Skip to contentSkip to conversation

PPC Linux painic problem!

DISCUSSION jeffy 4 participants 4 messages Apr 26, 2004

lore
Share & tools
lore

jeffy

author
#0 lore raw

Hi all,
I hit on a problem about PPC Linux version 2.4.4 on a MPC855T board.
The kernel can start up ok normally, but when another PC continous sending UDP packets to it(about 8Mbps) when kernel is starting up, the kernel failed start up and printf the following messages:

.................................
.................................
.................................
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes

Oops: kernel access of bad area, sig: 11
NIP: C0095828 XER: C000057F LR: C0097804 SP: C01C7CA0 REGS: c01c7bf0 TRAP: 0300

MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: BF80F66F, DSISR: 0000000B
TASK = c01c6000[1] 'swapper' Last syscall: 120
last math 00000000 last altivec 00000000
GPR00: 00CC2222 C01C7CA0 C01C6000 C1F713F0 C0A82C60 C0A82C5D 00000000 C1DC3C00
GPR08: 00000002 00000000 00000200 BF80F5F3 FFFFFFFF 1004FCEC 01FDD000 007FFF0D
GPR16: 00000000 00000001 007FFF00 FFFFFFFF 00001032 001C7D40 00000000 C0002870
GPR24: 00000180 C00FD5C0 00000800 C1DC3C00 C0A82C5D 00000000 C1F713F0 C0A82C60 Call backtrace:
00000001 C0097804 C008D720 C0013BE4 C00028A0 C000EE10 C0106494 C01066EC C0106EA4 C00FE78C C00FE830 C00023CC C0004D68

Kernel panic: Aiee, killing interrupt handler!

In interrupt handler - not syncing
Rebooting in 180 seconds..

What's the problems? Is it a bug?
Best Regards!

Jeffy Guo
Bocom Digital Crop. Shanghai, China.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw

Jeffy,

Quoted 7 lines · jeffy

Hi all,
I hit on a problem about PPC Linux version 2.4.4 on a MPC855T board.
The kernel can start up ok normally, but when another PC
continous sending UDP packets to it(about 8Mbps) when kernel is starting up, the kernel failed start up and printf the following messages:

This is just a VERY wild guess: check the driver source (arch/ppc/8xx_io/fec.c in your case) and make sure the driver only forwards received packets to the IP stack when the interface is configured "UP". There once was a similar problem with the 826x driver.

Another reason could be that the FEC channel is not properly shut down by the firmware/bootloader before entering the kernel.

Next time try to add more information about your system, especially about the kernel and bootloader version you are using.

Regards,
Marius

--
Marius Groeger <[email protected]> Project Manager
SYSGO AG Embedded and Real-Time Software
Voice: +49 6136 9948 0 FAX: +49 6136 9948 10
www.sysgo.com | www.elinos.com | www.osek.de | www.imerva.com

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#2 lore raw
Quoted 24 lines · Marius Groeger

Jeffy,

Quoted 7 lines · jeffy

Hi all,
I hit on a problem about PPC Linux version 2.4.4 on a MPC855T board.
The kernel can start up ok normally, but when another PC
continous sending UDP packets to it(about 8Mbps) when kernel is starting up, the kernel failed start up and printf the following messages:

This is just a VERY wild guess: check the driver source (arch/ppc/8xx_io/fec.c in your case) and make sure the driver only forwards received packets to the IP stack when the interface is configured "UP". There once was a similar problem with the 826x driver.

Another reason could be that the FEC channel is not properly shut down by the firmware/bootloader before entering the kernel.

Next time try to add more information about your system, especially about the kernel and bootloader version you are using.

Quoted 14 lines

Regards,
Marius

--
Marius Groeger <[email protected]> Project Manager
SYSGO AG Embedded and Real-Time Software
Voice: +49 6136 9948 0 FAX: +49 6136 9948 10
www.sysgo.com | www.elinos.com | www.osek.de | www.imerva.com

If you use u-boot make sure you update to the latest version.

There was a bug with the fec not properly halting and then crashing the kernel when network traffic was present very early.

Regards

Pantelis

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#3 lore raw
In reply to Marius Groeger
Quoted 17 lines · Marius Groeger

Jeffy,

Quoted 7 lines · jeffy

Hi all,
I hit on a problem about PPC Linux version 2.4.4 on a MPC855T board.
The kernel can start up ok normally, but when another PC
continous sending UDP packets to it(about 8Mbps) when kernel is starting up, the kernel failed start up and printf the following messages:

This is just a VERY wild guess: check the driver source (arch/ppc/8xx_io/fec.c in your case) and make sure the driver only forwards received packets to the IP stack when the interface is configured "UP". There once was a similar problem with the 826x driver.

Quoted 8 lines

Another reason could be that the FEC channel is not properly shut down by the firmware/bootloader before entering the kernel.

Next time try to add more information about your system, especially about the kernel and bootloader version you are using.

Regards,
Marius

Hi all,

I think Marius' wild guess is correct! Until 5 minutes ago I had the same problem as Jeffy. My fix is to disable rx interrupts until fec_enet_open() is called. See the patch below. Thanks Marius.

BTW, the patch may not apply because of other changes to fec.c, so here's a description:
1st block: add int allow_rx to fec_enet_private struct 2nd block: set allow_rx in fec_enet_open()
3rd block: unset allow_rx in fec_enet_stop()
4th block: in fec_restart() only set IMASK[RXF] if allow_rx set

Alex

===================================================================
RCS file: /newcvs/ppc-linux/kernel/arch/ppc/8xx_io/fec.c,v retrieving revision 1.41

fec.c +5 -2
diff -u -r1.41 fec.c
@@ -220,6 +220,7 @@
 	struct	net_device_stats stats;
 	uint	tx_full;
 	spinlock_t lock;
+    int allow_rx;
 
 #ifdef	CONFIG_USE_MDIO
 	uint	phy_id;
@@ -1932,6 +1933,7 @@
 {
 	struct fec_enet_private *fep = dev->priv;
 
+    fep->allow_rx = 1;
 	/* I should reset the ring buffers here, but I don't yet know
 	 * a simple way to do that.
 	 */
@@ -1971,11 +1973,12 @@
 static int
 fec_enet_close(struct net_device *dev)
 {
+	struct fec_enet_private *fep = dev->priv;
 	/* Don't know what to do yet.
 	*/
 	netif_stop_queue(dev);
 	fec_stop(dev);
-
+    fep->allow_rx = 0;
 	return 0;
 }
 
@@ -2661,7 +2664,7 @@
 
 	/* Enable interrupts we wish to service.
 	*/
-	fecp->fec_imask = ( FEC_ENET_TXF | FEC_ENET_RXF | FEC_ENET_MII );
+	fecp->fec_imask = ( FEC_ENET_TXF | ((fep->allow_rx)?FEC_ENET_RXF:0) | FEC_ENET_MII );
 
 	/* And last, enable the transmit and receive processing.
 	*/

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/