remove comx drivers from tree

@@ -57,119 +57,6 @@
 	  The driver will be compiled as a module: the
 	  module will be called cosa.
 
-#
-# COMX drivers
-#
-# Not updated to 2.6.
-config COMX
-	tristate "MultiGate (COMX) synchronous serial boards support"
-	depends on WAN && (ISA || PCI) && BROKEN
-	---help---
-	  Drivers for the PC synchronous serial adapters by
-	  ITConsult-Pro Co, Hungary.
-
-	  Read <file:Documentation/networking/comx.txt> for help on configuring
-	  and using COMX interfaces. Further info on these cards can be found
-	  at <http://www.itc.hu/> or <[email protected]>.
-
-	  Say Y if you want to use any board from the MultiGate (COMX)
-	  family, you must also say Y to "/proc file system support"
-	  (CONFIG_PROC_FS) in order to use these drivers.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called comx.
-
-config COMX_HW_COMX
-	tristate "Support for COMX/CMX/HiCOMX boards"
-	depends on COMX
-	help
-	  Driver for the 'CMX', 'COMX' and 'HiCOMX' boards.
-
-	  You will need additional firmware to use these cards, which are
-	  downloadable from <ftp://ftp.itc.hu/>.
-
-	  Say Y if you have a board like this.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called comx-hw-comx.
-
-config COMX_HW_LOCOMX
-	tristate "Support for LoCOMX board"
-	depends on COMX
-	help
-	  Driver for the 'LoCOMX' board.
-
-	  Say Y if you have a board like this.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called comx-hw-locomx.
-
-config COMX_HW_MIXCOM
-	tristate "Support for MixCOM board"
-	depends on COMX
-	---help---
-	  Driver for the 'MixCOM' board.
-
-	  If you want to use the watchdog device on this card, you should
-	  select it in the Watchdog Cards section of the Character Devices
-	  configuration. The ISDN interface of this card is Teles 16.3
-	  compatible, you should enable it in the ISDN configuration menu. The
-	  driver for the flash ROM of this card is available separately on
-	  <ftp://ftp.itc.hu/>.
-
-	  Say Y if you have a board like this.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called comx-hw-mixcom.
-
-config COMX_HW_MUNICH
-	tristate "Support for MUNICH based boards: SliceCOM, PCICOM (WelCOM)"
-	depends on COMX
-	---help---
-	  Driver for the 'SliceCOM' (channelized E1) and 'PciCOM' (X21) boards.
-
-	  Read <file:Documentation/networking/slicecom.txt> for help on
-	  configuring and using SliceCOM interfaces. Further info on these
-	  cards can be found at <http://www.itc.hu> or <[email protected]>.
-
-	  Say Y if you have a board like this.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called comx-hw-munich.
-
-config COMX_PROTO_PPP
-	tristate "Support for HDLC and syncPPP protocols on MultiGate boards"
-	depends on COMX
-	help
-	  Cisco-HDLC and synchronous PPP protocol driver.
-
-	  Say Y if you want to use either protocol.
-
-	  To compile this as a module, choose M here: the
-	  module will be called comx-proto-ppp.
-
-config COMX_PROTO_LAPB
-	tristate "Support for LAPB protocol on MultiGate boards"
-	depends on WAN && (COMX!=n && LAPB=m && LAPB || LAPB=y && COMX)
-	help
-	  LAPB protocol driver.
-
-	  Say Y if you want to use this protocol.
-
-	  To compile this as a module, choose M here: the
-	  module will be called comx-proto-lapb.
-
-config COMX_PROTO_FR
-	tristate "Support for Frame Relay on MultiGate boards"
-	depends on COMX
-	help
-	  Frame Relay protocol driver.
-
-	  Say Y if you want to use this protocol.
-
-	  To compile this as a module, choose M here: the
-	  module will be called comx-proto-fr.
-
 config DSCC4
 	tristate "Etinc PCISYNC serial board support"
 	depends on WAN && PCI && m

@@ -32,14 +32,6 @@
 
 obj-$(CONFIG_HOSTESS_SV11)	+= z85230.o	syncppp.o	hostess_sv11.o
 obj-$(CONFIG_SEALEVEL_4021)	+= z85230.o	syncppp.o	sealevel.o
-obj-$(CONFIG_COMX)		+= 				comx.o
-obj-$(CONFIG_COMX_HW_COMX)	+= 				comx-hw-comx.o
-obj-$(CONFIG_COMX_HW_LOCOMX)	+= z85230.o	syncppp.o	comx-hw-locomx.o
-obj-$(CONFIG_COMX_HW_MIXCOM)	+=				comx-hw-mixcom.o
-obj-$(CONFIG_COMX_HW_MUNICH)	+=				comx-hw-munich.o
-obj-$(CONFIG_COMX_PROTO_PPP)	+=		syncppp.o	comx-proto-ppp.o
-obj-$(CONFIG_COMX_PROTO_LAPB)	+=				comx-proto-lapb.o
-obj-$(CONFIG_COMX_PROTO_FR)	+=				comx-proto-fr.o
 obj-$(CONFIG_COSA)		+=		syncppp.o	cosa.o
 obj-$(CONFIG_FARSYNC)		+=		syncppp.o	farsync.o
 obj-$(CONFIG_DSCC4)             +=				dscc4.o