Time runs exactly three times too fast
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success.
It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).
All my applications (KDE, command "date"...) runs three times too fast. It's very annoying.
My /dev/cpuinfo :
presario:~# cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 15 model : 12 model name : AMD Athlon(tm) XP Processor 3000+ stepping : 0 cpu MHz : 266.127 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmovpat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext 3dnowext 3dnow bogomips : 517.12
My config file for my kernel is here:
http://romain.webzzanine.net/linux/myconfig-2.6.8.1
Please help me :)
Romain Moyne
Quoted 4 lines · Romain Moyne
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
Quoted 8 lines
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success.
It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).All my applications (KDE, command "date"...) runs three times too fast. It's very annoying.
Can you try this without cpuspeed or some frequency control daemon running? So disable it in runlevel scripts and then reboot.
Is it just me or the bogomips rating listed there completely out of whack?
I'll note however I don't have a kernel 2.6 box lying anywhere nearby, but I shouldn't have thought the way the bogomips rating is counted would have changed.
Anyhoo my understanding is that bogomips are used for timing in a few obscure circumstances -- maybe this could be causing the problems? (I would have though about 10x higher would be more correct)
--Oliver Hunt
Quoted 26 lines · Zwane Mwaikambo
Quoted 4 lines · Romain Moyne
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
Quoted 8 lines
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success.
It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).All my applications (KDE, command "date"...) runs three times too fast. It's very annoying.
Can you try this without cpuspeed or some frequency control daemon running? So disable it in runlevel scripts and then reboot.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 1 line · Oliver Hunt
Is it just me or the bogomips rating listed there completely out of whack?
Yes it is, you'll also note that the cpu clock frequency is also low, hence my suspicion of cpufreq, which would affect general timing.
Quoted 7 lines · Zwane Mwaikambo
Quoted 1 line · Oliver Hunt
Is it just me or the bogomips rating listed there completely out of whack?
Yes it is, you'll also note that the cpu clock frequency is also low, hence my suspicion of cpufreq, which would affect general timing.
Oops, I hadn't noticed that :)
Perhaps one of the cpu specific options in the config? Sadly I can't remember what options there are, and the last 2.6 kernel compile I did was with 2.6.3 or 4 so there may be new options, but I can't think of anything that could conceivably cause weirdness in the clock speed detection...
--Oliver
Le Mercredi 01 Septembre 2004 14:15, Zwane Mwaikambo a écrit :
Quoted 12 lines · Romain Moyne
Quoted 11 lines
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success. It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).
Quoted 5 lines
Quoted 2 lines
All my applications (KDE, command "date"...) runs three times too fast. It's very annoying.
Can you try this without cpuspeed or some frequency control daemon running? So disable it in runlevel scripts and then reboot.
I have not cpuspeed or some frequency control daemon running. I just have this:
presario:/etc/rc2.d# ls S10sysklogd S20alsa S20makedev S20xprint S99kdm S99xdm S11klogd S20exim4 S20pcmcia S89atd S99rmnologin S14ppp S20inetd S20xfs S89cron S99stop-bootlogd presario:/etc/rc2.d#
Quoted 5 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines · Romain Moyne
presario:/etc/rc2.d# ls S10sysklogd S20alsa S20makedev S20xprint S99kdm S99xdm S11klogd S20exim4 S20pcmcia S89atd S99rmnologin S14ppp S20inetd S20xfs S89cron S99stop-bootlogd presario:/etc/rc2.d#
Please send a dmesg and .config
Le Mercredi 01 Septembre 2004 14:35, Zwane Mwaikambo a écrit :
Quoted 8 lines · Romain Moyne
Quoted 5 lines
presario:/etc/rc2.d# ls S10sysklogd S20alsa S20makedev S20xprint S99kdm S99xdm S11klogd S20exim4 S20pcmcia S89atd S99rmnologin S14ppp S20inetd S20xfs S89cron S99stop-bootlogd presario:/etc/rc2.d#Please send a dmesg and .config
presario:/sys/devices/system/cpu/cpu0# dmesg
Linux version 2.6.9-rc1 (root@presario) (version gcc 3.3.4 (Debian 1:3.3.4-9))
#1 Thu Sep 2 14:52:15 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
BIOS-e820: 000000001ff70000 - 000000001ff7f000 (ACPI data)
BIOS-e820: 000000001ff7f000 - 000000001ff80000 (ACPI NVS)
BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 130928
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126832 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7280
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1ff7a89f
ACPI: FADT (v001 NVIDIA CK8 0x06040000 PTL_ 0x000f4240) @ 0x1ff7ee34
ACPI: MADT (v001 NVIDIA NV_APIC_ 0x06040000 LTP 0x00000000) @ 0x1ff7eea8
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1ff7ef02
