Skip to contentSkip to conversation

HCDP concerns

DISCUSSION Xavier Bru 3 participants 5 messages Sep 1, 2004 – Sep 3, 2004

lore
Share & tools
lore

Xavier Bru

author
#0 lore raw

Hello Bjorn and all,

I have some concerns with using kernel 2.6.8.1 (and 2.6.7) with our platform that has a new BIOS that provides HCDP.

1) When kernel is configured without h/pcdp support ( CONFIG_EFI_PCDP is not set),
the serial console are not initialized (efi.hcdp is not NULL).

A simple fix could be:
--- linux-2.6.8.1-ori/arch/ia64/kernel/setup.c 2004-08-14
12:54:50.000000000 +0200
+++ linux-2.6.8.1/arch/ia64/kernel/setup.c 2004-08-31
11:54:02.000000000 +0200
@@ -351,9 +351,9 @@
#endif

 #ifdef CONFIG_EFI_PCDP
     efi_setup_pcdp_console(*cmdline_p);

+ if (!efi.hcdp)
#endif
#ifdef CONFIG_SERIAL_8250_CONSOLE
- if (!efi.hcdp)

         setup_serial_legacy();

#endif

2) Our platform has 2 serial ports (let say port 0 at address 3f8, port 1 at address 2f8). Usually port 0 is seen as ttyS0 & port 1 as ttyS1. EFI console redirection is done on port S1 (2f8) & is described through HCDP(port 0 is not described).
Using the h/pcdp support ( CONFIG_EFI_PCDP=1), we get some strange behaviours:
. "console=ttyS0" boot parameter, as explained in menuconfig takes the HCDP table entry as console, but changes the ttyS* order:
ttyS1 for port 0 (3f8) and ttyS0 for port 1 (2f8). Console is OK, but the ttyS0 on port 1 is confusing compared to kernels without hcdp support. . due to this behaviour, there is no more possibility to have the linux console redirection on the port 0 at boot time.
. My understanding was that h/pcdp support should provide some new consoleïi (or serial) option to have the console defined by efi used by linux as console, but that this should not change the ttyS order, and that we should still be able to use console="ttySx" at boot time to have the console on port "x".
. specifying no "console=" provides no console as the Conout variable is not exported by EFI at runtime. Should it be ?

Thanks in advance for your clarifications.
Xavier

Signature · 8 lines
 Sincères salutations.
_____________________________________________________________________
 
Xavier BRU                 BULL ISD/R&D/INTEL office:     FREC B1-422
tel : +33 (0)4 76 29 77 45                    http://www-frec.bull.fr
fax : +33 (0)4 76 29 77 70                 mailto:[email protected]
addr: BULL, 1 rue de Provence, BP 208, 38432 Echirolles Cedex, FRANCE
_____________________________________________________________________
#1 lore raw
Quoted 2 lines · Xavier Bru

I have some concerns with using kernel 2.6.8.1 (and 2.6.7) with our platform that has a new BIOS that provides HCDP.

Great! I'm thrilled that non-HP boxes are starting to provide the HCDP! If there's still time to change, you might consider implementing the PCDP, as it is significantly improved.

Quoted 3 lines

1) When kernel is configured without h/pcdp support ( CONFIG_EFI_PCDP is not set),
the serial console are not initialized (efi.hcdp is not NULL).

I'm not quite sure what the problem is here. Were you hoping that even without CONFIG_EFI_PCDP, we would notice that efi_uart_console_only() is true, and just default to a serial console? That would be nice, but I don't think the EFI console path contains enough information to directly locate the UART device early in boot (In general, you need PCI enumeration or ACPI namespace access to interpret device paths.)

Quoted 6 lines

A simple fix could be:
--- linux-2.6.8.1-ori/arch/ia64/kernel/setup.c 2004-08-14
12:54:50.000000000 +0200
+++ linux-2.6.8.1/arch/ia64/kernel/setup.c 2004-08-31
11:54:02.000000000 +0200

Review line 358

Quoted 9 lines
(quoted diff) +1 -1
@@ -351,9 +351,9 @@
 #endif
 #ifdef CONFIG_EFI_PCDP
     efi_setup_pcdp_console(*cmdline_p);
+    if (!efi.hcdp)
 #endif
 #ifdef CONFIG_SERIAL_8250_CONSOLE
-    if (!efi.hcdp)
         setup_serial_legacy();
 #endif

The "assume ports are at 0x3f8 and 0x2f8" approach is dangerous (because we'll poke at things that might not exist), and I don't want to do any more of that than we have to.

