Skip to contentSkip to conversation

tc+mrtg

LARTC Kristiadi Himawan 8 participants 9 messages Jul 19, 2004 – Aug 19, 2004

lore
Share & tools
lore
#0 lore raw

Hi,

I'm sorry if this question already asked by someone else.
My question is how to make mrtg graph for traffic that already shape by htb. Acctually i already have mrtg for it but the traffic captured was before the shaper (PREROUTING and POSTROUTING)
so the bandwidth shown is not the real traffic.
So what should i do if i want to see graph traffic that passing through my shaper.

Thanks for the help.

Regards,

Kris

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

MRTG can only show interface load, basicaly it is the graphic representation
of what you will see with ifconfig.

For more advanced graph you need to use another software than mrtg.

----- Original Message -----
From: "Kristiadi Himawan" <[email protected]>
To: <[email protected]>
Sent: Monday, July 19, 2004 1:42 PM
Subject: [LARTC] tc+mrtg

Quoted 4 lines

Hi,

I'm sorry if this question already asked by someone else.
My question is how to make mrtg graph for traffic that already shape by

htb.

Quoted 1 line

Acctually i already have mrtg for it but the traffic captured was before

the

Quoted 7 lines

shaper (PREROUTING and POSTROUTING)
so the bandwidth shown is not the real traffic.
So what should i do if i want to see graph traffic that passing through my shaper.

Thanks for the help.

Quoted 8 lines

Regards,

Kris

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Kristiadi Himawan
Quoted 4 lines · Roy

MRTG can only show interface load, basicaly it is the graphic representation
of what you will see with ifconfig.

For more advanced graph you need to use another software than mrtg.

MRTG can graph any variable that you can read using SNMP. The problem is getting the tc stats readable using SNMP, that's the trick bit (which as far as I've seen can't be done, but I hope I'm wrong).

Gideon

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Kristiadi Himawan
Quoted 5 lines · Gideon le Grange
Quoted 3 lines · Roy

MRTG can only show interface load, basicaly it is the graphic representation of what you will see with ifconfig.

Quoted 7 lines
Quoted 1 line

For more advanced graph you need to use another software than mrtg.

MRTG can graph any variable that you can read using SNMP. The problem is getting the tc stats readable using SNMP, that's the trick bit (which as far as I've seen can't be done, but I hope I'm wrong).

MRTG doesn't necessarily need SNMP, you can feed it ANY value via a perl script. I've been doing it for ages. You just need to get at the values (peridoic tc -s qdisc show, parse it, feed mrtg)

From : http://people.ee.ethz.ch/~oetiker/webtools/mrtg/mrtg-reference.html

"External Monitoring Scripts
If you want to monitor something which does not provide data via
snmp you can use some external program to do the data gathering.

The external command must return 4 lines of output:

Line 1
current state of the first variable, normally 'incoming bytes count'

Line 2
current state of the second variable, normally 'outgoing bytes count'

Line 3
string (in any human readable format), telling the uptime of the
target.

Line 4
string, telling the name of the target.

Depending on the type of data your script returns you might want to use the 'gauge' or 'absolute' arguments for the Options keyword.

Example:

Target[ezwf]: /usr/local/bin/df2mrtg /dev/dsk/c0t2d0s0

Note the use of the backticks (`), not apostrophes (') around the command.

If you want to use a backtick in the command name this can be done but you must escape it with a backslash ...

If your script does not have any data to return but does not want mrtg to complain about invalid data, it can return 'UNKNOWN' instead of a number. Note though that only rrdtool is realy equipped to handle unknown data well.
"

Signature · 6 lines
C U

      - -- ---- ----- -----/\/  René Gallati  \/\---- ----- --- -- -
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to Kristiadi Himawan

A good tool that I use to graoh things is netmrg, www.netmrg.net

[]s.

Quoted 53 lines · Rene Gallati
Quoted 5 lines · Gideon le Grange
Quoted 3 lines · Roy

MRTG can only show interface load, basicaly it is the graphic representation of what you will see with ifconfig.