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1ff7ef2a
ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @ 0x00000000
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 266.119 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514768k/523712k available (1923k kernel code, 8176k reserved, 1004k
data, 120k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 517.12 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff c1d3fbff 00000000 00000000
CPU: After vendor identify, caps: 078bfbff c1d3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c1d3fbff 00000000 00000010
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP Processor 3000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd8bc, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040715
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 33)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUS0] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LPID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Cannot allocate resource region 4 of device 0000:00:01.1
PCI: Cannot allocate resource region 5 of device 0000:00:01.1
get_random_bytes called before random driver initialization
Simple Boot Flag at 0x37 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
Real Time Clock Driver v1.12
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 10 (level, low) -> IRQ 10
loop: loaded (max 8 devices)
Using anticipatory io scheduler
nbd: registered device at major 43
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp: pci dev 0000:02:01.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible
chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xe080e800, 00:0f:b0:08:29:0a, IRQ 10
eth0: Identified 8139 chip type 'RTL-8101'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N060ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: HL-DT-ST DVD+RW GCA-4040N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
input: PC Speaker
i8042.c: Detected active multiplexing controller, rev 1.9.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block
18,max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
NET: Registered protocol family 1
Adding 498004k swap on /dev/hda2. Priority:-1 extents:1
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <[email protected]>
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ndiswrapper version 0.10 loaded (preempt=yes,smp=no)
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ndiswrapper: using irq 11
wlan0: ndiswrapper ethernet device 00:90:4b:59:c5:c4 using driver bcmwl5.sys
ndiswrapper device wlan0 supports WPA with TKIP cipher
ndiswrapper: driver bcmwl5.sys (Broadcom,10/28/2003, 3.40.25.3) added
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 USB 2.0
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 10, pci mem e08c6000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usb usb1: control timeout on ep0out
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xe8000000
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:02.0: nVidia Corporation nForce3 USB 1.1
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 11, pci mem e08c8000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:02.1: nVidia Corporation nForce3 USB 1.1 (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 10, pci mem e0935000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb 2-1: new low speed USB device using address 2
input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.0A]
on usb-0000:00:02.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ts: Compaq touchscreen protocol output
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 48658 usecs
intel8x0: measured clock 16605 rejected
intel8x0: clocking to 48000My config file is in my first message :)
Quoted 1 line
Do you have files in
/sys/devices/system/cpu/cpu0/cpufreq?
I don't.
Quoted 2 lines · Romain Moyne
Quoted 1 line
Do you have files in
/sys/devices/system/cpu/cpu0/cpufreq?I don't.
what about after modprobe powernow-k8 ? (that should also print out some messages in dmesg)
Dave
Le Mercredi 01 Septembre 2004 15:00, Dave Jones a écrit :
Quoted 7 lines · Romain Moyne
Quoted 3 lines
Quoted 1 line
Do you have files in
/sys/devices/system/cpu/cpu0/cpufreq?I don't.
what about after modprobe powernow-k8 ? (that should also print out some messages in dmesg)
powernow-k8 is for athlon64, no ? I have just compiled in the kernel (not as a module) the option powernow-k7 (I have a Athlon XP-M).
So, I can't do modprobe powernow-k7...
Quoted 8 lines
Dave
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 4 lines · Romain Moyne
Le Mercredi 01 Septembre 2004 15:00, Dave Jones a écrit :
Quoted 3 lines · Romain Moyne
Quoted 2 lines
Quoted 1 line
Do you have files in
/sys/devices/system/cpu/cpu0/cpufreq?
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
I don't.
what about after modprobe powernow-k8 ? (that should also print out some messages in dmesg)
powernow-k8 is for athlon64, no ? I have just compiled in the kernel (not as a module) the option powernow-k7 (I have a Athlon XP-M).