My expectation is that CONFIG_EFI_PCDP would always be enabled; I'm not aware of any downside to that, even if the platform doesn't supply an HCDP or PCDP.

Quoted 10 lines

2) Our platform has 2 serial ports (let say port 0 at address 3f8, port 1 at address 2f8). Usually port 0 is seen as ttyS0 & port 1 as ttyS1. EFI console redirection is done on port S1 (2f8) & is described through HCDP(port 0 is not described).
Using the h/pcdp support ( CONFIG_EFI_PCDP=1), we get some strange behaviours:
. "console=ttyS0" boot parameter, as explained in menuconfig takes the HCDP table entry as console, but changes the ttyS* order:
ttyS1 for port 0 (3f8) and ttyS0 for port 1 (2f8). Console is OK, but the ttyS0 on port 1 is confusing compared to kernels without hcdp support.

Yes, I agree this is broken. The ttySx device names should stay the same, regardless of whether PCDP is present, or whether we look at it.

I posted patches to fix this a long time ago, but it involved too many changes to the serial driver. I have some ideas about how to improve this, so your interest will prod me to pursue them.

Quoted 2 lines

. due to this behaviour, there is no more possibility to have the linux console redirection on the port 0 at boot time.

I don't understand what this is. Can you explain further?

Quoted 5 lines

. My understanding was that h/pcdp support should provide some new consoleïi (or serial) option to have the console defined by efi used by linux as console, but that this should not change the ttyS order, and that we should still be able to use console="ttySx" at boot time to have the console on port "x".

If your BIOS supplies a PCDP and you set CONFIG_EFI_PCDP, you should not have to use a "console=" option at all.

Even if you only have an HCDP, you don't have to use a "console=" option if ConOut contains only UARTs and you're using the default baud rate. We'll just default to the first HCDP entry.

Quoted 2 lines

. specifying no "console=" provides no console as the Conout variable is not exported by EFI at runtime. Should it be ?

I think it makes sense that ConOut should be available for runtime access, but I can't point to a reference in the spec. All the platforms I've seen do make it available for runtime access.

We currently look at ConOut only when we have an HCDP. If the BIOS supplies a PCDP, there's no need to look at ConOut.

#2 lore raw
In reply to Xavier Bru
Quoted 9 lines
Quoted 1 line

. specifying no "console=" provides no console as the Conout

variable is

Quoted 1 line

not exported by EFI at runtime. Should it be ?

I think it makes sense that ConOut should be available for runtime access,
but I can't point to a reference in the spec. All the platforms I've seen
do make it available for runtime access.

Yep, ConOut is one of the globally defined variables that has visibility in pre-boot space as well as during runtime. Check out the attributes for ConOut in section 3.2 of the EFI spec.

matt

#3 lore raw
In reply to Xavier Bru
Quoted 4 lines · Xavier Bru

No, I just meant that without CONFIG_EFI_PCDP, we need to fall back to the standart initialization calling setup_serial_legacy().  Without the patch, the test on efi.hcdp returns non zero, and the setup_serial_legacy is not called.

The only benefit of setup_serial_legacy() is that that a serial console can start working earlier. If you don't call it, the serial console will still work after the normal serial driver initializes.

Quoted 4 lines

In our case, the EFI has access to 1 serial line, but there are 2 serials in the machine, and we used to use the linux console on one or the other serial. Only one line is described in the HCDP (the one of the EFI redirection).

This sounds broken. If you have an HCDP and you want to use an early serial console, the HCDP should describe the port you want to use.

If one of the ports is for use by EFI only, there's no point in describing that port in the HCDP.

Quoted 11 lines

I still have some problem of understanding if HCDP should provide information on all potential consoles, or should provide information on the consoles that EFI effectively uses.

In the first case, we need still an information on which linux will use (the "console= ").

In the second case, the "console=" could allow using others possible consoles to linux, as linux gave this flexibility before using the HCDP.  But it is maybe sufficient to consider that linux consoles are same as efi consoles.

