priorities + htb
Hi!
How does prioritization work when you've got a tree structure, e.g.
|
+-- class_a rate 64kbit prio 1 | | | +-- class_a1 rate 32kbit prio 1 | | | `-- class_a2 rate 32kbit prio 2 |
`-- class_b rate 64kbit prio 2
Above could either be interpreted as
(a) a, a1 have prio 1
b, a2 have prio 2
(iow, no distinction is being made between the inner/nested classes and
the outer/parent classes)
OR
(b) all packets matching a1, a2 are prio 1, then a1 is given a higher priority than a2
(iow, multiple layers of prioritization exist)
Signature · 16 lines
Regards
Abraham
TODAY the Pond!
TOMORROW the World!
-- Frogs (1972)
___________________________________________________
Abraham vd Merwe - Frogfoot Networks CC
1st Floor, Albion Springs, 183 Main Road, Newlands
Phone: +27 21 689 3876 Cell: +27 82 565 4451
Http: http://www.frogfoot.net/ Email: [email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/Quoted 6 lines · Abraham van der Merwe
Hi!
How does prioritization work when you've got a tree structure, e.g.
I think the whole idea of linux QOS is that it dequeues up the tree until it reaches the net interface. So effectively I think you evaluate each leaf in turn on the way up the tree
If for example you have some queue which gives 50:50, and below one leaf you add another queue which gives 50:50 then I think those bottom leaves are getting 1/4 each.
I'm sure Andy or someone else will correct me if I'm wrong, but I think this is how you evaluate the whole QOS tree to see what will happen?
Ed W
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
U¿ytkownik Abraham van der Merwe napisa³:
Quoted 10 lines
Hi!
How does prioritization work when you've got a tree structure, e.g.
|+-- class_a rate 64kbit prio 1 | | | +-- class_a1 rate 32kbit prio 1 | | | `-- class_a2 rate 32kbit prio 2 |`--
class_brate 64kbit prio 2
HTB means: __Hierarchical__ Token Bucket so it is more like this:
Quoted 5 lines
(b) all packets matching a1, a2 are prio 1, then a1 is given a higher priority than a2
(iow, multiple layers of prioritization exist)
But "prio" is used when there is some some unused BW that could be splited for borrowing (for classes which have ceil higher than rate). -josh
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 11 lines · pljosh
U¿ytkownik Abraham van der Merwe napisa³:
Quoted 10 lines
Hi!
How does prioritization work when you've got a tree structure, e.g.+--
class_arate 64kbit prio 1| +-- class_a1 rate 32kbit prio 1 | | `-- class_a2 rate 32kbit prio 2`--
class_brate 64kbit prio 2
The prio of class class_a is never used and does not matter.
Quoted 8 lines
HTB means:
__Hierarchical__Token Bucket so it is more like this:Quoted 4 lines
(b) all packets matching a1, a2 are prio 1, then a1 is given a higher priority than a2
(iow, multiple layers of prioritization exist)
But "prio" is used when there is some some unused BW that could be splited for borrowing (for classes which have ceil higher than rate).
Htb is used for 2 things:
- class with lowest prio will get the lowest latancy (if and only if this class is not sending more data then the tate)
- class will lowest prio will get the remaining bandwidth from the parent after each child class is sending his rate.
Stef
Signature · 6 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/