask whether someone read my mail and if anyone knows if there is the possibility to adjust sound volume or not.
Thanks for any answer/hint,
Nico
Nico Schottelius [Thu, Apr 22, 2004 at 12:00:31AM +0200]:
Quoted 18 lines
Takashi Iwai [Wed, Apr 21, 2004 at 02:43:17PM +0200]:
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
there is no PCM volume on CM9739. it has only PCM mute switch. you can mute on/off via 'M' key of alsamixer.
Does that mean I have _no_ possibility to adjust the volume?
right. it doesn't support the PCM volume but you can basically adjust the master volume.
This doesn't affect the sound volume, tested it again some seconds ago. Some weeks ago I even tried it with _every_ switch available. I just can switch it on or off, but no volume adjusting.
And using master doesn't do anything at all.
Do you have any hint for me? Perhaps I am doing something wrong?
I got the same results, even when I set the soundchip registers "manually". I didn't find any register at all that changes the volume (apart from muting, that is).
CMedia's tech documents say that there is no PCM volume register (only PCM muting), but it also says that there _is_ a Master volume register. But changing this register has no effect. I guess it's a hardware bug then. Btw. CMedia's OSS driver does volume changing by calculating it inside the driver. Looks like they know the problem quite well :/
Until there's a CMI9739 driver for ALSA or a software volume changing plugin, this chip isn't very useful...
Oliver
Quoted 27 lines
Quoted 27 lines
Quoted 4 lines
Quoted 2 lines
How do I find out if I got the CM9739? This is what lspci shows:
you can see it in /proc/asound/card0/codec97#0/ac97#0-0.
For you information, perhaps you need it:
0-0/0: C-Media Electronics CMI9739
Capabilities : DAC resolution : 16-bit ADC resolution : 16-bit 3D enhancement : No 3D Stereo EnhancementCurrent setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off3D enhancement : off Loudness : off Mono output : MIX Mic select : Mic1ADC/DAC loopback : off
Extended ID : codec=0 rev=1 LDAC SDAC CDAC DSA=0 SPDIF DRA
Extended status : SPCV LDAC SDAC CDAC SPDIF=3/4 SPDIF
SPDIF Control : Consumer PCM Category=0x2 Generation=1 Rate=48kHz
Quoted 9 lines
Quoted 8 lines
Have a nice day,
Nico
Signature · 3 lines
Keep it simple & stupid, use what's available. pgp: 8D0E E27A | Nico Schottelius http://nerd-hosting.net | http://linux.schottelius.org
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click
Quoted 2 lines · Nico Schottelius
anyone knows if there is the possibility to adjust sound volume or not.
CMI hardware doesn't have this capability.
It would be possible to write a plugin that scales sound data in software before sending it to the device, but nobody has done this yet.
Regards,
Clemens
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click
Software volume via LADSPA and .asoundrc
Quoted 9 lines · Clemens Ladisch
Quoted 2 lines · Nico Schottelius
anyone knows if there is the possibility to adjust sound volume or not.
CMI hardware doesn't have this capability.
It would be possible to write a plugin that scales sound data in software before sending it to the device, but nobody has done this yet.
Install LADSPA, then try this in your .asoundrc ... adjust the "0.5" to taste.
Having it show up as an adjustable mixer control for runtime tuning would be even neater, of course.
pcm._volume {
type ladspa
slave.pcm "plughw:0,0";
path "/usr/local/lib/ladspa";
playback_plugins [
{
label amp_mono
input {
controls
[ 0.5 ]
}
}
]
}pcm.!default {
type plug
slave.pcm "_volume";
}--
Erik I. Bolsø | email: <knan at mo.himolde.no>
The UNIX philosophy basically involves giving you enough rope to hang yourself. And then a couple of feet more, just to be sure.
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id149&alloc_id�66&op=click