Multiple (ICH3) IDE-controllers in a system
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 10 lines · Linux Kernel Mailing List
ChangeSet 1.1627, 2004/05/15 09:42:40-07:00, [email protected]
[PATCH] Multiple (ICH3) IDE-controllers in a system
This fixes a problem with multiple IDE controllers in a system.
The problem is that
pcibios_fixupstable (inarch/i386/pci/fixup.c) uses thepci_fixup_ide_trash()quirk for Intel's ICH3 (my case specifically 8086:248b). This clears any bogus BAR information set up by the BIOS.
Quoted 7 lines
In a system which has multiple ICH3's can't use any of the IDE controllers beside the one on the first ICH3.
Anyhow, the fix is to make sure
pci_fixup_ide_trashresets the BARs only for first time being called, so the subsequent IDE controllers will use the BIOS BARs. This is better than "loosing" all these IDE controllers in the case their BARs set right.
I do not think this is correct.
The programming interface register tells us if we're in legacy or native mode, which is what this fixup is concerned with, AFAICS.
So, the code should base its actions on whether or not the controller is in legacy mode, _not_ ordering.
Jeff
Jeff,
Here is what I see: pci_scan_single_device() at
http://lxr.linux.no/source/drivers/pci/probe.c?v=2.6.5#L590 which calls to pci_fixup_device() (line 601) which in turn use the quirks table at
http://lxr.linux.no/source/arch/i386/pci/fixup.c?v=2.6.5#L190 (my chipset is in line 248). The quirks table for ICH3 use pci_fixup_ide_trash()at
http://lxr.linux.no/source/arch/i386/pci/fixup.c?v=2.6.5#L90 - this reset the BARs for the device. Resetting the all (4) BARs of (ICH3) IDE controllers will cause them to use the defaults BARs (0x170, 0x1f0) in ide_hwif_configure() at
http://lxr.linux.no/source/drivers/ide/setup-pci.c?v=2.6.5#L420. This will fail with any subsequent (ICH3) IDE controllers (two devices can't use the same ports).
Agree or not?
My patch (not sure there is nicer way to handle this), will not allow reset of BARs if you hit any ICH3 which is not the first one. This will rely on BIOS setting for all other controllers.
--Shai
-----Original Message-----
From: Jeff Garzik [mailto:[email protected]]
Sent: Saturday, May 15, 2004 11:57
To: Linux Kernel Mailing List
Cc: [email protected]; Bartlomiej Zolnierkiewicz; Andrew Morton
Subject: Re: [PATCH] Multiple (ICH3) IDE-controllers in a system
Quoted 7 lines · Linux Kernel Mailing List
ChangeSet 1.1627, 2004/05/15 09:42:40-07:00, [email protected]
[PATCH] Multiple (ICH3) IDE-controllers in a system
This fixes a problem with multiple IDE controllers in a system.
The problem is that
pcibios_fixupstable (inarch/i386/pci/fixup.c)
uses
Quoted 1 line
the
pci_fixup_ide_trash()quirk for Intel's ICH3 (my case
specifically
Quoted 1 line
8086:248b). This clears any bogus BAR information set up by the
BIOS.
Quoted 5 lines
In a system which has multiple ICH3's can't use any of the IDE controllers beside the one on the first ICH3.
Anyhow, the fix is to make sure
pci_fixup_ide_trashresets the BARs
only
Quoted 1 line
for first time being called, so the subsequent IDE controllers will
use
Quoted 1 line
the BIOS BARs. This is better than "loosing" all these IDE
controllers
Quoted 1 line
in the case their BARs set right.
I do not think this is correct.
The programming interface register tells us if we're in legacy or native mode, which is what this fixup is concerned with, AFAICS.
So, the code should base its actions on whether or not the controller is in legacy mode, _not_ ordering.
Jeff