Quoted 7 lines
Quoted 1 line

For more advanced graph you need to use another software than mrtg.

MRTG can graph any variable that you can read using SNMP. The problem is getting the tc stats readable using SNMP, that's the trick bit (which as far as I've seen can't be done, but I hope I'm wrong).

MRTG doesn't necessarily need SNMP, you can feed it ANY value via a perl script. I've been doing it for ages. You just need to get at the values (peridoic tc -s qdisc show, parse it, feed mrtg)

From : http://people.ee.ethz.ch/~oetiker/webtools/mrtg/mrtg-reference.html

"External Monitoring Scripts
If you want to monitor something which does not provide data via
snmp you can use some external program to do the data gathering.

The external command must return 4 lines of output:

Line 1
current state of the first variable, normally 'incoming bytes count'

Line 2
current state of the second variable, normally 'outgoing bytes count'

Line 3
string (in any human readable format), telling the uptime of the
target.

Line 4
string, telling the name of the target.

Depending on the type of data your script returns you might want to use the 'gauge' or 'absolute' arguments for the Options keyword.

Example:

Target[ezwf]: /usr/local/bin/df2mrtg /dev/dsk/c0t2d0s0

Note the use of the backticks (`), not apostrophes (') around the command.

If you want to use a backtick in the command name this can be done but you must escape it with a backslash ...

If your script does not have any data to return but does not want mrtg to complain about invalid data, it can return 'UNKNOWN' instead of a number. Note though that only rrdtool is realy equipped to handle unknown data well. "

Signature · 23 lines
_______________________________________________

Alessandro Ren

	

*/ OpServices
Luciana de Abreu, 471 - Sala 403
Porto Alegre, RS - CEP 90570-060/*

* (*   phone 55(51)3061-3588
* 4*/ /    fax 55(51)3061-3588

	

* Q*   mobile 55(51)9807-3255
* :*   email [email protected] <mailto:[email protected]>

_______________________________________________

"Esta mensagem é endereçada exclusivamente à(s) pessoa(s) e/ou instituições acima indicadas e pode conter informações confidenciais, particulares ou privilegiadas, as quais não podem, sob qualquer forma ou pretexto, ser utilizadas, divulgadas, alteradas, impressas ou copiadas, total ou parcialmente, por pessoas não autorizadas. No caso desta mensagem ser recebida por erro, por favor, providencie sua exclusão do sistema, notificando o remetente imediatamente. Eventual erro de transmissão desta mensagem em nenhuma hipótese constituirá renúncia à confidencialidade ou a qualquer direito ou prerrogativa daí decorrente."

"This message is intended only for the named person's and/or entity's use and may contain confidential, proprietary or legally privileged information, which shall not be used, disclosed, changed, printed or copied, in whole or in part, by not intended recipients. If this message is received by error, please delete it from your system and notify the sender, immediately. No confidentiality or privilege is waived by any mistransmission."
#5 lore raw
In reply to Kristiadi Himawan

HTB + IMQ + SNMPD + MRTG
IMQ made its own interface as shown when you typed "ifconfig" So you'll be able to graph just as you graph using the real interface ..

- Rio.Martin -

Quoted 12 lines · Roy

MRTG can only show interface load, basicaly it is the graphic representation of what you will see with ifconfig.
For more advanced graph you need to use another software than mrtg.

----- Original Message -----
From: "Kristiadi Himawan" <[email protected]>
To: <[email protected]>
Sent: Monday, July 19, 2004 1:42 PM
Subject: [LARTC] tc+mrtg

Quoted 2 lines

Hi,

Quoted 20 lines
Quoted 2 lines

I'm sorry if this question already asked by someone else.
My question is how to make mrtg graph for traffic that already shape by

htb.

Quoted 1 line

Acctually i already have mrtg for it but the traffic captured was before

the

Quoted 11 lines

shaper (PREROUTING and POSTROUTING)
so the bandwidth shown is not the real traffic.
So what should i do if i want to see graph traffic that passing through my shaper.