My goal is certainly to make Linux automatically use the same console as EFI used. That is complicated a bit by the fact that EFI can use multiple devices simultaneously, without any concept of a "primary" device. Linux really wants a single device. (You can use multiple "console=" arguments to get kernel output on several devices, but eventually init is going to open a single device.)

One of the big problems with the HCDP was that it could describe several UARTs, but there was no indication of which was the primary. So Linux only looks at the first entry. This is one of the things the PCDP is intended to fix.

Let me restate this to see if I understand what you need:

I think you have ports at 0x3f8 and 0x2f8. The desired naming is 0x3f8 = ttyS0 and 0x2f8 = ttyS1.

With CONFIG_EFI_PCDP=n, you should get the desired naming, and "console=ttyS0" or "console=ttyS1" should both work and go to the correct ports (but the output won't start until the serial driver initializes).

With CONFIG_EFI_PCDP=y, the first port in the HCDP becomes ttyS0. (This is a bug and I'll try to fix it soon.) "console=ttyS0" should work, the output should start early, and it should go to the first device in the HCDP. "console=ttyS1" should also work, but the output won't start until later, and it should go to the other port (the one that is NOT described first in the HCDP).

I think what you want is a way to
(1) get early output, and
(2) specify the port where the output should go
That's perfectly reasonable, but neither scenario above gives you that.

Rather than using the hack of assuming ports at 0x3f8 and 0x2f8, I'd like to use this as an excuse to get the cleaner solution done. I'm thinking something like a "console=serial,0x3f8" argument to specify the device. Then we don't have to bind a name to the device, so we get rid of the renaming problem. And the HCDP/PCDP will become just a default source of the "0x3f8" information if it's not on the command line.

Would that solve the problem?

author
#4 lore raw
In reply to Xavier Bru
Quoted 4 lines · Bjorn Helgaas

Let me restate this to see if I understand what you need:

Quoted 9 lines

I think you have ports at 0x3f8 and 0x2f8. The desired naming is 0x3f8 = ttyS0 and 0x2f8 = ttyS1.

With CONFIG_EFI_PCDP=n, you should get the desired naming, and "console=ttyS0" or "console=ttyS1" should both work and go to the correct ports (but the output won't start until the serial driver initializes).

Yes, but I also want to be able to have the boot traces when system does not boot, and also have an
early kdb prompt.

Quoted 8 lines

With CONFIG_EFI_PCDP=y, the first port in the HCDP becomes ttyS0. (This is a bug and I'll try to fix it soon.) "console=ttyS0" should work, the output should start early, and it should go to the first device in the HCDP. "console=ttyS1" should also work, but the output won't start until later, and it should go to the other port (the one that is NOT described first in the HCDP).

yes, but currently our 1rst (and only one) HCDP entry is 2f8, and console=ttyS1 gives
also the same serial (2f8). This is why I was looking for the previous ttyS0 semantic (3f8).

Quoted 14 lines

I think what you want is a way to
(1) get early output, and
(2) specify the port where the output should go
That's perfectly reasonable, but neither scenario above gives you that.

Rather than using the hack of assuming ports at 0x3f8 and 0x2f8, I'd like to use this as an excuse to get the cleaner solution done. I'm thinking something like a "console=serial,0x3f8" argument to specify the device. Then we don't have to bind a name to the device, so we get rid of the renaming problem. And the HCDP/PCDP will become just a default source of the "0x3f8" information if it's not on the command line.

Quoted 3 lines

Would that solve the problem?

Yes, it sounds good. In our case we keep our H/PCDP describing where is directed the EFI console, that provides the default console for linux, and we still have the possibility to override at boot time to go to another console.
Thanks a lot for looking in deep to my problem.
Xavier

Quoted 7 lines

-
To unsubscribe from this list: send the line "unsubscribe linux-ia64" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 8 lines
 Sincères salutations.
_____________________________________________________________________
 
Xavier BRU                 BULL ISD/R&D/INTEL office:     FREC B1-422
tel : +33 (0)4 76 29 77 45                    http://www-frec.bull.fr
fax : +33 (0)4 76 29 77 70                 mailto:[email protected]
addr: BULL, 1 rue de Provence, BP 208, 38432 Echirolles Cedex, FRANCE
_____________________________________________________________________