HDD LED doesn't light.
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
I seem to remember hearing somewhere that some or all of the Silicon Image SATA chips have to control the HDD activity light output by twiddling some GPIO outputs in the driver, it's not inherently done in the hardware as with most controllers..
----- Original Message ----- From: "Fernando O. Korndörfer" <[email protected]>
Newsgroups: fa.linux.kernel
To: "Ben Skeggs" <[email protected]>
Cc: <[email protected]>
Sent: Tuesday, August 24, 2004 7:10 AM
Subject: Re: HDD LED doesn't light.
Quoted 28 lines
This seems to be a hardware problem, as I have similar hardware (Asus A7N8x-e deluxe) and the HDD Led also stays off. BTW, I'm using MS-Windows(R).
Tell me something, you'r using SATA, right?
Quoted 20 lines · Ben Skeggs
Hello,
No matter how much harddisk activity is occuring on my system, the harddisk LED stays off. At first I thought I'd misconnected the lead, but under Windows the light is functional.
This occurs on both my SATA harddisk and my PATA harddisk.
SATA controller: Silicon Image sil3112
PATA controller: NForce2
Motherboard : Abit NF7-S 2.0
CPU : AthlonXP 3000+The earliest kernel I've used with this hardware is 2.6.6, and the problem occurs right up to 2.6.8.1.
I'm completely clueless as I was under the impression that the hardware controlled the LED.
Could I please be CC'd any replies as I'm not subscribed to the list.
Regards,
Ben Skeggs
-
Just an FYI... historically, the LED has been driven in PATA with a signal known as /DASP, this is an active-low signal called "Drive Active / Slave Present" and a PATA drive asserts this signal when processing a command.
If I understand it right, in SATA, instead of a wire-based protocol, we have a serialized packet-based protocol, so there was no driving of an LED in the initial specification. Revisions to the specification have since commandeered one of the pins on the power connector for use as a /DASP signal to drive an LED. However, to do that you obviously can't be using a MOLEX->SATA power adapter, you need a motherboard that natively supports SATA. The 3112 you mention attempts to be a native SATA solution, it doesn't act merely as a PATA->SATA converter.
Therefore, they may not have done the DASP- signal internally.
Another option would be one of the new 4+ port SATA RAID adapters that has LEDs on the adapter board itself.
Quoted 56 lines · Robert Hancock
I seem to remember hearing somewhere that some or all of the Silicon Image SATA chips have to control the HDD activity light output by twiddling some GPIO outputs in the driver, it's not inherently done in the hardware as with most controllers..
----- Original Message -----
From: "Fernando O. Korndörfer" <[email protected]>
Newsgroups: fa.linux.kernel
To: "Ben Skeggs" <[email protected]>
Cc: <[email protected]>
Sent: Tuesday, August 24, 2004 7:10 AM
Subject: Re: HDD LED doesn't light.Quoted 4 lines
This seems to be a hardware problem, as I have similar hardware (Asus A7N8x-e deluxe) and the HDD Led also stays off.
BTW, I'm using MS-Windows(R).Quoted 29 lines
Tell me something, you'r using SATA, right?
Quoted 24 lines · Ben Skeggs
Hello,
No matter how much harddisk activity is occuring on my system, the harddisk LED stays off. At first I thought I'd misconnected the lead, but under Windows the light is functional.
This occurs on both my SATA harddisk and my PATA harddisk.
SATA controller: Silicon Image sil3112
PATA controller: NForce2
Motherboard : Abit NF7-S 2.0
CPU : AthlonXP 3000+The earliest kernel I've used with this hardware is 2.6.6, and the problem occurs right up to 2.6.8.1.
I'm completely clueless as I was under the impression that the hardware controlled the LED.
Could I please be CC'd any replies as I'm not subscribed to the list.
Regards,
Ben Skeggs
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines
Just an FYI... historically, the LED has been driven in PATA with a signal known as /DASP, this is an active-low signal called "Drive Active / Slave Present" and a PATA drive asserts this signal when processing a command.
Quoted 13 lines
If I understand it right, in SATA, instead of a wire-based protocol, we have a serialized packet-based protocol, so there was no driving of
an LED in the initial specification. Revisions to the specification have since commandeered one of the pins on the power connector for use
as a /DASP signal to drive an LED. However, to do that you obviously
can't be using aMOLEX->SATApower adapter, you need a motherboard that natively supports SATA. The 3112 you mention attempts to be a native SATA solution, it doesn't act merely as aPATA->SATAconverter.
Therefore, they may not have done the DASP- signal internally.
But this doesn't explain why I have two motherboards here where the HDD activity LED does not light up in linux (for SATA drives) but does in windows . Note that it only starts working in windows *after* the driver has loaded. One is an ASUS A7N8X Deluxe (rev 1.0) and the other an Abit NF7-S (rev 2.0), both with Sil3112 controllers. On the other hand, I have a DFI Ultra Infinity with a Sil3114 whose activity LED works fine in linux.
Adrian
Quoted 4 lines · Adrian Yee
But this doesn't explain why I have two motherboards here where the HDD activity LED does not light up in linux (for SATA drives) but does in windows . Note that it only starts working in windows *after* the driver has loaded.
I've heard of implementations of the drive light on SATA where it is controlled through a general-purpose I/O pin somewhere else in the chipset. If that's the case, then the Windows driver may well know how to drive the GPIO to indicate drive activity for you...
Signature · 4 lines
Matt Domsch Sr. Software Engineer, Lead Engineer Dell Linux Solutions linux.dell.com & www.dell.com/linux Linux on Dell mailing lists @ http://lists.us.dell.com
Quoted 10 lines · Matt Domsch
Quoted 4 lines · Adrian Yee
But this doesn't explain why I have two motherboards here where the HDD activity LED does not light up in linux (for SATA drives) but does in windows . Note that it only starts working in windows *after* the driver has loaded.
I've heard of implementations of the drive light on SATA where it is controlled through a general-purpose I/O pin somewhere else in the chipset. If that's the case, then the Windows driver may well know how to drive the GPIO to indicate drive activity for you...
That would be my guess too.
This is all part of the initial hiccups in a brand new interface. Within another year or two, everything will stabilize out and work "as intended" (crosses fingers)
--eric