Thanks for the help.

Regards,

Kris

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#6 lore raw
In reply to Kristiadi Himawan

I already use external script that fetch iptables mangle table from PREROUTING and POSTROUTING counter.
But the traffic isn't really accurate, i found when there's bulk UDP traffic come to the shaper, my mrtg shown that
the traffic shown bigger than allocated bandwidth for that class. So the question, it's possible to make script from tc command,
that count bandwith acctually passing through the shaper.

Regards,

Kris
----- Original Message -----
From: "Rene Gallati" <[email protected]>
To: <[email protected]>
Cc: <[email protected]>
Sent: Monday, July 19, 2004 8:47 PM
Subject: Re: [LARTC] tc+mrtg

Quoted 3 lines · Gideon le Grange
Quoted 1 line · Roy

MRTG can only show interface load, basicaly it is the graphic

representation

Quoted 9 lines
Quoted 3 lines

of what you will see with ifconfig.

For more advanced graph you need to use another software than mrtg.

MRTG can graph any variable that you can read using SNMP. The problem is getting the tc stats readable using SNMP, that's the trick bit (which as far as I've seen can't be done, but I hope I'm wrong).

MRTG doesn't necessarily need SNMP, you can feed it ANY value via a perl script. I've been doing it for ages. You just need to get at the values (peridoic tc -s qdisc show, parse it, feed mrtg)

From : http://people.ee.ethz.ch/~oetiker/webtools/mrtg/mrtg-reference.html

"External Monitoring Scripts
If you want to monitor something which does not provide data via
snmp you can use some external program to do the data gathering.

The external command must return 4 lines of output:

Line 1
current state of the first variable, normally 'incoming bytes count'

Line 2
current state of the second variable, normally 'outgoing bytes count'

Line 3
string (in any human readable format), telling the uptime of the
target.

Line 4
string, telling the name of the target.

Depending on the type of data your script returns you might want to use the 'gauge' or 'absolute' arguments for the Options keyword.

Example:

Target[ezwf]: /usr/local/bin/df2mrtg /dev/dsk/c0t2d0s0

Note the use of the backticks (`), not apostrophes (') around the command.

If you want to use a backtick in the command name this can be done but you must escape it with a backslash ...

If your script does not have any data to return but does not want mrtg to complain about invalid data, it can return 'UNKNOWN' instead of a number. Note though that only rrdtool is realy equipped to handle unknown data well.
"

Signature · 10 lines
C U

      - -- ---- ----- -----/\/  René Gallati  \/\---- ----- --- -- -
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#7 lore raw
In reply to Kristiadi Himawan
Quoted 7 lines · Kristiadi Himawan

I already use external script that fetch iptables mangle table from PREROUTING and POSTROUTING counter.
But the traffic isn't really accurate, i found when there's bulk UDP traffic come to the shaper, my mrtg shown that
the traffic shown bigger than allocated bandwidth for that class. So the question, it's possible to make script from tc command,
that count bandwith acctually passing through the shaper.

You can patch snmp so you can get the tc counters and process them in a custom script or use mrtg:
http://www.docum.org/docum.org/tc-snmp/

Stef

Signature · 6 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#8 lore raw
In reply to Kristiadi Himawan

I can't seem to find tcrrd2.pl on the site.

Quoted 14 lines · Stef Coene
Quoted 7 lines · Kristiadi Himawan

I already use external script that fetch iptables mangle table from PREROUTING and POSTROUTING counter.
But the traffic isn't really accurate, i found when there's bulk UDP traffic come to the shaper, my mrtg shown that
the traffic shown bigger than allocated bandwidth for that class. So the question, it's possible to make script from tc command,
that count bandwith acctually passing through the shaper.

You can patch snmp so you can get the tc counters and process them in a custom script or use mrtg:
http://www.docum.org/docum.org/tc-snmp/

Stef

Quoted 8 lines

--
[email protected]
"Using Linux as bandwidth manager"

     http://www.docum.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/