Skip to contentSkip to conversation

wan/cycx_drv: replace schedule_timeout()

PATCH New Nishanth Aravamudan 1 participant 1 message Jul 27, 2004

Subsystems (2)
Network drivers Kernel janitors
lore
Share & tools
lore

Nishanth Aravamudan

author
#0 lore raw

PATCH 1/1 wan/cycx_drv: replace schedule_timeout()

I would appreciate any comments from the janitors list. This is one (of many) cases where I made a decision about replacing

set_current_state(TASK_INTERRUPTIBLE);
schedule_timeout(some_time);

with

msleep(jiffies_to_msecs(some_time));

msleep() is not exactly the same as the previous code, but I only did this replacement where I thought long delays were *desired*. If this is not the case here, then just disregard this patch.

Thanks,
Nish

Applys-to: 2.6.7

Description: Replace delay_cycx() with msleep() to guarantee the task delays for the desired time. Remove definition of delay_cycx().

Signed-off-by Nishanth Aravamudan <[email protected]>
drivers/net/wan/cycx_drv.c +7 -15
@@ -74,7 +74,6 @@ static int reset_cyc2x(void *addr);
 static int detect_cyc2x(void *addr);
 
 /* Miscellaneous functions */
-static void delay_cycx(int sec);
 static int get_option_index(long *optlist, long optval);
 static u16 checksum(u8 *buf, u32 len);
 

@@ -260,7 +259,7 @@ static int memory_exists(void *addr)
 			if (readw(addr + 0x10) == TEST_PATTERN)
 				return 1;
 
-		delay_cycx(1);
+		msleep(1000);
 	}
 
 	return 0;

@@ -317,7 +316,7 @@ static void cycx_reset_boot(void *addr, 
 
 	/* 80186 was in hold, go */
 	writeb(0, addr + START_CPU);
-	delay_cycx(1);
+	msleep(1000);
 }
 
 /* Load data.bin file through boot (reset) interface. */

@@ -463,13 +462,13 @@ static int load_cyc2x(struct cycx_hw *hw
 		cycx_reset_boot(hw->dpmbase, reset_image, img_hdr->reset_size);
 		/* reset is waiting for boot */
 		writew(GEN_POWER_ON, pt_cycld);
-		delay_cycx(1);
+		msleep(1000);
 
 		for (j = 0 ; j < 3 ; j++)
 			if (!readw(pt_cycld))
 				goto reset_loaded;
 			else
-				delay_cycx(1);
+				msleep(1000);
 	}
 
 	printk(KERN_ERR "%s: reset not started.\n", modname);

@@ -496,7 +495,7 @@ reset_loaded:
 
 	/* Arthur Ganzert's tip: wait a while after the firmware loading...
 	   seg abr 26 17:17:12 EST 1999 - acme */
-	delay_cycx(7);
+	msleep(7000);
 	printk(KERN_INFO "%s: firmware loaded!\n", modname);
 
 	/* enable interrupts */

@@ -548,20 +547,13 @@ static int get_option_index(long *optlis
 static int reset_cyc2x(void *addr)
 {
 	writeb(0, addr + RST_ENABLE);
-	delay_cycx(2);
+	msleep(2000);
 	writeb(0, addr + RST_DISABLE);
-	delay_cycx(2);
+	msleep(2000);
 
 	return memory_exists(addr);
 }
 
-/* Delay */
-static void delay_cycx(int sec)
-{
-	set_current_state(TASK_INTERRUPTIBLE);
-	schedule_timeout(sec * HZ);
-}
-
 /* Calculate 16-bit CRC using CCITT polynomial. */
 static u16 checksum(u8 *buf, u32 len)
 {

_______________________________________________
Kernel-janitors mailing list
[email protected]
http://lists.osdl.org/mailman/listinfo/kernel-janitors