So, I can't do modprobe powernow-k7...
You have one of the 32bit models of the athlon64. (Basically a crippled athlon64) (See proc/cpuinfo..)
cpu family : 15
I've not heard reports of whether powernow-k8 works or not on these cpu's, but it should if the cpu reports the powernow capability bits.
My suspicion is that for some reason, your cpu is booting at a low speed. Are there any powernow/power management settings in the BIOS that change this ?
Dave
Hello,
Try rebuilding your kernel _without TSC_...
Regards,
Paul
Paul Rolland, rol(at)as2917.net
ex-AS2917 Network administrator and Peering Coordinator
--
Please no HTML, I'm not a browser - Pas d'HTML, je ne suis pas un navigateur
"Some people dream of success... while others wake up and work hard at it"
Quoted 39 lines
-----Message d'origine-----
De : [email protected] [mailto:[email protected]] De la part de Romain Moyne Envoyé : jeudi 2 septembre 2004 18:32
À : Dave Jones; [email protected]
Objet : Re: Time runs exactly three times too fastLe Mercredi 01 Septembre 2004 15:00, Dave Jones a écrit :
Quoted 7 lines · Romain Moyne
Quoted 3 lines
Quoted 1 line
Do you have files in
/sys/devices/system/cpu/cpu0/cpufreq?I don't.
what about after modprobe powernow-k8 ? (that should also print out some messages in dmesg)
powernow-k8 is for athlon64, no ? I have just compiled in the kernel (not as a
module) the option powernow-k7 (I have a Athlon XP-M). So, I can't do modprobe powernow-k7...Quoted 5 lines
Dave
-
To unsubscribe from this list: send the line "unsubscribelinux-kernel" in
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 19 lines · Romain Moyne
Le Mercredi 01 Septembre 2004 14:15, Zwane Mwaikambo a écrit :
Quoted 12 lines · Romain Moyne
Quoted 11 lines
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success. It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).
Quoted 5 lines
Quoted 2 lines
All my applications (KDE, command "date"...) runs three times too fast. It's very annoying.
Can you try this without cpuspeed or some frequency control daemon running? So disable it in runlevel scripts and then reboot.
Quoted 8 lines
I have not cpuspeed or some frequency control daemon running. I just have this:
presario:/etc/rc2.d# ls S10sysklogd S20alsa S20makedev S20xprint S99kdm S99xdm S11klogd S20exim4 S20pcmcia S89atd S99rmnologin S14ppp S20inetd S20xfs S89cron S99stop-bootlogd presario:/etc/rc2.d#
Do you get any messages prefixed with 'cpufreq' or 'powernow' in your dmesg output ?
Do you have files in /sys/devices/system/cpu/cpu0/cpufreq ? If so, what do they contain?
Dave
Quoted 9 lines · Romain Moyne
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success.
It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).
Hmmm. First of all, if you enable the ACPI PM Time source, does the problem go away?
thanks
-john
A friend of mine had a similar problem when updating his debian system last night, so is this a problem with the current debian patch set?
Apparently it went away after playing with acpi, so maybe it is the PM time source...
--Oliver
Quoted 25 lines · john stultz
Quoted 9 lines · Romain Moyne
Hello, I'm french, sorry for my bad english :(
I have a problem with my kernel: Time runs exactly three times too fast.
I tested the kernel 2.6.8.1 and the 2.6.9-rc1, no success.
It is really strange because yesterday I reinstalled my debian with a kernel 2.6.8.1 (made by me): Time ran correctly. And this morning when I rebooted my computer (Compaq presario R3000 series, R3215EA exactly) the time is running again three times too fast (with the kernel 2.6.8.1 and 2.6.9-rc1).Hmmm. First of all, if you enable the ACPI PM Time source, does the problem go away?
thanks
(quoted diff) +0
-2-john -To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines · Oliver Hunt
A friend of mine had a similar problem when updating his debian system last night, so is this a problem with the current debian patch set?
Apparently it went away after playing with acpi, so maybe it is the PM time source...
I'm not sure, but testing the ACPI PM time source narrows down if it is a cpu frequency issue or a timer interrupt issue.
thanks
-john